LAND ROVER DEFENDER 1999 Workshop Manual

ProCarManuals.com

COOLING SYSTEM
1
ADJUSTMENT DRAIN AND REFILL
Service repair no - 26.10.01
WARNING: Hot coolant
Drain
1.Remove engine acoustic cover.
2.Visually check engine and cooling system for
signs of coolant leaks.
3.Examine hoses for signs of cracking, distortion
and security of connections.
4.Position drain tray to collect coolant.
5.Remove expansion tank filler cap.
6.Loosen clip screws securing air inlet hose to
intercooler and inlet manifold, release and
remove hose.
7.Release clip and disconnect bottom hose from
radiator.
8.Allow cooling system to drain.
9.Disconnect bottom hose from radiator.Refill
1.Flush system with water under low pressure.
2.Do not use water under high pressure as it could
damage the radiator.
3.Connect bottom hose to radiator and secure
hose with clip.
4.Prepare coolant to required concentration.
5.Position heater temperature control to maximum
hot position.
6.Remove bleed screw from top hose.
7.Fill system slowly through coolant expansion
tank until a steady flow of coolant is emitted from
the bleed hole in top hose.
8.Fit bleed screw to top hose.
9.Continue filling system until coolant level
reaches’MAX’mark on expansion tank.
10.Fit expansion tank filler cap.
11.Position air intake hose and tighten clip screws.
12.Start and run engine until normal running
temperature is reached.
13.If fitted, DO NOT operate air conditioning.
14.Switch off engine and allow to cool.
15.Check for leaks and top-up coolant to’MAX’
mark on expansion tank.
ProCarManuals.com

ProCarManuals.com

COOLING SYSTEM
1
REPAIR COUPLING - COOLING FAN
Service repair no - 26.25.19
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Remove cooling fan cowl.
NOTE: Thread is RH.
5.Remove cooling fan usingLRT-12-093and
LRT-12-094.
Refit
6.Position cooling fan and tighten using
LRT-12-093andLRT-12-094.
7.Fit cooling fan cowl.
8.Fit engine acoustic cover.
9.Reconnect battery negative lead.
10.Fit battery cover.THERMOSTAT
Service repair no - 26.45.09
Remove
1.Drain cooling system.See Adjustment.
2.Remove cooling fan.See this Section.
3.Release 3 clips and disconnect coolant hoses
from thermostat.
4.Remove thermostat.
Refit
5.Position thermostat, connect hoses and secure
with clips.
6.Fit cooling fan.See this Section.
7.Fill cooling system.See Adjustment.
ProCarManuals.com

26COOLING SYSTEM
2
REPAIR PUMP - COOLANT
Service repair no - 26.50.01
Remove
1.Drain cooling system.See Adjustment.
2.Remove centrifuge.See ENGINE , Repair.
3.Release clip and hose from coolant pump cover.
4.Remove 5 bolts securing coolant pump cover.
5.Remove cover and coolant pump from housing
and discard’O’rings.Refit
6.Clean coolant pump housing and mating faces.
7.Fit new’O’rings to coolant pump and cover.
8.Fit coolant pump and cover and tighten bolts to9
Nm (7 lbf.ft).
9.Connect hose to pump cover and secure clip.
10.Refit centrifuge.See ENGINE , Repair.
11.Refill cooling system.See Adjustment.
ProCarManuals.com

COOLING SYSTEM
3
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Remove front grille.See CHASSIS AND
BODY, Repair.
2.Drain cooling system.See Adjustment.
3.Remove cooling fan.See this Section.
4.Remove 5 bolts and move bonnet platform
aside.
5.Release clip and disconnect bleed hose from
radiator.
6.Release clip and disconnect top hose from
radiator.
7.Release clip and disconnect fuel cooler hose
from radiator.
8.Release clip and disconnect coolant rail hose
from radiator.
ProCarManuals.com

26COOLING SYSTEM
4
REPAIR
9.Remove 4 bolts securing RH and LH radiator
mounting brackets to body and remove brackets.
10.Release clip and release air hose from
turbocharger inlet pipe.11.Release bottom hose from bracket on lower
cooling fan cowl.
12.Remove radiator assembly and collect lower
mounting spacers.
13.Remove 2 bolts and remove intercooler from
radiator. Collect 2 nuts from radiator side
brackets.
14.Remove 2 rubber mountings from intercooler.
15.Remove 2 screws and remove lower cooling fan
cowl from radiator.
16.Remove 2 rubber mountings from bottom of
radiator.
ProCarManuals.com

COOLING SYSTEM
5
REPAIR Refit
17.Fit rubber mountings to bottom of radiator.
18.Fit lower cooling fan cowl to radiator and secure
with screws.
19.Fit nuts to radiator side brackets.
20.Position intercooler to radiator and tighten bolts.
21.Fit rubber mountings to intercooler.
22.Position mounting spacers and fit radiator.
23.Fit bottom hose into bracket on lower cooling fan
cowl.
24.Position air hose to turbocharger pipe and
secure with clip.
25.Position LH and RH radiator mounting brackets
to body and radiator and tighten bolts.
26.Position coolant rail hose to radiator and secure
with clip.
27.Position fuel cooler hose to radiator and secure
with clip.
28.Position top hose to radiator and secure with
clip.
29.Position bleed hose to radiator and secure with
clip.
30.Position bonnet platform and tighten bolts.
31.Fit cooling fan.See this Section.
32.Fit front grille.See CHASSIS AND BODY,
Repair.
33.Fill cooling system.See Adjustment.
ProCarManuals.com

ProCarManuals.com

30 - MANIFOLD AND EXHAUST SYSTEM
CONTENTS
Page
DESCRIPTION AND OPERATION
MANIFOLD COMPONENT LAYOUT 1...................................................................
DESCRIPTION 2.....................................................................................................
REPAIR
PIPE - EXHAUST - FRONT 1.................................................................................
SILENCER - INTERMEDIATE 2.............................................................................
EXHAUST - TAIL PIPE AND SILENCER 3.............................................................
GASKET - INLET MANIFOLD 3..............................................................................
GASKET - EXHAUST MANIFOLD 5.......................................................................
ProCarManuals.com