fuel Lancia Musa 2009 Owner handbook (in English)

USE OF ENVIRONMENT-FRIENDLY MATERIALS
None of the components installed on LANCIA Musa contains asbestos. The padding and air conditioning system are
CFC-free (Chlorofluorocarbons), these gases being reliable for the depletion of the ozone layer. Dying agents and anti-
corrosion coating of the bolts and screws no longer contain cadmium, which pollutes the air and waterbeds.
EMISSION-REDUCING DEVICES (petrol engines)
Three-way catalytic converter (catalytic converter)
The exhaust system features a catalyst made with alloys of noble metals. It is installed in a stainless steel housing which
is resistant to high operating temperatures.
The catalyst converts the unburnt hydrocarbons, carbon oxide and nitrogen oxides that are present in the exhaust gases
(although in small quantities thanks to electronic injection ignition systems) into non-polluting compounds.
As the catalytic converter reaches high temperatures during car operation, we recommend that the car should not be
parked on materials that may pose a risk of flammability (e.g. paper, fuel oils, dry grass or leaves, etc.).
Lambda sensors
These sensors (Lambda) detect the oxygen content in the exhaust gases. Lambda sensors produce a signal which is
used by the electronic control unit of the injection and ignition system for regulating the air-fuel mix.
Fuel evaporation system
Even when the engine is not running, it is not possible to prevent the formation of petrol vapours. For this reason, a
system has been developed to “catch” these vapours in a special activated carbon vessel.
While the engine is running, these vapours are aspirated and delivered to combustion.
001-006 MUSA 1ed GB 10-07-2008 9:36 Pagina 3

MUST BE READ!
REFUELLING
Petrol engines:exclusively refuel the car with unleaded petrol having a RON that must not be below 95.
Multijet engines:exclusively refuel the car with vehicle propulsion diesel fuel conforming to the European
specification EN590.
The use of other products or mixtures may damage the engine beyond repair and consequently cause the
warranty to be void depending on the damage caused.
ENGINE STARTING
Petrol engines:make sure that the handbrake is engaged; set the gearshift lever to neutral; fully depress
the clutch without pressing the accelerator, then turn the ignition key to AV Vand release it as soon as the
engine has started.
Multijet engines:turn the ignition key to MARand wait until the warning lights Yandmgo off. Then
, turn the ignition key to AV Vand release it as soon as the engine has started.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter develops high temperature during operation. Do not park on grass, dry leaves,
pine needles or other flammable material: fire risk.
ENVIRONMENTAL PROTECTION
The car is fitted with a system that allows continuous diagnosis of the emission-related components to
ensure better respect of the environment.

K
001-006 MUSA 1ed GB 10-07-2008 9:36 Pagina 5

7
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLSDASHBOARD ........................................................ 8
INSTRUMENT PANEL.......................................... 10
SYMBOLS ............................................................. 11
THE LANCIA CODE SYSTEM .............................. 11
THE KEY AND DOOR LOCKING KIT ................. 13
IGNITION DEVICE .............................................. 20
INSTRUMENTS ................................................... 21
MULTIFUNCTIONAL DISPLAY
(on two-line modal panel) ...................................... 22
MULTIFUNCTIONAL DISPLAY
(on three-line modal panel).................................... 25
ADJUSTING THE SEATS ..................................... 38
HEAD RESTRAINTS ............................................ 44
ADJUSTING THE STEERING WHEEL ............... 45
REARVIEW MIRRORS .......................................... 46
HEATING/CLIMATE CONTROL SYSTEM .......... 47
MANUAL CLIMATE CONTROL SYSTEM ........... 48
AUTOMATIC CLIMATE CONTROL
SYSTEM (TWO-ZONE) ....................................... 52
EXTERNAL LIGHTS ........................................... 62
WINDOW WASHING ............................................ 64
CRUISE CONTROL ............................................. 67CEILING LIGHTS ................................................. 69
LIGHT CONTROL BUTTONS .............................. 71
FUEL CUT-OFF INERTIAL SWITCH ................... 72
INTERNAL EQUIPMENT .................................... 73
SMOKERS KIT ...................................................... 75
SUN VISORS ......................................................... 76
SUNROOF ............................................................ 76
POWER WINDOWS ............................................. 78
BOOT .................................................................... 80
BONNET ............................................................... 82
ROOF BARS .......................................................... 83
HEADLIGHTS ...................................................... 84
ABS SYSTEM ....................................................... 85
EOBD SYSTEM .................................................... 86
SOUND SYSTEM .................................................. 87
ACCESSORIES PURCHASED BY THE OWNER .. 88
“DUALDRIVE” ELECTRIC POWER
STEERING SYSTEM ............................................ 89
PARKING SENSORS ............................................ 90
REFUELLING ...................................................... 92
ENVIRONMENTAL PROTECTION ..................... 94
DASHBOARD AND CONTROLS
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 7

10
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
L0D0372m
L0D0010m
fig. 7
fig. 8
INSTRUMENT PANEL
Modal panel
A - Speedometer (speed indicator)
B – Fuel level gauge with reserve warning light
C – Engine coolant temperature gauge and
excessive temperature warning light
D - Rev. counter
E - Multifunctional display
cmWarning lights installed on Multijet versions
only
Comfort
A - Speedometer (speed indicator)
B – Fuel level gauge with reserve warning light
C – Engine coolant temperature gauge and
excessive temperature warning light
D - Rev. counter
E - Reconfigurable multifunctional display
cmWarning lights installed on Multijet versions
only
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 10

13
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
THE KEY AND
DOOR LOCKING
KIT
CODE CARD Fig. 10
(Optional for versions/markets
where applicable)
The car is delivered with the ignition
key and the CODE card which bears
the following data:
❒the mechanical key code Bto be
given to the Lancia Dealership
when ordering duplicate keys.
IMPORTANT In order to ensure per-
fect efficiency of the electronic devices
inside the keys, they should never be
exposed to direct sunlight.MAIN KEY WITH REMOTE
CONTROL fig. 11
The metal insert of the key Ais re-
cessed in the grip.
The key operates:
❒the ignition switch;
❒the lock of the door on the driver’s
side;
❒the lock/release device of the fuel
flap (on versions equipped with a
lockable fuel plug)
fig. 10L0D0376m
All the keys and the CODE
card must be handed over to
the new owner when selling
the car.
fig. 11L0D0377m
❒engagement of the device, D-fig.
12, for locking external opening of
the front and rear doors when the
electric system does not work (e.g.
the battery is down);
❒engagement of the child safety
lock device, E-fig. 12, installed on
the rear doors.
ButtonB-fig. 11enables opening of
the metal insert A.
fig. 12L0D0246m
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 13

14
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT The remote control fre-
quency may be disturbed by radio
transmissions outside the car (e.g. cel-
lular phones, radio amateurs, etc.). If
this is the case, the remote control
may operate incorrectly.
Door and tailgate locking
Short pressure on button Á: remote
lock of doors, tailgate and fuel flap,
switching off of the internal ceiling
lights and single flashing of direction
indicators. Door and tailgate lock release
Short pressure on button Ë: lock re-
lease of doors, tailgate and fuel flap,
timed switching on of the internal
ceiling lights and double flashing of
direction indicators.
Door locks are automatically released
in case of intervention of the inertial
fuel cut-off switch.
Use the “Setup Menu” of the multi-
functional reconfigurable display (see
the dedicated paragraph in section
“Dashboard and Controls”) to set the
system in such a way that only the
door on the driver’s side is released
when pressing button Ë. To refit metal insert A, proceed as
follows:
❒Press button Band hold it pressed.
❒move the metal insert A.
❒Release button Band turn the
metal insert Auntil hearing the
click that indicates correct locking.
The button
Ëactivates the release de-
vice for doors, tailgate and fuel flap
(where provided).
The button
Áactivates the release de-
vice for doors, tailgate and fuel flap
(where provided).
The button Ractivates opening of
the tailgate.
Press button B-fig. 11 only
after moving the key away
from your body, especially your
eyes, and from objects which could
get damaged (e.g. your clothes). Do
not leave the key unattended, be-
cause someone, a child especially,
may accidentally press the button
while handling the key.
WARNING
fig. 13L0D0378m
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 14

17
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
(SPARE) MECHANICAL
KEY, fig. 17-18
Depending on the version, the car is
either supplied with a recessed key 1
or fixed key 2.
The metal insert Aof the key 1is re-
cessed in the grip.
The button Bactivates opening of the
metal insert A.
The metal insert Ais placed back in
the grip as follows.
❒Press button Band hold it pressed.
❒Move the metal insert A.
❒Release buttonBand turn the
metal insertAuntil hearing the
click that indicates correct locking.The keys are used to activate:
❒the ignition switch;
❒the lock of the door on the driver’s
side;
❒the fuel flap lock/release (on ver-
sions supplied with a lockable
plug)
❒engagement of the child safety
lock device when the electric sys-
tem does not work (e.g. when the
battery is down);
❒engagement of the child safety
lock device on the rear doors.
fig. 17L0D0014mfig. 18L0D0380m
Only press button B with
the key away from your
body, specifically from your eyes
and from objects which could get
damaged (e.g. your clothes). Do not
leave the key unattended, because
someone, a child especially, may ac-
cidentally press the button while
handling the key.
WARNING
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 17

18
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Type of key
Spare
mechanical
key
Main keywith remote control
Direction indicators flashing
(only when key
has remote control)
Deterrence led
Pressing button Ëactivates opening of the fuel flap.
The main functions that can be activated with the keys (with or without remote control) are the following:
Door locking
from the outside
Turn the key
clockwise
(driver’s side)
Turn the key
clockwise
(driver’s side)
Short pressing of
buttonÁ
blinks once
Steady for
approximately 3 seconds
and then
deterrent blinkingUnlocking the
tailgate
Prolonged button pressing
(for over 2 seconds) R
blinks twice
Deterrence led Door lock release
Turn the key
anticlockwise
(driver’s side)
Turn the key
anticlockwise
(driver’s side)
Short pressing
of button Ë
blinks twice
Switching off
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 18

21
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INSTRUMENTS
SPEEDOMETER fig. 22
It shows the car speed.
REV. COUNTER fig. 23
It shows the engine revolutions per
minute.
IMPORTANT The electronic injection
control system gradually shuts off the
flow of fuel when the engine is “over-
revving”, thus causing a gradual loss
of engine power.
When the engine is idling, the rev
counter may indicate a gradual or
sudden increase of the speed.
This is normal and does not indicate
a fault. It may be caused, for exam-
ple, by the operation of the climate
control system or fan. In these cases,
a slow change in engine speed is used
to protect the battery charge.The reserve warning light Aturns on
to indicate that approximately
6 litres of fuel are left in the tank.
Do not travel with the tank nearly
empty: lack of fuel supply could dam-
age the catalyser. FUEL LEVEL GAUGE fig. 24
This gauge gives an indication of the
litres of fuel in the tank (see the in-
formation provided in paragraph “Re-
fuelling the car”).
fig. 22L0D0241mfig. 24L0D0023m
fig. 23L0D0242mfig. 25L0D0024m
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 21

24
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Setting the unit
To set the required unit (kilometres or
miles) proceed as follows:
❒press the button MODEseveral
times until the text “Unit” ap-
pears;
❒press the button +or–to change
the unit;
❒press the button MODEand hold
it pressed for over 2 seconds to
confirm the unit setting.
V iewing of the
fuel cut-off inertial switch
tripping
The screen automatically appears
whenever the fuel cut-off inertial
switch trips after a significant colli-
sion.
This switch stops fuel supply.
See the information provided in the
dedicated chapter “Fuel cut-off iner-
tial switch”. Set this function as follows:
❒press the button MODEseveral
times until the text “SPEED” ap-
pears;
❒press the button +to increase the
speed value (max. limit being 250
Km/h);
❒press the button –to reduce the
speed value (min. limit being 30
Km/h below which the system
goes back to “OFF” mode);
❒press the button MODEand hold
it pressed for over 2 seconds to
confirm the speed setting.
If, after the message
“FPSon” appears, you
smell fuel or see leaks from the fuel
supply system, do not reset the
switch to avoid the risk of starting a
fire.
WARNING
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 24