LAND ROVER DISCOVERY 1995 Workshop Manual

V8i
13
REPAIR
NOTE: Release bolts securing compressor
mounting bracket to engine and remove
bracket to enable temporary lifting eye
ETC 5964 to be fitted. Secure lifting eye to
mounting bracket fixing points with suitable bolts
of equivalent size, pitch and thread. Leave lifting
eye attached until engine is reinstalled in vehicle.
15.Place drain tray underneath vehicle.
16.Disconnect hose from reservoir to power
steering pump. Secure hose end above level of
fluid reservoir to avoid unnecessary loss of fluid.
17.Disconnect power steering pump to power
steering box hose. Seal hose and pump
openings with masking tape to prevent ingress of
dirt. Wipe away any fluid spillage from chassis or
steering box.
18.Disconnect fuel temperature and coolant
temperature sensor multi-plugs.
19.Disconnect leads from coil.
20.Identify each injector multi-plug for re-assembly
and disconnect plugs from injectors.
21.Manoeuvre harness from behind fuel rails and
place to one side clear of engine assembly.
22.Remove two clamps securing gearbox oil cooler
pipes to engine block.
23.Remove engine mounting fixings on both sides
of cylinder block.
24.Fit lifting chains to engine lifting eyes as shown
in illustration RR1780E.
1. L/H Front chain 356mm total overall length.
2. R/H Front chain 330mm total overall length.
3. R/H Rear chain 457mm total overall length.
NOTE: All chain dimensions are measured
from end of lifting hook to end of last link
in chain.
25.Fit chain lifting eye to a suitable engine hoist.
Raise hoist high enough to enable engine
mountings to be removed, and withdraw rubber
mountings.
26.Lower hoist until engine rests securely on engine
mounting brackets. Remove lifting chains and
hoist.
27.Disconnect two heater hoses located on top of
right hand rocker cover.
28.Remove ground strap from rear of left hand
cylinder head. DO NOT remove from retaining
clip.
29.Remove all electrical harnesses from retaining
clips at rear of engine.
30.Remove transmission breather pipes from
retaining clip on rear lifting eye.
31.Remove top two bolts securing bell housing to
cylinder block.
32.Raise front of vehicle, lower vehicle on to axle
stands.
33.Remove bell housing bottom cover. Remove
gasket from bell housing face.
34.Remove nuts securing exhaust downpipes to
manifolds, remove heat shield from right hand
side downpipe.
35.Remove electrical leads from starter motor
solenoid. Disconnect multi-plug from oil level
sensor on side of sump, if fitted.
NOTE: Instructions 37, 38 and 39 refer to
automatic vehicles only.
36.With assistance rotate engine at crankshaft
pulley until two access holes in drive plate/ring
gear assembly are visible.
37.Remove two bolts visible through access holes.
Mark one access hole and one bolt hole to
ensure unit is reassembled in its original position
38.Rotate crankshaft 180Ê until two remaining
access holes are visible, remove two bolts.

12ENGINE
14
REPAIR
39.Remove remaining bell housing to cylinder block
bolts.
40.Remove starter motor ground strap from
chassis.
41.Remove stands and lower vehicle.
42.Position hydraulic trolley jack under bell housing
to support gearbox when engine and gearbox
are separated.
43.Fit lifting chains to engine. Carefully raise hoist a
little, ease engine and gearbox apart, steady
engine on hoist.
44.Ensure no components remain that will prevent
engine being removed.
45.Slowly raise engine clear of engine
compartment. Move engine away from vehicle
and place on a suitable engine stand.
Refit
46.Fit lifting chains to engine. Raise engine using
hoist.
47.Lower engine into engine compartment. Ensure
all components are clear of engine assembly.
48.Automatic vehicles: With assistance, manoeuvre
engine until bottom two engine and bellhousing
bolt holes align. Ensure that two cylinder block
dowels locate in bell housing.
Manual vehicles: Lower engine into position.
Locate primary pinion into clutch. Engage bell
housing dowels.
49.Fit two bolts and partially tighten.
50.Remove jack and lower hoist until engine rests
securely on engine mounting brackets.
51.Fit top two bell housing securing bolts. Tighten
to
40 Nm.
52.Fit remaining bell housing to cylinder block bolts.
Tighten to
40 Nm.
53.Automatic vehicles: With assistance, rotate
crankshaft pulley, line up marked holes in drive
plate and torque converter. Fit two bolts.
Tighten to
40 Nm.
54.Rotate crankshaft 180°and fit remaining two
bolts tighten to correct torque,
40 Nm.
55.Fit new gasket and refit bottom cover, tighten
bolts to
9 Nm.
56.Fit new exhaust flange gaskets, fit exhaust to
manifold.
57.Refit all harnesses, ground straps breather pipes
and hoses at rear of engine.
58.Raise engine and refit engine mounting rubbers,
tighten nuts to
20 Nm.
59.Remove temporary lifting eye ETC 5964 and
reverse instructions 1 to 23, ensuring that all
electrical plugs and harnesses are fitted in
correct locations.

V8i
15
REPAIR OIL SUMP
Service repair no - 12.60.44
Remove
1.Drain engine oil
See SECTION 10,
Maintenance, Under Vehicle Maintenance
2.Fit drain plug. Tighten to40 Nm.
3.If fitted, disconnect low oil level sensor multiplug.
4.Remove bolt securing dipstick tube to rocker
cover.
5.Working form the centre outwards, progressively
loosen and remove 17 bolts securing sump.
Remove sump.
6.Remove all traces of sealant from mating
surfaces of sump, cylinder block and front cover,
using a suitable solvent or plastic scraper.
7.Degrease mating surfaces of sump, cylinder
block and front cover.Refit
8.Apply RTV Hylosil White sealant to mating
surface of sump.
9.Position sump, tighten bolts finger tight.
10.Tighten bolts progressively in sequence shown.
Tighten to
18 Nm.
11.Fit bolt securing dipstick tube to rocker cover.
12.If fitted, connect low oil level sensor multiplug.

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine
Adaptor plate to crankshaft 84........................................................................
Generator and power steering mounting bracket to cylinder head 30............
Cylinder head:
Stage 1: 20.............................................................................................
Stage 2: - Further 180°±5°
Drive plate to converter 39..............................................................................
Engine mountings to engine and chassis 55..................................................
Engine mounting rubbers to brackets 30........................................................
Flexible drive plate to crankshaft adaptor plate 41.......................................... **
Flywheel to crankshaft bolts 78....................................................................... **
Lifting eye to cylinder heads 39......................................................................
Main bearing cap rear bolts 92....................................................................... *
Oil sump drain plug 40....................................................................................
Oil sump to cylinder block 18..........................................................................
Rocker cover to cylinder head 9....................................................................
Rocker shaft bracket to cylinder head 38........................................................
Spark plug 21..................................................................................................
Starter motor attachment 44...........................................................................
* These bolts must have threads coated in lubricant EXP16A before assembly.
** These bolts must have threads coated in sealant Loctite 270
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
NOTE: Torque values above are for all screws and bolts used except for those specified.

V8i
1
SERVICE TOOLS ENGINE
LRT-12-034 Spring compressor
MS1519A
LRT-12-010 Crankshaft rear seal guide
RO1014
LRT-12-052 Oil pressure test kit

4.0 V8
1
DESCRIPTION AND OPERATION DESCRIPTION
For description and operation refer to overhaul
manual 4.0/4.6 V8 engine.
CONTENT OF THIS SECTION
Only service repair operations not covered in engine
section V8i or unique to 4.0 V8 engines appear in the
repair sub-section of this section.

4.0 V8
1
REPAIR CRANKSHAFT PULLEY
Service repair no - 12.21.01 - Crankshaft Pulley
Remove
1.Disconnect battery negative lead.
2.Remove cooling fan.
See COOLING SYSTEM,
Repair, Viscous Coupling, Fan Blades,
Pulley and Fan Cowl
3.Slacken 3 water pump pulley securing bolts.
4.Remove drive belt.
See ENGINE 3.9 V8,
Repair, Drive Belt Renew
5.Remove water pump pulley bolts. Remove water
pump pulley.
6.Raise and support front of vehicle.
7.Remove 9 bolts securing bell housing access
cover (2 dowel bolts).
8.Remove access plate.
NOTE: It will be necessary to have an
assistant position a large flat ended
screwdriver between ring gear and adaptor
plate to prevent ring gear rotating.
9.Remove crankshaft pulley bolt. Collect pulley
and tool.
Refit
10.Clean seal running surface on pulley.
11.Clean key and keyway.
12.Fit crankshaft pulley.
NOTE: It will be necessary to have an
assistant position a large flat ended
screwdriver between ring gear and adaptor
plate to prevent ring gear rotating.
13.Refit crankshaft pulley bolt. Tighten to
270 Nm.
14.Ensure mating faces between bell housing
access cover and mating face are clean.
15.Fit access cover.
16.Fit cover bolts. Tighten to
10 Nm.
17.Remove supports and lower vehicle.
18.Ensure mating faces between water pump pulley
and pump are clean.
19.Refit water pump pulley. Fit bolts finger tight.
20.Fit drive belt.
See ENGINE 3.9 V8, Repair,
Drive Belt Renew
21.Tighten water pump pulley bolts to Tighten to24
Nm.
22.Refit cooling fan.See COOLING SYSTEM,
Repair, Viscous Coupling, Fan Blades,
Pulley and Fan Cowl
23.Reconnect battery negative lead.

12ENGINE
2
REPAIR CRANKSHAFT FRONT OIL SEAL
Service repair no - 12.21.14 - Crankshaft Front Oil
Seal
Remove
1.Remove crankshaft pulley.
See ENGINE 3.9 V8,
Repair, Crankshaft Pulley Assembly
2.Screw tool LRT-12-088 into oil seal.
3.Turn centre bolt of tool to extract oil seal.
4.Remove oil seal from tool.
Refit
5.Clean seal seating and pulley seal register.
6.Lubricate seal with oil.
7.Locate oil seal in housing and drive into place
using LRT-12-089.
8.Lubricate oil seal lip.
9.Locate seat in front cover.
10.Drift seat into position using tool LRT-12-089.
11.Refit crankshaft pulley.
See ENGINE 3.9 V8,
Repair, Crankshaft Pulley Assembly; Refit

4.0 V8
3
REPAIR ENGINE ASSEMBLY
Service repair no - 12.41.01/99
Remove
1.Position vehicle on ramp.
2.Remove bonnet.
See CHASSIS AND BODY,Repair, Bonnet [Hood]
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator
4.Remove plenum chamber.See FUEL SYSTEM
SFI, Repair, Plenum Chamber
5.Remove mass air flow sensor.See FUEL
SYSTEM SFI, Repair, Mass Air Flow Sensor
(MAF Sensor)
6.Slacken hose clip securing bottom hose to
expansion tank.
7.Disconnect hose.
8.Remove 2 nuts securing expansion tank.
9.Remove nut and bolt securing expansion tank.
10.Remove expansion tank.
11.Disconnect servo vacuum hose from ram
housing.
12.Disconnect battery sensing lead Lucar from
generator.
13.Remove generator terminal cover.
14.Remove 2 terminal nuts and release leads from
terminals.
15.Release purge hose from ram pipe housing.
16.Position cloth to absorb fuel spillage.
17.Slacken clip securing fuel return hose to fuel rail.
18.Disconnect hose.
19.Plug connections.
20.Disconnect fuel feed hose union.
21.Plug connections. Position hoses aside.
22.Slacken clip securing heater return hose to pipe.
23.Disconnect hose.24.Slacken clip securing heater feed adaptor hose
to inlet manifold.
25.Remove bolt securing pipe bracket.
26.Disconnect feed hose from inlet manifold.
27.Disconnect hose/pipe assembly.
28.Disconnect leads from spark plugs and remove
ignition coils.
See FUEL SYSTEM SFI, Repair,
Ignition Coils
29.Disconnect fuel temperature sensor multiplug.
30.Disconnect coolant sensor multiplug.
31.Disconnect temperature gauge sensor lead.
32.Release camshaft sensor multiplug from bracket
and disconnect multiplug.
33.Disconnect oil pressure switch Lucar.
34.Disconnect air intake temperature sensor
multiplug.
35.Disconnect 8 injector multiplugs.
36.Remove 4 nuts securing harness brackets to
inlet manifold.
37.Release harness brackets.
38.Remove bolts securing gearbox breather pipes
to engine lifting bracket.

12ENGINE
4
REPAIR 39.Release battery positive lead terminal cover.
40.Remove terminal nut
41.Release terminal from battery.
42.Release fusebox main feed lead.
43.Position battery cable over engine.
44.Pivot jockey pulley downwards to release drive
belt tension.
45.Release belt from pulleys.
46.Remove drive belt.
47.Disconnect compressor multiplug
48.Remove 4 bolts securing compressor.
49.Remove heatshield.
50.Release compressor from bracket and tie aside.
51.Slacken clip securing PAS hose to pump.
52.Disconnect hose.
53.Plug hose and pump.
54.Disconnect PAS hose connection at pump and
steering box.
55.Release unions and remove hose.
56.Remove and discard 'O' rings.
57.Plug pump and steering box.
58.Remove LH and RH engine mounting nuts.
59.Position lifting chains and attach hooks to engine
lifting eyes.
60.Raise engine sufficiently to release engine
mountings.
61.Release engine mountings and remove.
62.Lower engine until it just rests on engine
mounting brackets.
63.Disconnect chains.
64.Raise ramp.
65.Remove catalytic converter/front pipe assembly.
See EMISSION CONTROL, Repair, Catalytic
Converter/Front Pipe - 4.0 V8
66.Remove 9 bolts securing bell housing bottom
cover. Note position of 2 dowel bolts.
67.Remove cover.
68.Remove locknut securing transfer box tie bar.
69.Remove 2 bolts securing tie bar to tranmission.
70.Remove tie bar.
71.Remove 2 and slacken 1 bolt, securing bell
housing access plate and position aside.
72.Mark drive plate to torque converter relationship.
73.With assistance, rotate crankshaft for access to
first bolt (torque converter to drive plate).
74.Remove first bolt.
75.Repeat steps for the remaining 3 bolts.
76.Remove 2 bolts securing crankshaft sensor
shield to engine backplate.
See FUEL SYSTEM
SFI, Repair, Crankshaft Position Sensor
(CKP Sensor)