sensor LAND ROVER DISCOVERY 1995 Workshop Manual

30MANIFOLD AND EXHAUST SYSTEM
10
REPAIR 10.Release clip and disconnect breather hose from
manifold.
11.Release 2 bolts securing camshaft cover
brackets to manifold.
12.Disconnect 4 vacuum hoses from manifold.
13.Remove 6 bolts securing manifold chamber to
lower manifold.
14.Remove manifold chamber and collect gaskets.
Refit
NOTE: For torque values.See
Specifications, torque, Torque Values
15.Ensure mating faces of manifold chamber and
lower manifold are clean.
16.Fit a new gasket, position manifold chamber to
lower manifold.
17.Fit bolts, tighten to the correct torque.
18.Connect vacuum hoses to manifold.
19.Position camshaft cover brackets to manifold,
secure with bolts.
20.Connect breather hose and brake servo hose to
manifold, secure with clips.
21.Connect multiplug to fuel temperature sensor.
22.Connect breather hose to throttle housing and
secure with clip.
23.Connect throttle cable to cam and secure to
abutment bracket.
24.Connect coolant bypass hose to throttle housing.
25.Connect stepper motor and throttle
potentiometer multiplugs.
26.Connect air cleaner hose to throttle housing and
secure with clip.
27.Reconnect battery negative lead.
28.Adjust throttle cable.

41TRANSFER GEARBOX
2
REPAIR Remove
1.Site vehicle on a ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl from radiator.
4.Remove transfer gear lever knob and gaiter.
5.Raise vehicle on ramp [hoist].
6.Drain oil and refit plug.
7.Detach heat shield at front exhaust pipe to
manifold.
8.Disconnect electrics to Lambda sensors.
9.Remove catalytic converter assembly.
10.Remove chassis crossmember from under
gearbox.
11.Remove heat shield from speedometer cable at
transfer gearbox.
12.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
13.Mark for reassembly then disconnect propeller
shaft to output flange, tie to one side.
14.Repeat on front propeller shaft to output flange.
15.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
16.Place four 30mm long spacers between top of
hoist and adaptor plate, at securing points, and
secure adaptor plate to hoist.17.Remove four central bolts from transfer gearbox
bottom cover, move hoist into position and
secure adaptor plate to transfer gearbox.
18.Adjust hoist to take weight of transfer gearbox.
19.Remove tie bar, transfer gearbox to main
gearbox.
20.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
21.Repeat for left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket.
22.Remove right side mounting bracket to flexible
mounting rubber.
23.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
24.Loosen park brake adjustment nut.
25.Remove park brake drum.
26.Remove park brake assembly complete from
rear output flange.
27.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
28.Remove banjo bolt from breather pipe, retrieve
sealing washers and lay pipe aside.
29.Remove split [cotter] pin and washers securing
differential lock to connecting rod and disconnect
rod from lever.
30.Select low range transfer gearbox position.
31.Remove high/low rod lower lock nut and remove
rod from yoke.
32.Position hoist jack channel under bell housing.
33.Using wooden block support the main gearbox
and bell housing.
34.Remove upper and lower bolts securing transfer
gearbox to main gearbox.
35.Fit guide studs 18G 1425 to main gearbox and
move transfer gearbox rearwards to detach.

44AUTOMATIC GEARBOX
2
REPAIR 1.Site vehicle on a four post ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl securing screws and release
cowl from radiator.
4.Loosen securing clip and disconnect air flow
hose from plenum chamber.
5.Disconnect stepper motor hose from top of
plenum chamber.
6.Disconnect kickdown cable from throttle linkage
and release from clipping.7.Release two gearbox breather pipes from clip
located on lifting eye at rear of right hand
cylinder head.
8.Remove dipstick from main gearbox oil filler
tube.
9.Working inside vehicle detach transfer gear lever
gaiter from console, unscrew knob and withdraw
gaiter and knob.
10.Raise vehicle on ramp [hoist].
11.Remove drain plugs and drain oil from transfer
gearbox and main gearbox. Refit plugs.
12.Detach heat shield at front exhaust pipe to
manifold.
13.Disconnect electrics to Lambda sensors.
14.Remove catalytic converter assembly.
15.Remove chassis cross-member from under
gearbox.16.Remove heat shield from speedometer cable at
transfer gearbox.
17.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
18.Mark for reassembly propeller shaft to transfer
gearbox mating flanges.

ZF
3
REPAIR 19.Disconnect rear propeller shaft to output flange,
and tie to one side.
20.Repeat instructions 18 and 19 on front propeller
shaft to main gearbox.
21.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
22.Disconnect oil cooler feed and return pipes from
bottom and side of main gearbox.
23.Release cooler pipes from clamp at engine sump
and remove distance piece.
24.Blank pipe ends and unions.
25.Move oil cooler pipes clear of transmission and
tie aside.
26.Disconnect selector cable from operating lever.
27.Disconnect inhibitor switch at multiplug.
28.Attach adaptor plate to hoist.
29.Remove two bolts from transfer gearbox rear
cover.
30.Raise hoist to align adaptor plate with transfer
gearbox and transmission. Secure to transfer
gearbox at rear cover with two bolts removed.
31.Adjust hoist to take weight of transmission.
32.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
33.Repeat for the left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket
34.Remove right side mounting bracket to flexible
mounting rubber retaining nut.
35.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
36.Remove clip and clevis pin from park brake
lever.
37.Remove clip securing outer brake cable
38.The park brake cable is now free.
39.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
40.Remove ties securing breather pipes to harness.
41.Remove bell housing access plate complete with
gasket.
42.Rotate engine, using crankshaft pulley, until two
access holes are visible in drive plate/ring gear
assembly through bell housing bottom cover
opening.
43.Identify an access hole and bolt hole to aid
reassembly.
44.Remove bolts securing drive plate to convertor
through access holes.
45.Rotate crankshaft half turn to access and
remove remaining bolts.
46.Disconnect oil dipstick tube at main gearbox.
47.Remove bolt at bell housing and detach dipstick
tube. Blank pipe end and union.
48.Position hoist jack channel under engine and
support using a wooden block.
49.Remove bell housing to engine securing bolts,
also detach harness bracket from bell housing.
50.Ease transmission rearwards to allow access to
secure torque converter in bell housing.
51.Lower hoist and complete removal of
transmission.
Refit
52.Ensure torque converter is retained in bell
housing.
53.Secure transmission to adaptor plate on lifting
hoist.
54.Raise hoist and locate transmission with engine.
55.Remove torque converter retainer.
56.Complete attachment of transmission to engine
and fit bell housing bolts. Fit the dipstick tube
bracket and harness bracket to their respective
bolts.
57.Complete refitting by reversing removal
procedure. Note the following important points.
58.Drive plate to torque converter bolts are to be
coated with Loctite 290 prior to assembly.
59.Refill transfer and main gearboxes with correct
grade oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
60.Check operation of parking brake and adjust as
necessary.
See SECTION 10, Maintenance,
Vehicle Interior

44AUTOMATIC GEARBOX
8
REPAIR INHIBITOR SWITCH
Service repair no - 44.15.19
Remove
1.Site vehicle on a four post ramp [hoist].
2.Disconnect battery negative lead. Raise vehicle.
3.Disconnect inhibitor switch multi plug.
4.Remove inhibitor switch retaining plate.
5.Remove inhibitor switch.
6.Remove 'O' ring seal.
7.Clean inhibitor switch.
Refit
8.Clean mating face on casing.
9.Fit and lubricate new 'O' ring seal to switch.
10.Fit switch to casing.
11.Secure with retaining plate and bolt.
12.Connect multiplug to harness.
13.Reconnect battery and remove vehicle from
ramp [hoist].
SELECTOR SHAFT OIL SEAL
Service repair no - 44.15.34
Renew
1.Site vehicle on a four post ramp [hoist].
2.Disconnect battery negative lead.
3.Raise vehicle.4.Detach heat shield at front exhaust pipe to
manifold.
5.Disconnect electrics from Lambda sensors.
6.Remove catalytic converter assembly.
7.Remove chassis cross-member from under
gearbox.
8.Engage low range gear in the transfer gearbox.
9.Support transfer gearbox with a jack or
transmission hoist.
10.Remove transfer gearbox chassis mounting
bracket nuts and bolts. Note location of
speedometer cable bracket for refit.
11.Lower transmission to allow access to selector
shaft.
12.Remove selector lever from shaft.
13.Remove selector shaft seal from casing.
14.Clean selector shaft and seal mating faces.
15.Fit centre section of special tool LST 114 over
selector shaft.
16.Lubricate new oil seal and position seal on tool.
17.Fit tool outer sleeve and screw on nut to drive
seal into housing.
18.Remove tool from shaft.
19.Refit selector lever to shaft.
20.Raise transmission and secure mounting
brackets to chassis. Ensure speedometer cable
bracket is secured. Tighten bolts to
30Nm.
21.Remove support jack.
22.Refit chassis cross-member.
23.Refit catalytic converter assembly.
24.Connect electrics to Lambda sensors.
25.Connect heat shield front pipe to manifold.
26.Connect battery.
27.Check/top up gearbox oil level.

ZF
9
REPAIR OIL SUMP
Service repair no - 44.24.05
Remove
1.Site vehicle on a four post ramp [hoist].
2.Disconnect battery negative lead.
3.Raise vehicle.
4.Drain oil and refit plug with new seal.
5.Detach heat shield at front exhaust pipe to
manifold.
6.Disconnect electrics from Lambda sensors.
7.Remove catalytic converter assembly.
8.Remove chassis cross-member from under
gearbox.
9.Disconnect dipstick tube at oil sump. Loosen
securing bolt at bell housing and move dipstick
aside.
10.Remove clamps securing oil sump. Note their
locations for refit and withdraw sump.
11.Remove gasket and clean gasket mating faces.Refit
12.Refit oil sump using a new gasket.
13.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
14.Refit chassis cross member.
15.Refit catalytic converter assembly
16.Connect electrics to Lambda sensors.
17.Connect heat shield front pipe to manifold.
18.Connect battery.
19.Refill gearbox using correct grade of oil.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids

44AUTOMATIC GEARBOX
10
REPAIR OIL SCREEN
Service repair no - 44.24.07
Renew
1.Site vehicle on a four post ramp [hoist].
2.Disconnect battery negative lead.
3.Raise vehicle.
4.Drain oil and refit plug with new seal.
5.Detach heat shield at front exhaust pipe to
manifold.
6.Disconnect electrics from Lambda sensors.
7.Remove catalytic converter assembly.
8.Remove chassis cross-member from under
gearbox.
9.Disconnect dipstick tube at oil sump. Loosen
securing bolt at bell housing and move dipstick
aside.
10.Remove clamps securing oil sump. Note their
locations for refit and withdraw sump.
11.Remove gasket and clean gasket mating faces.
12.Remove securing screws and detach oil screen
and suction pipe, taking care to retain suction
pipe spacer, discard 'O' ring seal.13.Detach suction pipe from oil screen, discard 'O'
ring seal.
14.Clean oil screen and blow out with airline.
15.Clean suction pipe.
16.Fit new 'O' ring seals to oil screen using light
grease to aid assembly.
17.Fit oil screen and suction pipe with spacer and
secure with three bolts.
18.Refit oil sump using a new gasket.
19.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
20.Refit chassis cross-member.
21.Refit catalytic converter assembly
22.Connect electrics to Lambda sensors.
23.Connect heat shield front pipe to manifold.
24.Connect battery.
25.Refill gearbox oil system using correct grade of
oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

ZF
11
REPAIR CONTROL UNIT
Remove
1.Site vehicle on a four post ramp [hoist].
2.Disconnect battery negative lead.
3.Raise vehicle.
4.Drain oil and refit plug with new seal.
5.Detach heat shield at front exhaust pipe to
manifold.
6.Disconnect electrics from Lambda sensors.
7.Remove catalytic converter assembly.
8.Remove chassis cross-member from under
gearbox.
9.Disconnect dipstick tube at oil sump. Loosen
securing bolt at bell housing and move dipstick
aside.
10.Remove clamps securing oil sump. Note their
locations for refit and withdraw sump.
11.Remove gasket and clean gasket mating faces.
12.Remove securing screws and detach oil screen
and suction pipe, taking care to retain suction
pipe spacer, discard 'O' ring seal.
13.Remove securing screws and detach control unit
from casing.

44AUTOMATIC GEARBOX
12
REPAIR Oil seal replacement
14.Remove circlips and springs from control unit.
Note locations of long and short springs.
15.Using seal replacer/remover LST113 remove
and discard seals.
16.Clean control unit, springs and circlips and check
that they are satisfactory for further use.
17.Fit new seals to control unit using LST113,
ensure seals are fully seated.
18.Fit springs to locations noted during removal and
secure with circlips.
Refit
19.Fit control unit to gearbox, locating throttle valve
behind cam and engaging selector quadrant with
manual valve.
20.Loosely fit securing screws.21.Manually open throttle linkage to full throttle
position.
22.Engage special tool LST 109 between control
unit and throttle valve pin.
23.Set correct distance between control unit and
cam.
24.Remove special tool and close throttle.
25.Fit new 'O' ring seals to oil screen using light
grease to aid assembly.
26.Fit oil screen and suction pipe with spacer and
secure with three bolts.
27.Refit oil pan using a new gasket.
28.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
29.Refit chassis cross member.
30.Refit catalytic converter assembly
31.Connect electrics to Lambda sensors.
32.Connect heat shield front pipe to manifold.
33.Connect battery.
34.Refill gearbox oil system using correct grade of
oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

ZF
13
REPAIR KICKDOWN CABLE
Service repair no - 44.15.01
Remove
1.Site vehicle on a four post ramp [hoist].
2.Select neutral 'N' gear lever.
3.Disconnect battery negative lead.
4.Disconnect kickdown cable at throttle linkage.
5.Release outer cable locknut.
6.Disconnect cable from mounting bracket.
7.Release cable from bracket attached to cylinder
head.
8.Feed cable through to underside of vehicle.
9.Raise vehicle on ramp [hoist].
10.Drain oil and refit plug with new seal.
11.Detach heat shield at front exhaust pipe to
manifold.
12.Disconnect electrics from Lambda sensors.
13.Remove catalytic converter assembly.
14.Remove chassis cross-member from under
gearbox.
15.Disconnect dipstick tube at oil sump. Loosen
securing bolt at bell housing and move dipstick
aside.
16.Remove clamps securing oil sump. Note their
locations for refit, and withdraw sump.
17.Pull kickdown inner cable to fully open valve
cam. Wedge cam in this position.
18.Release cable from cam by pushing inner cable
into outer casing and detaching cable nipple
from cam.
19.Using special tool LST112 compress cable tangs
and remove cable from gearbox.
20.If cable is to be refitted remove 'O' ring seal and
clean cable assembly.
Refit
21.Fit new 'O' ring seal to cable and lubricate seal.
22.Fit cable to gearbox casing ensuring it is
correctly seated.
23.Fit inner cable nipple to its location on cam.
NOTE: When a new cable is fitted, to help
locate nipple to cam, introduce a curve
into the cable. Do not bend or kink cable.24.Remove wedge from cam and ensure nipple
remains engaged.
25.Feed free end of cable assembly into engine
compartment.
26.Refit oil pan using a new gasket.
27.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
28.Refit chassis cross-member
29.Refit catalytic converter assembly
30.Connect electrics to Lambda sensors.
31.Connect heat shield front pipe to manifold.
32.Lower vehicle on ramp [hoist].
33.Fit cable to bracket at cylinder head.
34.Locate cable in mounting bracket, do not tighten
locknut.
35.Fit cable to throttle linkage.
36.Ensure throttle linkage is fully closed.
37.Adjust outer cable to achieve a gap of 0,25 to
1,25mm (dimension 'A') between end of outer
cable and crimped collar on inner cable.
38.Tighten locknuts and recheck gap.
NOTE: If fitting a new cable, and collar on
inner cable is loose, measure distance 'B'
on old cable. Crimp collar on new cable to
this dimension.
39.Reconnect battery negative lead.
40.Refill gearbox oil using correct grade of oil.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids