LAND ROVER DISCOVERY 1995 Workshop Manual

FRONT AXLE AND FINAL DRIVE
9
OVERHAUL 19.Lubricate seal and lip with EP90 oil and with
cavity side leading press in a new oil seal using
special tool LRT-54-004.
20.Using special tool LRT-54-005, fit bearing with
its part number visible when fitted, and flush with
end face of stub axle.
21.Press fit a new thrust ring onto stub axle.
Swivel pin housing assembly
22.Remove brake disc shield bracket.
23.Disconnect track-rod end ball joint from housing.
24.Disconnect drag-link ball joint.
25.Disconnect jump hoses from brake jump hose
bracket.
26.Remove ABS brake sensor.
27.Remove six bolts securing oil seal and retaining
plate to swivel pin housing. Prise seal from
swivel pin housing.
NOTE: Oil seal and retaining plate cannot
be removed until swivel pin bearing
housing is removed.
28.Remove two screws securing brake
damper/shield bracket and lower swivel pin to
housing.
29.Withdraw lower swivel pin and joint washer by
tapping protruding lug.
30.Remove top swivel pin retaining bolts complete
with brake jump hose bracket.
31.Remove top swivel pin and shims.
32.Remove swivel pin housing while retrieving
lower taper bearing.
Swivel pin bearing housing
33.Remove seven bolts securing swivel pin bearing
housing to axle case.
34.Remove and discard oil seal and joint washer.
35.Remove lower swivel pin bearing track.
36.Remove top swivel pin bush housing assembly.
Discard two thrust washers and bearing.
37.If worn, pitted or damaged, renew swivel pin
bearing housing.
38.Fit a new lower swivel pin bearing track.
39.Fit a new bush and bush housing. Ensure
relieved lip of bush housing faces towards rear,
as shown.

54FRONT AXLE AND FINAL DRIVE
10
OVERHAUL
40.With seal lips trailing press axle shaft oil seal
flush into rear of housing. Grease lips.
41.Fit new thrust washers and bearing into top
swivel pin bush.
42.Hang swivel pin bearing housing oil seal and
retainer plate over back of housing. Ensure they
are in correct assembly order.
43.Fit a new joint washer and secure swivel pin
bearing housing to axle. Starting with top fixing
dowel bolt. Tighten to
72Nm.
Fit swivel pin housing
44.Grease and fit lower swivel pin bearing to
bearing housing.
45.Place swivel pin housing in position over swivel
pin bearing housing.
46.Using a new joint washer, fit lower swivel pin
with lip outboard. Do not secure with screws at
this stage.
47.Fit a new sensor bush and new oil seal, lip side
leading to top swivel pin.
48.Lubricate with a recommended oil and fit top
swivel pin with existing shims.
49.Coat threads of top swivel pin bolts with Loctite
542. Fit bolts and jump hose bracket (do not
tighten).50.Coat threads of lower swivel pin screws with
Loctite 270 and fit, together with damper and
shield bracket. Tighten to
25 Nm.
51.Tighten top swivel pin and brake jump hose
bracket securing bolts to
65 Nm.
Check and adjust preload on bearings
52.The preload on bearings to be0,25 to 0,30 mm,
withoutswivel housing oil seal and axle fitted,
and reading from centre of swivel pin. The
torque required to turn swivel assembly from
lock to lock to be
2.0 to 2.8 Nm.Adjust by
removing or adding shims as necessary.
53.To take a reading use special tool LRT-57-024
torque test adaptor, with a torque wrench and
extension as shown.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to
11Nm.
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.

FRONT AXLE AND FINAL DRIVE
11
OVERHAUL Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 o'clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle. Before stub axle
is secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with six bolts and
tighten evenly to
65 Nm.
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit front hub complete assembly.
See Repair,
Front Hub Assembly
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil.
See SECTION 10, Maintenance, Under
Vehicle Maintenance
67.Set steering lock stop bolts to provide a
clearance of 20mm.
See STEERING,
Adjustment, Steering Lock Stops
68.Fit ABS brake sensor.See BRAKES, Repair,
Sensors - Front

54FRONT AXLE AND FINAL DRIVE
12
OVERHAUL FRONT HUB AND SWIVEL COMPONENTS
1. Brake caliper.
2. Mud shield.
3. Stub axle.
4. Joint washer.
5. Oil seal.
6. Bearing.
7. Brake disc shield.
8. Constant velocity joint.
9. Circlip.
10. Bush.
11. Inner driveshaft.
12. Top swivel pin and jump hose bracket.
13. Shim.
14. Swivel pin housing.15. Joint washer.
16. Lower swivel pin.
17. Damper and shield bracket.
18. Thrust washer, ABS.
19. Bush and housing, ABS.
20. Swivel pin bearing housing.
21. Lower swivel pin bearing (and upper bearing non
ABS).
22. Oil seal.
23. Oil seal retaining plate.
24. Joint washer.
25. Oil seal, ABS.
26. Sensor bush, ABS.
27. Thrust bearing, ABS.

FRONT AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
FRONT AXLE
Hub driving member to hub 65........................................................................ *
Brake disc to hub 73.......................................................................................
Stub axle to swivel pin housing 65.................................................................. *
Brake caliper to swivel pin housing 82............................................................
Upper swivel pin to swivel pin housing 78...................................................... *
Upper swivel pin to swivel pin housing ABS 65..............................................
Lower swivel pin to swivel pin housing 78...................................................... *
Lower swivel pin to swivel pin housing ABS 25.............................................. *
Oil seal retainer to swivel pin housing 11........................................................
Swivel bearing housing to axle case 73.......................................................... *
Pinion housing to axle case 41.......................................................................
Crown wheel to differential housing 58...........................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Mudshield to bracket lower swivel pin 11........................................................
Disc shield to bracket lower ABS 9................................................................
Bevel pinion nut 130........................................................................................
Draglink to hub arm 40....................................................................................
Panhard rod to axle bracket 88.......................................................................
Radius arm to axle 190....................................................................................
Radius arm to chassis side member 190.........................................................
NOTE: * These bolts to be coated with Loctite 270 prior to assembly.

54FRONT AXLE AND FINAL DRIVE
2
SPECIFICATIONS, TORQUE Torque values below cover all screws and bolts used, unless specified otherwise.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
FRONT HUB AND SWIVEL DATA
Front hub
Front hub end float 0,010 mm..................................................
Drive shaft end play 0,08 to 0,25 mm................................................
Swivel pin bearing preload
ABS vehicles - Torque to turn 2. to 3. Nm.................................
Non ABS vehicles - Resistance to turn 1,16 to 1,46Kg...................

FRONT AXLE AND FINAL DRIVE
1
SERVICE TOOLS FRONT HUB
LRT-54-001 Oil seal replacer non ABS
LST550-5
LRT-99-003 Drift
18G134
LRT-54-002 Hub nut wrench
RO606435A
LRT-54-003 Hub oil seal replacer ABS
LST137

54FRONT AXLE AND FINAL DRIVE
2
SERVICE TOOLS
LRT-99-503 Dial gauge bracket
RO530106
LRT-37-004 Extractor ABS
18G284AAH
LRT-54-005 Bearing installer ABS
LST132
LRT-54-004 Seal installer ABS
LST133

FRONT AXLE AND FINAL DRIVE
3
SERVICE TOOLS
LRT-99-004 Impulse extractor
MS284
LRT-570-024 Torque test adaptor ABS
LST141

STEERING
1
DESCRIPTION AND OPERATION DESCRIPTION
The power assisted steering system incorporates a
compression joint in the lower shaft, designed to
collapse on impact and for certain countries, an air
bag located in the centre of the steering wheel.
The mis-alignment of the upper steering column with
the steering box and the inclusion of two universal
joints and a compression joint in the lower shaft, is
also designed to prevent frontal impact moving the
column toward the driver.
The steering box is located behind the first cross
member of the chassis and is connected to the road
wheels by the drag link and track rod. An hydraulic
damper absorbs shocks in the steering, caused by
road wheel deflections when operating on rough
terrain.Power steering system
The power steering system comprises a hydraulic
pump which is belt driven from the engine and
supplied with fluid from a reservoir that also acts as a
cooler.
The steering box houses a self neutralizing rotary
valve which is part of the worm/valve assy and a
hydraulic piston/rack to assist the mechanical
operation.
The rotary valve which is operated by movement of
the steering wheel, directs fluid pressure to the
appropriate side of the hydraulic piston/rack to provide
assistance.
Power steering system
1. Hydraulic pump
2. Fluid reservoir
3. Steering box
4. Upper column
5. Universal joints
6. Lower shaft
7. Compression joint
8. Drag link