KIA K900 2016 Features and Functions Guide
Manufacturer: KIA, Model Year: 2016, Model line: K900, Model: KIA K900 2016Pages: 62, PDF Size: 5.3 MB
Page 11 of 62
DRIVER’S PA NEL
9*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
www.KuTechVideos.com/kh13/2016
BLIND SPOT
DETECTION SYSTEM
VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
Blind Spot Detection (BSD) System*
The Blind Spot Detection (BSD) system uses radar sensors to
monitor surrounding areas and help alert the driver to nearby
vehicles before changing lanes. With the ENGINE STA R T/
STOP button in the ON position, press the BSD button
B to
turn the system ON. The button light will illuminate.
The system will activate when the vehicle is traveling more
than 20 mph and will alert the driver if another vehicle is
detected by the radar s en s o r.
1st-stage alert: When another vehicle is detected within the
BSD system boundar y, a yellow indicator will illuminate
A on
the outside rearview mirrors.
2nd-stage alert: When 1s t stage alert is on and the
driver activates a turn signal, a ashing red indicator will
illuminate
A on the outside rearview mirrors and the
system will sound an alert.
\fear Cross \br a f f i c Alert ( \f C \bA )
If the Rear Cross Tr a f c Alert ( RC TA ) system sensors detect
vehicles approaching from the left or right side, the system
will sound an audible alert, the warning indicators on the
outside rearview mirror will illuminate and a message will
appear on the LCD screen, under these conditions:
§ When the vehicle is in Reverse
§ When the vehicle moves backwards from a parked position
§ When the vehicle is moving less than 6 mph
REMINDER: The RC TA feature can be turned
OFF/ON by pressing the BSD button B.
A
B
Quick \bip
The BSD system will activate when:
1. The system is turned on
2. Vehicle speed is above approximately 20 mph
3. Other vehicles are detected on the rear sides of
the vehicle
REMINDERS:
- The BSD system will not issue a warning if the vehicle
speed is 6 mph or more above the surrounding vehicles
- When the BSD is ON and the ignition is cycled, the BSD
system returns to ON
(Buttons located on driver’s panel,
left of the steering wheel)
29319_Text.indd 911/6/15 10:20 AM
Page 12 of 62
DRIVER’S PA NEL
*IF EQUIPPED 10
Lane Departure Warning System (LDWS)\f
www.KuTechVideos.com/kh13/2016
LANE DEPARTURE
WARNING SYSTEM
VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
A
REMINDERS:
- The LDWS will not issue a warning if the turn
signal is activated
- When the ignition is cycled, LDWS will return to
ON when button is pressed
Power \br u n k Main Control Lever
The Power Tr unk Main Control lever is located to the left of the
steering wheel, below the main button panel.
To open, pull the Power Tr unk Main Control lever
C.
To close, press and hold the Power Tr unk Main Control lever
C.
Fuel Door Release Button
Press the Fuel Door Release button B to open the fuel door.
CB
(Buttons located under driver’s
panel, left of the steering wheel)
The Lane Departure Warning System (LDWS) monitors the
vehicle’s position on the road and issues a warning if the
vehicle is drifting out of the intended lane.
With the ENGINE START/STOP button in the ON position,
press the LDWS button
A to turn the system ON. The
instrument cluster indicator
will illuminate green.
If the LDWS detects that you are driving outside of your lane,
the system may issue a warning on the LCD screen and an
alert may sound, under these conditions:
§ The vehicle speed exceeds approximately 43 mph
§ The LDWS system recognizes the lane the vehicle is
traveling in
For more on how to operate the Power Trunk , see the Power Trunk Operation section,
or refer to the Owner's Manual.
(Button located on left side of the steering wheel)
The Lane Departure Warning System (LDWS) is not a substitute for safe and proper driving. Always drive safely and use caution. LDWS
may not always alert the driver if the vehicle is driven outside of its lane. Refer to the Owner’s Manual for more information.
29319_Text.indd 1011/6/15 10:20 AM
Page 13 of 62
DRIVER’S PA NEL
11*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
REMINDER: When the buttons are not pressed, the Reverse Parking Aid Function will not operate and the outside
rearview mirrors will not rotate downward.
Reverse Parking Aid Function
When the gear shift lever is moved into R (Reverse) and the vehicle is moving backwards, the
outside rearview mirrors will rotate downward to aid in reverse parking.
To turn the Reverse Parking Aid Function ON, press the L (Left)
A or R (Right) B outside
rearview mirror button (LED lit).
To turn O F F, press button(s) again.
The outside rearview mirrors will automatically return to their original positions when:
§ The ENGINE START/STOP button is in the OFF position
§ The gear shift lever is moved out of R (Reverse)
§
The outside rearview mirror switch is in the middle position
A
B
(Button located on door panel)
29319_Text.indd 1111/6/15 10:20 AM
Page 14 of 62
DRIVER’S PA NEL
*IF EQUIPPED 12
REMINDERS:
- The system does NOT automatically park the vehicle
- This is a supplementary system. It is the
responsibility of the driver to always check the
area around the vehicle when parking the vehicle
Parking Guide System (PGS) \f Rear- Camera \bisplay*
§ Press TOP VIEW button to adjust the rear-view angle, as if looking down from above
§ Press the NORMAL VIEW button to adjust the rear-view angle, as a normal rear view perspective
www.KuTechVideos.com/kh13/2016
PARKING GUIDE
SYSTEM (PGS) VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
The Parking Assist System is a supplemental system that
assists the driver by chiming if an object is detected within the
sensing areas in the front or rear of the vehicle when parking or
backing up.
When the ENGINE START/STOP button is ON and the shift
lever is in R (Reverse), the system is activated and the
Parking Assist button indicator is illuminated.
To turn off the Parking Assist System, press the button
A.
Parking Assist System
A
REMINDERS:
- If the vehicle is moving at speeds over 6 mph, the
system may not activate
- When more than two objects are sensed at the
same time, the closest one will be recognized rst
- The Parking Assist System is not a substitute for
proper and safe backing-up procedures. Always
drive safely and use caution when backing up.
The Parking Assist System may not detect every
object behind the vehicle
When parking (parallel parking or backing into or out of a
parking spot) the Parking Guide System (PGS)* displays the
vehicle’s projected trajectory on the navigation monitor. The
system also plays a series of audible tones as the vehicle
approaches an object, making parking e a sier.
The PGS will activate when the back-up light is ON with the
ENGINE START/STOP button ON and the shift lever in the
R (Reverse) position.
The rear-view angle of the camera can be changed by pressing
the following buttons on the navigation display:
(Buttons located on driver’s panel,
left of the steering wheel)
29319_Text.indd 1211/6/15 10:21 AM
Page 15 of 62
DRIVER’S PA NEL
13*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
Power Folding Outside Mirrors
D Press the L or R buttons to select the mirror to adjust
E Press button arrows left /right or up/down to adjust
mirror position
F To g gle button left /right to unfold/fold the outside
rearview mirrors
F To g gle button to center to automatically fold/unfold
mirrors when:
§ Smart Key lock /unlock buttons are pressed
§ Outside door handle button is pressed
§ Driver approaches the vehicle with the Smart Key
A Pull/Press to operate driver’s window auto up/down
B Press to unlock /lock all doors
C Press to disable all passenger windows
REMINDERS:
-
To automatically fold mirrors when exiting
vehicle, press the LOCK button twice on the
Smart Key
- To lock the mirror position, toggle button to the
neutral (center) position
Power Windows, Window \fock & \bentral Door \fock
Quick Tip
The mirrors will automatically unfold when the
Smart Key* is within close proximity to the vehicle.
Mirror heaters will operate when the rear defroster is activated.
Heated Outside Mirrors
Auto Door \fock/Unlock
Auto Door Lock /Unlock will engage when gear shift is moved in to or out of the P (Park)
position. Refer to the User Settings on how to turn Auto Door Lock /Unlock ON/OFF.
ABC
EDF
29319_Text.indd 1311/6/15 10:21 AM
Page 16 of 62
DRIVER’S PA NEL
*IF EQUIPPED 14
To start the engine:
1. Depress the brake pedal
2. Press the ENGINE START/STOP button while gear shift is
in P (Park)
To turn the engine O F F, press the ENGINE START/STOP
button while the gear shift is in P (Park).
To use the ENGINE START/STOP button, you must have the
Smart Key on your person or inside the vehicle.
Engine Start/Stop Button
www.KuTechVideos.com/kh13/2016
ENGINE STA RT/STOP
BUTTON AND
SMART KEY VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
REMINDERS:
-
If Smart Key fob battery is dead, you can still start the engine by pressing
the ENGINE START/STOP button with the Lock-button end of the Smart
Key. The Smart Key must contact the ENGINE START/STOP button directly,
at a right angle
- In an emergency situation while the vehicle is in motion, you are able to turn
the engine off and to the ACC position by pressing the ENGINE STA RT/ STOP
button for more than 2 seconds or 3 times successively within 3 seconds
B
CA
Quick Tip\f
To use electrical accessories:
ACC position
- When in the OFF position A and without
depressing the brake pedal, press the ENGINE
START/STOP
button once. The ACC indicator will illuminate (amber) B.
To check warning lights:
ON position
- When already in the ACC position
B and without
depressing the brake pedal, press the ENGINE
START/STOP button again. The ON indicator will
illuminate (red)
C.
- When in the OFF position
A and without
depressing the brake pedal, press the ENGINE
START/STOP button twice. The ON indicator will
illuminate (red)
C.
Keeping the vehicle in ACC or ON position too long
can discharge the vehicle’s battery.
29319_Text.indd 1411/6/15 10:21 AM
Page 17 of 62
STEERING WHEEL CONTROLS
15*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
Power Tilt/Telescoping Steering Wheel
To adjust the steering wheel distance, move the switch A forward or backward.
To adjust the steering wheel angle, move the switch
A up or down.
A
B
(Switch located on left side of steering wheel)
\fuick Tips
- If ignition is turned OFF then ON again within 30
minutes of the steering wheel heater being turned
ON, the system will remain in the ON position
- System does NOT turn off when ignition is
cycled. To turn system of f, press the heated
steering wheel buttonWhile the ENGINE START/STOP button is in the ON position,
press B to turn steering wheel heater ON. The button
indicator will illuminate.
The steering wheel heater will turn off automatically in 30
minutes, or when button is pressed again to deactivate.
He\bted Steering Wheel*
(Button located on left side of steering wheel)
29319_Text.indd 1511/6/15 10:22 AM
Page 18 of 62
STEERING WHEEL CONTROLS
*IF EQUIPPED 16
Tu r n Signals & Fog Lights
To operate:
§ Move lever up/down for right /left turn signal
§ Slightly move lever up/down to activate one-touch lane
change signal
§ Press toggle switch
A up to turn fog lights ON/OFF
REMINDERS:
- Headlights must be ON for fog light operation
- One-touch lane change signal is activated by
moving the turn signal lever slightly for less than 1
second and then releasing. The lane change signal
will blink 3 times
- To change how many times the lane change signal
blinks (3/5/7), go to User Settings in the LCD
instrument cluster modes
For more information on the User Settings Mode,
please refer to your Owner’s Manual.
A
Hea\flights & High Beams
AUTO Light* – When the light switch is in the AUTO
Light position, the tail lights and headlights will turn
ON/OFF automatically depending on the amount of light
outside the vehicle.
AFLS (Adaptive Front Lighting System) – AFLS helps improve
visibility during nighttime driving by aiming the low-beam
headlights in the direction the vehicle is moving. AFLS controls
the aiming direction based on steering angle and speed.
When the light switch is in the AUTO light position, AFLS
will activate.
REMINDER: When the AFLS indicator illuminates on the instrument cluster, the
AFLS is not working properly. See authorized Kia dealer for service.§ Press lever away from you to turn
high beam headlights ON
§ Pull lever to ash headlights/
high beams
Headlight
/ High Beam Lever Operation
§ Rotate lever switch to change the
headlight function:
Headlight position
Parking light position
A\bTO *Auto Light* / AFLS position
DRL/OFFOFF or DRL OFF position
Daytime Running Lights (DRL) – DRL makes it easier for
others to see the front of your vehicle during the day. The lights
will be on automatically unless one of the following occurs:
§ Headlights are on
§ Parking brake is applied
§ Fog lights are on §
Switch is in the DRL
OFF position
§ Engine is turned off
29319_Text.indd 1611/6/15 10:22 AM
Page 19 of 62
STEERING WHEEL CONTROLS
17*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
A
Windshield Wipers & Washers
To operate:
§ Move lever up/down to change wiper modes
M I S T: Single wipe
OFF: Wiper off
AUTO: Auto Rain Sensing LO:
Slow wipe
HI: Fast wipe
§ Pull to spray and wipe
Quick Tips
- When the ENGINE START/STOP button is in the
ON position and the wiper switch is in AUTO
mode, the wiper will automatically operate once
to perform a self-check of the system
- Set the wiper to the OFF position when the wiper
is not in use
- If going through a car wash, remind the
attendant to keep the vehicle in Neutral (N)
and keep the engine running. Also, disable the
Power Trunk lid control using the button inside
the glove compartment, turn off the auto rain-
sensing wipers and fold in the mirrors
Au\fo Rain Sensin\b
The rain sensor located on the upper end of the windshield
glass senses the amount of rainfall and controls the wiping
cycle for the proper interval. The more it rains, the faster the
wiper operates. When the rain stops, the wiper stops.
To turn ON the auto rain-sensing wipers, move lever up/down
to AUTO.
To adjust the auto rain-sensing wiper speed setting, move
the speed control switch
A up/down.
www.KuTechVideos.com/kh13/2016
AUTO RAIN-SENSING
WINDSHIELD WIPERS
VIDEO
To view a video on your
mobile device, snap this
QR Code or visit the listed
website. Refer to page 2
for more information.
LCD Con\frols and Modes
The LCD modes B on the instrument cluster can be
changed using the control buttons C on the right side of
the steering wheel.
Press Mode buttons
/ to change LCD mode.
Press Move buttons
/ to select item.
Press Select/Reset button
in center to set/reset the item.
C
B
For more detailed information, see the LC D Instrument Cluster Modes section on page 6.
29319_Text.indd 1711/6/15 10:22 AM
Page 20 of 62
STEERING WHEEL CONTROLS
*IF EQUIPPED 18
The Advanced Smart Cruise Control (ASCC)* system allows
you to set the vehicle to maintain a speed so long as it is not
limited by traf c. When traf c is encountered, the vehicle will
be slowed to maintain a set distance behind traf c without
depressing the accelerator or brake pedal.
To set /adjust the ASCC speed:
§ Press the CRUISE button up
A to turn system ON. The
CRUISE indicator will illuminate on the instrument cluster
§ Accelerate/decelerate to the desired speed
§ Press the RES+ / S E T- button up/down
B to set or
adjust speed
To set the vehicle-to-vehicle distance:
§ Press the ASCC button
C on the steering wheel.
§ Each time you press
C the vehicle-to-vehicle distance
will change, indicated by the number of bars that appear
on the display
D
To turn the ASCC system OFF:
§ Press the CANCEL button
E. The CRUISE indicator on the
instrument cluster will turn off and the LCD screen ASCC
image will show cancelled
Advanced Smart Cruise Control (ASCC\f*
Quick \bips
The speed setting for the ASCC can be adjusted
under the following conditions:
- With no vehicle in front, you must be travelling at
a minimum speed of 20 mph
- When following a vehicle, there is no minimum
speed requirement
When following a vehicle, the system will
automatically adjust your cruise speed based on
the vehicle in front. It will even bring the vehicle to
a complete stop if necessary. If the vehicle remains
at a standstill for more than 3 seconds, the system
will disable.
To change the cruise control mode from ASCC to
standard cruise control, press and hold button
C.
Repeat to switch back to ASCC mode. (The ASCC
system must not be activated to change modes).
www.KuTechVideos.com/kh13/2016
ADVANCED SMART
CRUISE CONTROL
(ASCC) VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
REMINDERS:
-
CRUISE indicator must be ON in order to
operate ASCC
- The cruise control system will not activate until
the brake pedal has been depressed at least once
after ignition ON or engine starting
C
BA
E65mphCRUISE
(Display on
instrument cluster)
(Buttons located on right side of the steering wheel)D
29319_Text.indd 1811/6/15 10:22 AM