display Lancia Musa 2007 Owner handbook (in English)

Cruising range= shows the distance (in km or
miles) that the car can still cover before needing
fuel, assuming that driving conditions are kept
unvaried. The display will show “- - - -” in the
following cases:
❒value for range to empty lower than 50 km or
fuel level below 4 litres; in this event before “- -
- -” the message “Warning, limited range” will
be displayed (this message will be displayed also
if not in TRIP COMPUTER mode);
❒in case of car parked with engine running for a
long period, when the car moves off the range to
empty indication will be displayed again.
Travelled distance= shows the km (or miles)
covered from last reset (*).
Average fuel consumption= shows the average
consumption calculated from last reset (*), this
value can be expressed in l/100 km or mpg.
Instant consumption= shows the fuel
consumption variation updated every second, it can
be expressed in l/100 km or mpg. In case of car
parked with engine running the display will show “-
- - -”. When the car moves off the instant
consumption indication will be displayed again.
Average speed= shows the average speed of the
car in relation with total time elapsed from last reset
(*), this value can be expressed in km/h or in mph.
35
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Travel time= time elapsed from last reset (*).
(*) Reset can be:
– “manual”, reset is performed by the driver by
pressing the relevant button (see paragraph
“Control buttons”)
– “automatic”, reset is performed when the
travelled distance reaches 3999.9 km or when
travel time reaches 99:59 (99 hours and 59
minutes)
– after reconnecting the battery.
IMPORTANT Lacking information, Trip computer
values are displayed with “- - - -”. When restoring
normal operating conditions after a failure,
calculation will restart regularly without resetting
values.
IMPORTANT After battery
disconnection/connection certain displayed values
are equal to “- - - -” until significant data for
calculation are available.

INERTIAL FUEL CUT-OFF SWITCH OPERATION WARNING
MESSAGE
The message shown in the figure is displayed automatically when the
fuel cut-off switch comes into operation after a crash.
This switch stops fuel supply.
See paragraph “Inertial fuel cut-off switch”.
36
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0038m
WARNINGIf after “FPSon” message displaying you smell fuel or see leaks from the fuel
system, do not reset the switch to avoid fire risk.

MULTIFUNCTION DISPLAY
(On three-line comfort panel)
The “Multifunction display” shows all the useful information
necessary when driving, more particularly:
INFORMATION ON STANDARD SCREEN
❒Date A.
❒Mileage recorder B.
❒Clock C.
❒External temperature D.
When the ignition key is removed only the time is displayed; when
opening one of the front doors the display comes on showing the
odometer indication.
INFORMATION ABOUT CAR CONDITIONS (at event)
❒Scheduled maintenance programme intervals.
❒ Trip computer information.
❒To adjust the intensity of the instrument dimmer/ menus/
instrument panel, sound system and automatic two-zone climate
control system display.
❒Display of failure/warning messages/function activation.
❒Display of the CITY mode (if selected).
❒Headlight aiming position display (with dipped beam headlights
on) E.
❒Symbol for possible ice on road.
37
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
FOH9000m

CONTROL BUTTONS
To use the information the “Multifunction display” is able to give you
should firstly familiarise with the control buttons using them as
described below.
Before doing anything you are advised to read this section thoroughly.
+ and – buttons
To scroll the menu and the related options upwards/downwards, to
increase/decrease/set the value displayed and, with side/taillights on,
to adjust the intensity of the instrument dimmer/ menus/ instrument
panel, sound system and automatic two-zone climate control system
display (if pressed with “Set-up menu on”).
MODE button
Press for less than 2 seconds (pulse) indicated with
bin the
following diagrams, to confirm the option required and/or move to
the main screen (same option) or access the Menu.
Press for more than 2 seconds indicated with
cin the following
diagrams, to exit the set-up menu during setting.
TRIP button
Press for less than 1 seconds (pulse) indicated with
hin the
following diagrams, to scroll the Trip computer screens.
Press for more than 2 seconds indicated with
iin the following
diagrams, to reset the Trip computer and start a new mission.
38
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0025m
L0D0026m

39
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
SET-UP MENU
The “Set-up Menu” enables to perform the
following adjustments and/or settings using the
control buttons (see previous pages):
❒SPEED LIMIT
❒AUTOMATIC HEADLIGHT DAYLIGHT
SENSOR (where provided)
❒TRIP B ON/OFF
❒SET CLOCK
❒CLOCK MODE
❒SET DATE
❒SPEEDLOCK
❒INDEPENDENT BOOT
❒DRIVER’S DOOR UNLOCKING❒DISTANCE UNIT
❒CONSUMPTION UNIT
❒TEMPERATURE UNIT (where required)
❒LANGUAGE
❒BUZZER VOLUME
❒BUTTON VOLUME
❒S.B.R. (Seat Belt Reminder) BUZZER
REACTIVATION (*)
❒SERVICE
❒EXIT MENU
(*) This function can be displayed only after Lancia Dealership has deactivated the S.B.R. system.

40
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
INITIAL CHECK
Turning the ignition key to MAR, the multifunction display shows the message “Checking”: the diagnostic
phase of all the electronic systems on the car has started. This lasts few seconds: if no faults are detected, when
the engine has started, the display shows the “Check OK” message.
See section “Warning lights and messages” if faults are found.
Is the
engine
started?YES
If no failures are
present
The “Service schedule” includes vehicle maintenance every 20,000 km (or 12,000 mi) or every year; this is shown automatically,
with the ignition key at MAR, starting from 2,000 km (or 1,240 mi) or 30 days from this deadline and it is shown again every 200
km (or 124 mi) or 3 days. For 1.3 Multijet versions, see “Care and Maintenance” in section “Service schedule to change engine oil
and filter and air cleaner. When a programmed maintenance interval (coupon) is near to come, turning the ignition key to MAR, will
display the message “Service” followed by the number of km, or days to go before car servicing. “Scheduled servicing” message is
displayed in km, miles or days according to the approaching service interval. Contact a Lancia Dealership to carry out any service
operation provided by the “Service schedule” or “Annual inspection plan”, and to reset the display.
If the display shows a failure
message, see details in section
“Warning lights and messages”.
Standard
screen display or
NO

41
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
ACCESS TO MENU SCREEN
After the “Initial check”, it is possible to access the menu screen pressing the button
Q.
To surf the menu press buttons +or–.
IMPORTANT If after entering the menu no setting/adjustment is performed within 60 seconds, the system exits
the menu automatically and returns to previously displayed screen.
In this case the last selected but not confirmed setting (through button
Q) is not stored and therefore the
operation shall be repeated.
When the car is running, it is possible to access only the reduced menu (for setting “Speed limit” and “Daylight
sensor automatic headlights”).
When the car is stationary access to the whole menu is enabled.
The following diagram shows the cases described.
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds

44
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
SPEED LIMIT EXCEEDED (Speed Lim.)
With this function it is possible to set the car speed limit which, if exceeded, automatically sounds a buzzer and
makes the warning light
èwith the special message on the display (see “Warning lights and messages”
section) come on to alert the driver. To set the speed limit, proceed as follows:
The car is delivered with this function set to “OFF”.
R
Q
Q
QR
Q
Q
R
– +
– +
Q
See “Initial check”
and “Access to
menu screen”
Use buttons +/- to select
ON/OFF. Set selection flashes.
Return to menu
screen Menu screenReturn to
previously
displayed
screen, e.g.:
Return to menu
screen
Use buttons +/- to set the speed required (during the setting
operation the value flashes on the screen). The possible setting
is between 30 and 250 km/h or between 20 and 155 mph de-
pending on the unit set previously (see “Dist. Unit” paragraph
described later). Every press (pulse) of the button +/– increases
or decreases by five units. Keeping button +/- pressed obtains
the automatic fast increase or decrease.
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds
R

45
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
DAYLIGHT SENSOR AUTOMATIC HEADLIGHTS (Light Sensor) (where provided)
With this function it is possible to adjust the light sensor sensitivity according to 3 levels (level 1 = min. level,
level 2 = average level, level 3 = max. level); the higher the sensitivity is, the lower is the external light intensity
required to switch on the lights. This operation can be performed also with the car moving. The car is delivered
with this setting on level “2”. To set the light level required, proceed as follows:
R
Q
Q
– +
R
– +
See “Initial check”
and “Access to
menu screen”
Menu screen
Return to menu
screen Use the + or – buttons to set the light
sensor sensitivity.
Set selection flashes.
Return to previously
displayed
screen, e.g.:
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds
QR

46
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
TRIP B ON/OFF (Trip B)
Through this option it is possible to activate (ON) or deactivate (OFF) the Trip B (partial trip) which show
“partial mission” information corresponding to: Trip Dist. B, Aver. Consump. B, Avg. Speed B, Travel time B.
For further information see “General trip - Trip B”.
The car is delivered with this function set to “ON”.
Proced as follows:
R
Q
– + – +
R
QQ
QQ
See “Initial check”
and “Access to
menu screen”
Menu screen
Use buttons +/– to select
ON/OFF. Set selection flashes.
Return to menu
screen Return to menu screenReturn to previously
displayed
screen, e.g.:
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds
RR