sensor LAND ROVER DISCOVERY 1995 Owners Manual

SFI
13
REPAIR PLENUM CHAMBER
Service repair no - 19.22.46
Remove
1.Disconnect battery negative lead.
2.Slacken clip securing intake hose to plenum
chamber and release hose.
3.Remove split pin from throttle cable clevis pin.
4.Remove clevis pin.
5.Release and remove kick down cable clevis pin.
6.Disconnect vacuum hose from cruise actuator.
7.Release throttle cable from abutment bracket.
8.Remove front locknut from kick down cable.9.Release cable from bracket.
10.Disconnect breather hose from plenum.
11.Release clip and disconnect multiplug from
throttle position sensor (TP Sensor).
12.Disconnect multiplug from idle air control (IAC).
13.Remove 6 bolts securing plenum chamber.
14.Release plenum chamber from ram pipe
housing.
15.Fit approved hose clamp to water jacket coolant
hoses.
16.Tighten clamp.
17.Position cloth to absorb coolant spillage.
Do not carry out further dismantling if
component is removed for access only.
18.Slacken clips securing coolant hoses to plenum.

19FUEL SYSTEM
14
REPAIR
19.Disconnect hoses and remove plenum chamber.
20.Place cloth over ram pipes to prevent ingress of
foreign matter.
21.Remove 4 bolts securing water jacket to plenum
chamber. Remove water jacket. Remove gasket
and discard.
22.Remove 3 bolts securing throttle linkage bracket
to plenum chamber. Remove bracket. Collect
return spring.
23.Remove 2 Torx bolts securing TP sensor.
Collect clamp plate. Remove TP sensor.
24.Remove 2 bolts securing IAC. Remove motor.
Remove gasket and discard.

SFI
15
REPAIR REV: 09/95 Refit
25.Ensure all mating surfaces are clean.
26.Fit TP sensor. Ensure drive engages correctly
with throttle spindle.
27.Position clamp plate. Secure TP sensor with
bolts. Tighten to
2 Nm.
28.Using a new gasket, fit IAC. Secure with bolts.
Tighten to
2.3 Nm.
29.Ensure mating faces of water jacket and plenum
chamber are clean.
30.Using a new gasket, fit water jacket. Secure with
bolts. Tighten to
13 Nm.
31.Position throttle linkage bracket, fit and engage
return spring.
32.Secure linkage bracket to plenum chamber with
bolts. Tighten to
8 Nm.
33.Remove cloth from ram housing.
34.Ensure mating faces of plenum chamber and
ram pipe housing are clean.
35.Position plenum chamber. Connect coolant
hoses to water jacket. Secure with clips.
36.Remove clamp from coolant pipes. Remove
cloth.
37.Apply a thin, uniform coating of Loctite 577
sealant to sealing face of plenum chamber.
38.Fit plenum chamber.
39.Fit plenum chamber bolts. Tighten to
24 Nm.
40.Connect multiplugs to TP sensor and IAC.
41.Connect breather hose to plenum chamber.
42.Fit kick down cable to abutment bracket and fit
locknut.
43.Connect throttle cable to abutment bracket.
44.Connect vacuum hose to actuator.
45.Align throttle cable to lever. Fit clevis pin. Secure
clevis pin with split pin.
46.Align kick down cable to lever.
47.Fit clevis pin and secure clip.
48.Connect intake hose and secure with clip.
49.Reconnect battery negative lead.
50.Top up cooling system.RELAY MODULE - PRE ADVANCED EVAPS
Service repair no - 18.30.71
Remove
1.Release module from bracket.
2.Disconnect 2 multiplugs.
3.Remove module.
Refit
4.Reverse removal procedure.

SFI
17
REPAIR ADD: 09/95 Refit
6.Fit a NEW filter to bracket.
NOTE: Ensure direction of flow arrow
stamped on canister is correct.
7.Position filter mounting bracket to chassis and
secure with nut and bolt.
8.Remove plugs from fuel hose ends.
9.Lubricate NEW 'O' rings with clean fuel and fit to
fuel hoses.
10.Connect fuel hoses to filter and tighten unions to
18 Nm.
CAUTION: Use two spanners when
loosening or tightening unions.
11.Remove stand(s) and lower vehicle.
12.Run the engine to check for any fuel leaks.FUEL PUMP AND GAUGE SENDER UNIT -
ADVANCED EVAPS
Service repair no - 19.45.03
A plastic fuel tank with a combined fuel pump and
gauge sender unit is fitted. The top flange of the pump
also houses a pressure sensor which is not removable
from the pump. The fuel pump is accessed through a
panel in the load space floor.
WARNING: Ensure that fuel handling
precautions given in 01 - Introduction are
strictly adhered to when carrying out
following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Check the amount of fuel in the tank. If the tank
is full, drain 2.4 US gallons (9 litres) minimum.
See fuel tank - draining - advanced evaps
4.Remove 6 screws securing tail door tread strip
and remove tread strip.
5.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair, rear
compartment lower trim panels

19FUEL SYSTEM
18
REPAIRADD: 09/95
6.Fold back loadspace carpet and sound
insulation to reveal access panel.
7.Remove 6 screws securing fuel pump access
panel.
8.Remove access panel.
9.Disconnect multiplugs from fuel pump and
pressure sensor.
10.Release vent hose from pressure sensor body.
11.Noting their fitted positions, disconnect both fuel
connections by pressing the black release
latches on each connector and pushing the
connector back down the line. Care must be
taken to catch any excess fuel which may spill
from the fuel lines once removed.

SFI
19
REPAIR ADD: 09/95
12.Using service tool LRT-19-009 loosen and
remove the metal locking ring.
13.Prise the pump from the tank opening using a
blunt instrument under the edge of the pump
flange. Once clear of the seal, tip the pump to
the right to allow fuel contained in the body of
the pump to drain into the tank.
CAUTION: Do not lift the pump from the
tank using the feed and return stubs.
14.Remove and discard seal.Refit
15.Fit NEW pump seal to tank opening.
16.Carefully lower pump into tank opening, pressing
firmly on the pump top flange to allow correct
positioning.
NOTE: Ensure location tag on pump top
flange is engaged correctly to tank
opening lip.
17.Fit locking ring and tighten to
35 Nmusing
service tool LRT-19-009.
18.Connect both fuel lines to the pump by pushing
the connectors down each line square to the
pump connection until the connectors positively
latch.
19.Connect vent hose to pressure sensor body.
20.Connect multiplugs to fuel pump and pressure
sensor.
21.Reconnect battery negative lead.
22.Refill tank with drained fuel.
23.Run the engine to check for any fuel leaks.
24.Fit access panel and secure with screws.
25.Reposition loadspace sound insulation and
carpet.
26.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair, rear
compartment lower trim panels
27.Fit tail door tread strip and secure with screws.

SFI
21
REPAIR ADD: 09/95
5.Fold back loadspace carpet and sound
insulation to reveal access panel.
6.Remove 6 screws securing fuel pump access
panel.
7.Remove access panel.8.Disconnect multiplugs from fuel pump and
pressure sensor
9.Noting their fitted positions, disconnect both fuel
connections by pressing the black release
latches on each connector and pushing the
connector back down the line.
10.Care must be taken to catch any excess fuel
which may spill from the fuel lines once
removed.
11.Raise rear of vehicle.
WARNING: Support on safety stands.

19FUEL SYSTEM
22
REPAIRADD: 09/95
12.Mark location of anti-roll [sway] bar straps.
13.Remove nuts and bolts securing anti-roll [sway]
bar straps, and allow bar to swing down clear of
tank.14.Disconnect pressure sensor breather pipe
connection.
15.Disconnect vent line quickfit connector from
liquid/vapour separator.
16.Remove torque screw cap from hose to tank
filler neck clip.
17.Loosen clip screw securing hose to tank filler
neck.
18.Release hose from filler neck and internal filler
neck breather hose from fuel tank.
19.Remove and discard fuel filler neck clip.

SFI
23
REPAIR ADD: 09/95
20.Remove nut and bolt securing RH side of upper
fuel tank strap to chassis.
21.Remove 4 nuts and bolts securing fuel tank
cradle.
22.Remove fuel tank cradle.
23.With assistance, tilt right hand side of tank
upwards and manoeuvre through chassis to
remove.
Do not carry out further dismantling if
component is removed for access only.
24.Release vent hose from tank pressure sensor.
25.Remove vent hose from 3 fuel tank clips.
26.Using service tool LRT-19-009 loosen and
remove the metal locking ring.
27.Prise the pump from the tank opening using a
blunt instrument under the edge of the lip of the
pump flange.
CAUTION: Do not lift the pump from the
tank using the feed and return stubs.
28.Remove and discard seal.

19FUEL SYSTEM
24
REPAIRADD: 09/95 Refit
29.Fit NEW pump seal to tank opening.
30.Carefully lower pump into tank opening, pressing
firmly on the pump top flange to allow correct
positioning.
NOTE: Ensure location tag on pump top
flange is engaged correctly to tank
opening lip.
31.Fit locking ring and tighten to
35 Nmusing
service tool LRT-19-009.
32.Fit vent hose to fuel tank clips and connect to
pressure sensor.
33.With assistance, fit fuel tank into position.
34.Fit fuel tank cradle and secure with nuts and
bolts.
35.Align upper fuel tank strap and secure with nut
and bolt.
36.Fit NEW clip to fuel filler neck hose.
37.Connect fuel filler neck internal breather to tank.
38.Connect fuel filler neck hose to tank.
39.Position fuel filler neck hose clip and tighten until
head shears.
40.Connect vent line quickfit connector to
liquid/vapour separator.
41.Connect vent line hose connection.
42.Position anti-roll [sway] bar straps and secure
with nuts and bolts.
43.Remove stand(s) and lower vehicle.
44.Connect both fuel lines to the pump by pushing
the connectors down each line square to the
pump connection until the connectors positively
latches.
45.Connect multiplugs to fuel pump and pressure
sensor.
46.Reconnect battery negative lead.
47.Refill tank with drained fuel.
48.Run the engine to check for any fuel leaks.
49.Fit access panel and secure with screws.
50.Reposition loadspace sound insulation and
carpet.
51.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair, rear
compartment trim panels
52.Fit tail door tread strip and secure with screws.FUEL TANK - DRAINING - ADVANCED EVAPS
Service repair no - 19.55.02
WARNING: Before removing the fuel tank
it must be drained.
WARNING: Petrol/gasoline vapour is
highly flammable and in confined spaces
is also explosive and toxic. Always have a
fire extinguisher containing FOAM, CO2, GAS or
POWDER close at hand when handling or draining
fuel. See Introduction
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
NOTE: Assuming the fuel tank is FULL
drain the following quantities:
Renew Fuel pump = 9 Litres (2.4 US Gallons)
Renew Fuel filler neck = 22 Litres (6 US Gallons)
Renew Fuel tank = COMPLETE DRAIN
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Remove 6 screws securing tail door tread strip
and remove tread strip.
4.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair,