reset Lancia Musa 2007 Owner handbook (in English)

65
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
After resetting “Trip” by pressing the button with &mode, the following functions are displayed:
Reset GENERAL TRIP
&= “Reset General trip” and “Trip B”
(excluding “Cruising range”).
&= “Reset Trip B”
Reset TRIP B
All values set to zero
Only partial values are set to zero
%= Press “TRIP” button for less than two seconds - &= Press “TRIP” button for over two seconds

66
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Cruising range= = Shows the distance in km (or
mi) that the car can still cover before needing fuel,
assuming that driving conditions are kept unvaried.
The display will show “- - - - in the following
cases:
❒value for range to empty lower than 50 km or
fuel level below 4 litres; in this event before
“- - - -” the message “Warning, limited range”
will be displayed (this message will be displayed
also if not in TRIP COMPUTER mode);
❒in case of car parked with engine running for a
long period, when the car moves off the range to
empty indication will be displayed again.
Travelled distance= shows the km (or miles)
covered from last reset (*).
Average fuel consumption= shows the average
consumption calculated from last reset (*), this
value can be expressed in l/100 km, km/l or mpg.
Instant consumption = shows the fuel
consumption variation updated every second, it can
be expressed in l/100 km or mpg. In case of car
parked with engine running the display will show
“- - - -”. When the car moves off the instant
consumption indication will be displayed again.
Average speed= shows the average speed of the
car in relation with total time elapsed from last reset
(*) and it can be expressed in km/h or in mph.Travel time= time elapsed from last reset (*).
(*) Reset can be:
– “manual”, reset is performed by the driver by
pressing the relevant button (see paragraph
“Control buttons”)
– “automatic”, reset is performed when the
travelled distance reaches 9999.9 km or when
Travel time reaches 99:59 (99 hours and 59
minutes)
– after reconnecting the battery.
IMPORTANT Lacking information, Trip computer
values are displayed with “- - - -”. When normal
operating condition is reset, calculation of different
units will restart regularly. Values displayed before
the failure will not be reset (*).
IMPORTANT After battery disconnection/
connection certain displayed values are equal to
“- - - -” until significant data for calculation are
available.

68
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
INERTIAL FUEL CUT-OFF SWITCH OPERATION WARNING
MESSAGE
The message shown in the figure is displayed automatically when the
fuel cut-off switch comes into operation after a crash.
This switch stops fuel supply.
See paragraph “Inertial fuel cut-off switch”.
WARNING
If after warning message displaying you smell fuel or see leaks from the fuel
system, do not reset the switch to avoid fire risk.

75
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Relax position, passenger side
To obtain the relax position, open the rear door and:
❒tilt the passenger seat to “table” position (see “Setting the
passenger’s seat to table configuration” in this section);
❒push the rear seat completely forward;
❒push the passenger’s seat (tilted) completely backward;
❒remove the rear parcel shelf (see “Rear parcel shelf removal” in
this section);
❒move the rear seat back rest to the required position.
Relax position, driver side
Same procedure but remove completely the driver’s head restraint
(see “Head restraints” in this section).
IMPORTANT See section “Boot Extension” for operations concerning
seat positioning to extend the boot. Central console adjustment from the boot
Pull band F and push forward the top of the back rest at the same
time until releasing the locking clip. Bring the back rest to horizontal
position then, release band F. Reverse this procedure to reset the back
rest in vertical position. Check for clip locking into place.
L0D0255m
L0D0242m
L0D0243m

86
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
QUICK WINDSCREEN AND FRONT SIDE
WINDOW DEMISTING/DEFROSTING
Proceed as follows:
❒turn knob B to the red sector;
❒turn knob A to 4 -;
❒turn knob E to -;
❒set knob F to Uto turn air recirculation off.
After demisting/defrosting, operate the controls to
restore the required comfort.
Preventive demisting procedure
In the event of considerable outside moisture and/or
rain and/or considerable differences in temperature
inside and outside the passenger compartment,
perform the following preventive demisting
procedure:
❒set knob F to Uto turn air recirculation off;
❒turn knob B to the red sector;
❒turn knob A to 2;
❒turn knob E to to -or to ƒif the windows do
not mist up.
IMPORTANT Climate control is very useful to speed
up window demisting: therefore, perform demisting
procedure as described previously and then switch
the system on pressing button D.REAR WINDOW AND ELECTRIC DOOR
MIRROR DEMISTING/DEFROSTING
(where provided)
Press button C to turn this function on. When this
function is on, the button led turns on.
This function is timed and switches off
automatically after the preset time. To cut out this
function press again button C.
IMPORTANT Do not apply stickers on the inside of
the rear window over the heating filaments to avoid
damage that might cause it to stop working
properly.

95
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
These operating conditions are obtained pressing in
sequence the air recirculation button C.
After a preset time, the climate control system will
turn air recirculation off automatically for safety
reasons, thus enabling outside air inlet.IMPORTANT The air recirculation system
makes it possible to reach the required heating or
cooling conditions faster.
It is however inadvisable to use it on rainy/cold
days as it would considerably increase the
possibility of the windows misting inside, especially
if the climate control system is off.
When the outside temperature is below 5-7°C, air
recirculation is switched off (air is taken from the
outside) to prevent misting.
WARNINGIt is inadvisable to use the air recirculation feature with low outside temperature
as the windows might mist over quickly.

96
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Climate control compressor on/off
button B
Press the
√button, when the button
led is on, to switch the compressor
off. The led will go off. By pressing
again the button when the led is off, the system
automatic control of the compressor activation is
restored; this condition is indicated by button led
lighting up.
When the air conditioner compressor is off, the
system deactivates air recirculation to prevent
window misting up. Although the system is still able
to maintain the required temperature, the message
FULL on the display will go off. If the system is no
longer able to keep the required temperature, also
the message AUTO will turn off.
IMPORTANT Air at a temperature lower than that
of the outside air cannot be let into the passenger
compartment when the compressor is off.
Furthermore, in particular environmental
conditions, the windows could mist up fast because
the air is no longer dehumidified.Setting will be stored also when the engine is
stopped.
Either press again button √(in this case the system
operates as heater only) or AUTO to reset automatic
control of the compressor.
With compressor off, if the outside temperature is
higher than the set temperature, the system cannot
reach the required temperature. This will be
signalled by the flashing of set temperature value on
the display for a few seconds, then the message
AUTO will go off.
When the compressor is off, it is possible to reset
manually the fan speed (no bar displayed).
When the compressor is on and the engine is
running, fan speed cannot be lower than the
minimum (one bar displayed).

97
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Button for fast windscreen and
front side window
demisting/defrosting F
Press this button: the climate control
system will automatically switch on
all the functions required for fast windscreen and
front side window demisting/defrosting, that is:
❒climate control system compressor on (with
proper climatic conditions);
❒air recirculation off;
❒maximum air temperature HI on both areas;
❒fan speed according to engine coolant
temperature in order to limit letting cold air into
the passenger compartment for demisting the
windows;
❒air flow directed to the windscreen and front side
window vents;
❒heated rear windowIMPORTANT The fast windscreen
demisting/defrosting function stays on for approx.
3 minutes after the engine coolant temperature
exceeds 50°C (petrol versions) or 35°C
(Multijet versions).
When the max. demisting/defrosting function is on,
the led on the relevant button and that on the
heated rear window button turn on. Message FULL
AUTO on the display will turn off.
When the max. demisting/defrosting function is on,
the only manual operations possible are manual
adjustment of the fan and switching rear window
heating off.
Press button F or air recirculation button C or
compressor button B or AUTO buttons N o H to
reset the previous system operation conditions.

98
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Button for demisting/defrosting
the heated rear window and door
mirrors G
Press this button to switch on the
heated rear window
demisting/defrosting function. The led on the
button will come on.
This function will be automatically switched off
after the preset time, or pressing the button again or
when stopping the engine. It will not start up
automatically when the engine is started again.
IMPORTANT Do not apply stickers on the inside of
the rear window over the heating filaments to avoid
damage that might cause it to stop working
properly.❒climate control system compressor off;
❒fan off.
The heated rear window can be switched on and off
normally when the system is off by pressing button
G.
IMPORTANT The climate control system electronic
unit stores the system settings made before the
system was switched off and restores them as soon
as a button is pressed (with the exception of the
heated rear window button). The function which
the button corresponds to will be switched on, if it
was off when the system was switched off. It will be
kept if, on the other hand, it was on when the
system was switched off.
Press the AUTO button to switch the climate control
system back on.
OFF button E (system off)
To switch the climate control system
off, press button E, also the display
will go off.
The climate control system
conditions when the system is off are the following:
❒Every led off;
❒set temperatures not displayed;
❒air recirculation on, thus isolating the passenger
compartment;

102
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
“FOLLOW ME HOME” DEVICE
This function allows the illumination of the space in front of the car
for a preset time.
Activation
With the ignition key at STOP or removed, pull the stalk towards the
steering wheel and operate it within 2 minutes from when the engine
is turned off.
At each single movement of the stalk, the staying on of the lights is
extended by 30 seconds up to a maximum of 210 seconds; then the
lights are switched off automatically.
Each time the lever is operated, the 3warning light turns on
together with the message on the display (see section “Warning lights
and messages”).
Deactivation
Keep the stalk pulled towards the steering wheel for more than 2
seconds.
L0D0070m