run flat Lancia Delta 2011 Owner handbook (in English)

124KNOWING YOUR CAR
IMPORTANT The steering may become slightly stiff fol-
lowing parking manoeuvres involving a lot of steering.
This is normal and is caused by a system to prevent the
motor from overheating. No servicing is required. The
power steering system will start working normally again
the next time the car is used.T.P.M.S. SYSTEM
(Tyre Pressure Monitoring System)
(for versions/markets, where provided)
The car may be equipped with a tyre pressure monitor-
ing system. This system comprises a radio frequency
transmitter fitted to each wheel (on the wheel rim inside
the tyre), which is able to send information on the tyre
inflation pressure of each wheel to the control unit.
IMPORTANT NOTES ABOUT THE TPMS SYSTEM
The fault indications are not stored and will therefore
not be displayed after the engine has been switched off
and then on again. If the fault conditions persist, the
control unit will send the relative indications to the in-
strument panel only after the vehicle has been in motion
for a short time.
Before starting any servicing operation, stop
the engine and remove the key from the igni-
tion switch to operate the steering lock, par-
ticularly when the wheels do not touch the ground.
If this is not possible (e.g. if the key must be kept in
the MAR position or the engine must be kept run-
ning), remove the electric power steering system
main fuse.
The TPMS is not able to warn you of sud-
den tyre pressure losses (for example when
a tyre bursts). In this case stop the car, brak-
ing with care and avoiding sharp steering actions.

176STARTING AND DRIVING
USING THE MANUAL GEARBOX
To engage the gears, press the clutch pedal fully and shift
the gear lever into the required position (the gear diagram
varies according to the different versions and is shown on
the knob or on the plate below the lever fig. 2).
To engage 6t
hgear, operate the lever by pressing it to-
wards the right in order to avoid engaging 4thgear by
mistake. The same goes for changing from 6thto 5th.
IMPORTANT The car can only be put into reverse gear
when it has stopped moving completely. With the engine
running, wait at least 2 seconds before engaging reverse
gear with the clutch pressed down to the floor in order
to avoid damaging or grinding the gears.
fig. 2L0E0073m
To engage reverse gear R from neutral, raise ring A un-
der the knob and at the same time move the gear lever
to the left and then forwards.
In 1.6 Multijet version: to engage reverse R from neutral,
lift the sliding ring A under the knob and shift the lever
to the right and back.
IMPORTANT The clutch pedal should be used only to
change gear. Do not drive with your foot resting on the
clutch pedal, however lightly. For versions/markets where
provided, the electronic clutch control could cut in, in-
terpreting the incorrect driving style as a fault.
Press the clutch pedal fully to change gears
correctly. For this reason, there must be no
obstacles on the floor under the pedals: en-
sure that rubber mats (if any) are lying flat and
do not interfere with the pedals.
Do not drive with your hand resting on the
gear lever, because this pressure, even if
light, over time can wear out the internal
gearbox components.

IN AN EMERGENCY187
4
In the event of a puncture caused by foreign
bodies, the kit may be used to repair tyres
showing damages on the track or shoulder
up to max. 4 mm diameter.
Give the instruction booklet to the personnel
charged with handling the treated tyre.
The kit cannot be used to repair damage to
the tyre sidewall. Do not use the quick repair
kit if the tyre is damaged as the vehicle has
run on a flat tyre.
If the wheel rim is damaged (bad groove dis-
tortion causing air leakage) it cannot be re-
paired. Do not remove the foreign body
(screw or nail) from the tyre.
IMPORTANT INFORMATION:
The sealing fluid of the quick tyre repair kit is effective
with external temperatures between −20 °C and +50 °C.
The sealing fluid will expire.
Do not operate the compressor for longer
than 20 consecutive minutes. Risk of over-
heating. The quick repair kit is not suitable
for definitive repairs. Tyres may only be repaired
temporarily.

194IN AN EMERGENCY
The driving characteristics of the car may
change when a space-saver wheel is fitted.
Avoid sudden acceleration and braking, sud-
den steering and fast cornering. The total life of
a space-saver wheel is approximately 3000 km,
after which it must be replaced by another wheel of
the same type. Never attempt to fit a conventional
tyre on a rim designed for use as a space-saver
wheel. Have the punctured wheel repaired and re-
placed as soon as possible. Two or more space-
saver wheels should never be used together. Do not
apply grease to the bolt threads before assembly:
they might spontaneously unscrew.The jack can only be used for changing
wheels on the car with which it is provided or
on cars of the same model Never use the jack
for other purposes, such as lifting other car models.
In no case should it be used for repairs under the
car. Incorrect positioning of the jack may cause the
jacked car to fall. Do not use the jack for loads
higher than those shown on the label. Snow chains
cannot be fitted to the space-saver wheel. So, if
a front (drive) wheel is punctured and chains are
needed, a rear wheel should be fitted to the front of
the car and the space-saver wheel should be fitted
to the rear. This way, with two normal front driving
wheels, you can install the snow chains on them,
thus resolving the emergency.
If the hub cap is not installed properly, it
may detach when the vehicle is running.
Never tamper with the inflation valve. Never
introduce tools of any kind between rim and tyre.
Regularly check tyre and space-saver wheel pres-
sure, complying with the data in the chapter “6”.
Tool box (versions with Bose HI-FI)
There is a tool box located in the luggage compartment
for versions with Bose HI-FI.
This box contains:
❍screwdriver;
❍tow hook;
❍wheel bolt spanner;
❍wheel bolt access spanner;
❍alloy wheel centring device;
❍jack.

IN AN EMERGENCY199
4
REFITTING THE STANDARD WHEEL
Following the procedure described previously, raise the
car and remove the space saver spare wheel.
Versions with steel rims
Proceed as follows:
❍make sure the contact surfaces between standard
wheel and hub are clean so that the fastening bolts
will not come loose;
❍fit the standard wheel inserting the 4 bolts into the
holes;
❍using the wrench provided, tighten the fastening bolts;
❍press-fit the hub cap, aligning the special splining (on
the cap) with the inflation valve;
❍lower the car and remove the jack;
❍using the wrench provided, fully tighten the bolts in
the sequence shown previously.Versions with alloy wheels
❍Place the wheel onto the hub and tighten the bolts us-
ing the wrench provided;
❍lower the car and remove the jack;
❍using the spanner provided, fully tighten the bolts in
the sequence shown in fig. 8;
❍refit the press-fitted hub cap, making sure that the
reference hole on the wheel is aligned with the refer-
ence pin on the cap.
IMPORTANT If it is not fitted properly, the hub cap may
detach when the vehicle is running.