Lancia Musa 2007 Owner handbook (in English)

100
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
MAIN BEAM HEADLIGHTS
When the knurled ring is at 2pull the lever towards the steering
wheel (stable position).
The warning light 1on the instrument cluster will come on.
Pulling the lever towards the steering wheel again, the main beams
are turned off (and the dipped beams on).
FLASHING THE HEADLIGHTS
Pull the lever towards the steering wheel (unstable position)
regardless of the position of the knurled ring.
IMPORTANT Check on the display that stable position is not
engaged.
L0D0069m
L0D0070m

101
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
DIRECTION INDICATORS
Move the stalk:
❒up (stable position 1): to engage the right-hand direction
indicator;
❒down (stable position 2): to engage the left-hand direction
indicator.
Warning light ForDwill come on flashing on the instrument cluster.
Indicators are switched off automatically when the steering wheel is
straightened.
If you want the indicator to flash briefly to show that you are about to
change lane, move the stalk up or down without clicking into position
(unstable position). When released the stalk will return to its home
position.
L0D0071m

102
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
“FOLLOW ME HOME” DEVICE
This function allows the illumination of the space in front of the car
for a preset time.
Activation
With the ignition key at STOP or removed, pull the stalk towards the
steering wheel and operate it within 2 minutes from when the engine
is turned off.
At each single movement of the stalk, the staying on of the lights is
extended by 30 seconds up to a maximum of 210 seconds; then the
lights are switched off automatically.
Each time the lever is operated, the 3warning light turns on
together with the message on the display (see section “Warning lights
and messages”).
Deactivation
Keep the stalk pulled towards the steering wheel for more than 2
seconds.
L0D0070m

103
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
AUTOMATIC HEADLIGHTS SENSOR (daylight sensor)
(where provided)
It detects the changes of the external light intensity of the car
according to the light sensitivity set: greater is the sensitivity, smaller
is the amount of external light necessary to control the switching-on
of the exterior headlights. The daylight sensor sensitivity can be
adjusted with the “Set-up menu” of “multifunction display”.
Activation
Turn the knurled ring to
2A: in this way, the automatic activation of
the side/taillights and dipped beam headlights is simultaneously
enabled according to the external luminosity.
When the daylight sensor is on, the display shows the preset
sensitivity level. During displaying, the sensitivity level can be
adjusted using buttons +and–.
Deactivation
As a result of the sensor control, the dipped beam headlights will
switch off and, after about 10 seconds, sidelights will switch off too.
If during automatic light activation,
main beam headlights have been switched on (manually), they will go
off at automatic light switching off.
IMPORTANT The light sensor is not able to detect the fog presence,
lights shall therefore be switched on manually.
L0D0072m
L0D0025m

104
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
WINDOW WASHING
WINDSCREEN WASHER/WIPER
This device can only work when the ignition key is at MAR.
The stalk can be moved to five different positions:
A windscreen wiper off
B flick wipe.
With the stalk in position B, turning the knurled ring F, four possible
intermittent speeds are obtained:
,= very slow intermittent
--= slow intermittent
---= intermittent medium
----= fast intermittent
C continuous slow;
D continuous fast;
E fast temporary (unstable position).
Operation in position E is limited to the time the lever is held in this
position. When the lever is released, it returns to position A
automatically stopping the wiper.
IMPORTANT Change blades as indicated in section
“Car Maintenance”.
Never use the window wiper to remove ice or snow from the windscreen. In these conditions, the
wiper is submitted to excessive effort that results in motor protection cutting in and wiper
operation inhibition for few seconds as a consequence. If operation is not restored contact Lancia
Dealership.
L0D0073m

105
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
“Smart washing” function
Pulling the stalk towards the steering wheel (unstable position)
operates the windscreen washer.
Keeping the stalk pulled for over half a second, with just one
movement it is possible to operate the washer jet and the wiper at the
same time.
Releasing the stalk will stop the washer jet immediately whereas the
wiper stops working four strokes later.
A further “cleaning stroke” after five seconds, completes the wiping
operation.
L0D0074m

106
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
RAIN SENSOR (where provided)
The rain sensor A is located behind the driving mirror in contact with
the windscreen and has the purpose of automatically adjust, during
the intermittent operation, the frequency of the windscreen wiper
strokes as to the rain intensity.
IMPORTANT Keep clean the glass in the sensor area.
Activation
Move the right-hand stalk downwards by one position.
The activation of the rain sensor is signalled by a control acquisition
“stroke”.
L0D0245m

107
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Turning the knurled ring F it is possible to increase the sensitivity of
the rain sensor.
The increase of the sensitivity of the rain sensor is signalled by a
control and acquisition “stroke”.
Operating the windscreen washer with the rain sensor activated will
start the smart washing function (without the additional cleaning
stroke after five seconds), at the end of which the rain sensor resumes
its normal automatic function.
Deactivation
Remove the stalk from position B or turn the ignition key to STOP.
At the following starting operation (key at MAR), the sensor will not
be reactivated even if the stalk is still at B. To activate the rain sensor,
move the stalk to A or C and then again to B or turn the sensitivity
adjustment knurled ring.
Rain sensor activation is indicated by a wiper “stroke”.
The rain sensor is able to recognize and automatically adjust itself in
the presence of the following particular conditions:
❒impurities on the controlled surface (salt, dirt, etc.);
❒difference between day and night.
Water streaks could cause non-required wiping.WARNING
L0D0073m

108
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
REAR WINDOW WASH/WIPE FUNCTION
This device can only work when the ignition key is at MAR.
Turning the knurled ring A from åto
'the rear window wiper is
operated as follows:
❒intermittent operation if the windscreen wiper is off
❒synchronised with the windscreen wiper (but with half stroke
frequency).
With windscreen wiper on and reverse gear engaged, rear window
wiping will be continuous.
Pushing the stalk towards the dashboard (unstable position) will
activate the rear window washer.
Pushing the stalk for over half a second will activated also the rear
window wiper.
Releasing the stalk will activate the smart washing function as
described for the windscreen wiper.
L0D0075m

109
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
CRUISE CONTROL (where provided)
It is a device able to support the driver, with electronic control, which
allows driving at speed over 30 km/h on long and straight dry roads
(e.g.: motorways), at a desired speed, without pressing the accelerator
pedal. Therefore it is not suggested to use this device on extra-urban
roads with traffic. Do not use it in town.
DEVICE ENGAGEMENT
Turn knurled ring A to ON.
The device may only be engaged in the 4th or 5th gear. Travelling
downhill with the device engaged, the car speed may increase more
than the memorised one.
When the device is activated, the warning light
Üon the instrument
cluster turns on together with the message (where provided) on the
multifunction display.
L0D0076m