ECU LAND ROVER DISCOVERY 1995 Manual Online

19FUEL SYSTEM
6
REPAIR FUEL FILTER ELEMENT
Service repair no - 19.25.07
Remove
1.Disconnect battery negative lead.
2.Clean area around filter head.
3.Place a suitable container beneath filter bowl to
collect any spillage.
4.Loosen bleed screw.
5.Loosen drain tap, allow fuel to drain into
container.
6.Unscrew filter element, discard element.
Refit
7.Clean seal and seating in filter head.
8.Lubricate filter element seal with fuel.
9.Position filter element to filter head and hand
tighten.
10.Reconnect battery negative lead.
11.Crank engine until fuel is drawn through the
system and starts.INTERCOOLER
Service repair no - 19.42.15
Remove
1.Disconnect battery negative lead.
2.Release 2 clips securing fan cowl to radiator top
cover.
3.Remove 4 bolts securing radiator top cover,
remove top cover.
4.Remove nut, bolt and washers securing
intercooler side cover bracket to bonnet [hood]
platform.
5.Release bracket from side cover lug, position
bracket and power steering reservoir aside.
6.Position side cover away from intercooler.
7.Loosen 2 clips and disconnect top hose from
intercooler.
8.Loosen 2 clips and disconnect bottom hose from
intercooler.

Tdi
7
REPAIR
9.Move intercooler upwards and clear of fan cowl.
Refit
10.Ensure locatiing lug grommets are fitted and in
good condition.
11.Ensure foam pad is in good condition and
attached to intercooler.
12.Move intercooler into position.
13.Reverse removal procedure.GLOW PLUGS
Service repair no - 19.60.31
Remove
1.Disconnect battery negative lead.
No.1 glow plug - air conditioning models
2.Release drive belt from compressor pulley.See
ENGINE, Repair, Drive Belt Renew
3.Remove 4 bolts securing compressor to front
cover, move compressor aside.
No.3 glow plug
4.Remove bolt securing Hummel valve, withdraw
valve, remove and discard 'O' ring.

19FUEL SYSTEM
8
REPAIR
All glow plugs
5.Remove terminal nut from glow plug, disconnect
wire from glow plug terminal.
6.Remove glow plug.
Refit
7.Clean glow plug and seating.
8.Coat threads of glow plug with suitable anti-seize
compound operational to a temperature of
1000°C.
9.Fit glow plug. Tighten to
23 Nm.
10.Connect wire to glow plug terminal and secure
with nut.
NOTE: Feed wire must be connected to
No. 4 glow plug terminal.
11.
No. 3 glow plug:Lubricate new 'O' ring with
engine oil and fit to Hummel valve. Fit valve and
secure with bolt. Tighten to
15 Nm.
No. 1 glow plug - air conditioning models
12.Position compressor to front cover, fit bolts.
Tighten to
25 Nm.
13.Fit drive belt to compressor pulley and adjust
tension.
See ENGINE, Repair, Drive Belt
Renew
All models
14.Reconnect battery negative lead.EGR VALVE
Service repair no - 19.45.01
Remove
1.Disconnect multiplug from EGR valve.
2.Disconnect vacuum pipe from EGR valve.
3.Remove 2 Allen screws securing EGR valve to
exhaust manifold.
4.Remove 2 bolts securing hose to EGR valve.
5.Remove EGR valve and discard gaskets.
Refit
6.Clean mating faces of EGR valve and exhaust
manifold.
7.Reverse removal procedure. Tighten bolts to
25
Nm.

Tdi
9
REPAIR GLOW PLUG CONTROL UNIT
Service repair no - 19.60.33
Remove
1.Disconnect battery negative lead.
2.Remove nut and bolt securing control unit to
mounting bracket.
3.Disconnect multiplug and remove control unit.
Refit
4.Reverse removal procedure.EGR CONTROL UNIT
Service repair no - 19.45.06
Remove
1.Release 2 glovebox stays from fascia and pivot
glovebox fully downwards.
2.Remove 2 plastic nuts securing control unit to
body.
3.Release control unit from fixings.
4.Disconnect multiplug and remove control unit.
Refit
5.Reverse removal procedure.

19FUEL SYSTEM
10
REPAIR EGR THROTTLE POSITION SENSOR
Service repair no - 19.30.14
Remove
1.Remove 2 screws securing sensor mounting
plate to injection pump.
2.Disconnect sensor multiplug from harness.
3.Remove sensor assembly.
Refit
4.Position sensor assembly on injection pump and
fit and tighten screws.
5.Connect multiplug.
6.Adjust sensor.
See Adjustment, EGR Throttle
Position Sensor
INJECTORS
Service repair no - 19.60.10
Remove
1.Remove oil filler cap and remove sound
deadening pad from top of engine.
2.Remove high pressure pipe from relevant
injector and injection pump.
3.Disconnect spill return hose(s) from injector.
4.Plug pipes and injector connections to prevent
the ingress of dirt and foreign matter.
5.Remove nut securing injector clamp plate to
cylinder head.
6.Remove injector.
Refit
7.Reverse removal procedure. Renew copper
washer on injector. Tighten injector clamp plate
nut to
25 Nm.

19FUEL SYSTEM
12
REPAIR 12.Remove pin from pump gear.
13.Fit gear retaining tool LRT-12-045 with an 8 mm
washer, 1.5 to 2 mm thick, under each bolt head
in addition to the existing washer.
14.Remove throttle cable and hand throttle cable if
fitted.15.Disconnect stop control solenoid connector.
16.Remove banjo bolts securing spill return, main
fuel and boost signal pipes, refit banjo bolts after
disconnecting pipes.
17.Remove pump mounting bracket bolts 2 off.
18.Loosen pump support bracket bolts to block,
sufficient for bracket to just move.
19.Remove pump securing nuts at flange and
withdraw pump and gasket.
20.Fit blanks to pipe connections.

Tdi
13
REPAIR Refit
21.Remove blanks from pump.
22.Remove special tool pin from pump.
23.Clean mating faces of pump and front cover.
24.Fit pump to cover with a new gasket and secure
with nuts. Tighten to
25 Nm.
25.Attach pump to bracket and finger tighten nuts
and bolts
26.First tighten bolts securing bracket to block and
then bolts securing pump to bracket.
27.Connect spill return, main fuel pipes. Tighten to
25 Nm.
28.Connect boost signal pipe and secure with banjo
bolts. Tighten to
10 Nm.
29.Connect stop control solenoid lead.
30.Connect throttle cable and where applicable
hand throttle cable.
31.Remove special tool LRT-12-045.
32.Fit gear lock plate.
33.Fit pin from special tool LRT-12-045.
34.Secure gear with bolts.
35.Remove special tool pin.
36.Turn crankshaft two complete revolutions, check
timing pin from LRT-12-045 can be fully and
easily inserted into the pump. At the same time
check flywheel timing pin LST-12-044 can also
be inserted in the flywheel slot.
37.If, with the flywheel timing pin located, the timing
pin cannot be inserted cleanly into the injection
pump, carry out the following:
(a) Ensure flywheel timing pin is disengaged
from slot in flywheel.
(b) Turn the crankshaft the small amount
necessary to enable the timing pin to be
inserted into the pump.
(c) Loosen the three pump gear retaining
bolts.
(d) Turn the crankshaft to T.D.C..
(e) Check that the timing pin is an easy fit in
the pump and that the flywheel timing pin
locates.
(f) Tighten the pump gear retaining bolts to
the correct torque.
(g) Remove the timing pin from the pump and
the timing tool from the flywheel housing.
38.Using antisieze compound, fit the blanking plug
to flywheel housing. Tighten to
12 Nm.
39.Fit access plate with gasket to front cover plate.
Tighten to
25 Nm.
40.Refit injector pipes. Tighten to29 Nm.

19FUEL SYSTEM
14
REPAIR ENGINE CONTROL MODULE (ECM)
Service repair no - 18.30.03
NOTE: The ECM is not a serviceable item,
in the event of failure it must be renewed.
Remove
1.Disconnect battery negative lead.
2.Remove 'A' post trim pad.
3.Loosen multi-plug screw to ECM.
4.Disconnect multi-plug from ECM.
5.Secure multi-plug and harness aside.
6.Remove retaining nuts from ECM.
7.Manoeuvre ECM from its mounted position.
Refit
8.Refitting is the reverse of removal procedure.
9.Reconnect harness plug. Ensure plug is pushed
firmly into location and retaining clip secures
plug in position.
10.Tighten screw securing multi-plug.AIRFLOW METER
Service repair no - 18.30.15
NOTE: The air flow meter is not a
serviceable item, in the event of failure it
must be renewed.
Remove
1.Disconnect battery negative lead.
2.Release vacuum tube from EGR vacuum
capsule.
3.Disconnect airflow meter multi-plug.
4.Loosen air cleaner hose to air flow meter
retaining clip.
5.Disconnect hose from airflow meter.
6.Loosen turbo charger hose to airflow meter
retaining clip.
7.Disconnect hose from airflow meter.
8.Remove meter to mounting bracket bolts.
9.Remove airflow meter.
Refit
10.Reverse removal procedure. Ensure multi-plug is
firmly reconnected and hose clamps are
securely tightened to prevent unmetered air
entering the engine.

19FUEL SYSTEM
18
REPAIR BRAKE PEDAL SWITCH
Service repair no - 18.30.66
Remove
1.Disconnect battery negative lead.
2.Disconnect switch wiring Lucars.
3.Loosen rear locknut.
4.Remove front locknut.
5.Remove switch from mounting bracket.
Refit
6.Reverse removal procedure.COOLANT TEMPERATURE SENSOR
Service repair no - 18.30.68
Remove
1.Disconnect battery negative lead.2.Disconnect sensor multi-plug.
3.Remove sensor.
4.Clean off water spillage from sensor area.
Refit
5.Fit a new copper washer.
6.Fit sensor and tighten securely.
7.Refill cooling system.
8.Run engine, check for water leaks around
sensor.

Tdi
19
REPAIR THROTTLE POSITION SENSOR
Service repair no - 18.30.17
NOTE: The throttle position sensor is not a
serviceable item, in the event of failure it
must be renewed.
Remove
1.Disconnect battery negative lead.
2.Disconnect multiplug from sensor.
3.Remove nut securing throttle pedal quadrant to
sensor. Remove throttle pedal quadrant.
4.Remove two screws securing sensor to pedal
box.
5.Remove sensor.
Refit
6.Reverse removal procedure.
CAUTION: DO NOT operate throttle
mechanism while sensor is loosely fitted,
damage may be caused to sensor wiper
track.ELECTRO-PNEUMATIC MODULATOR
Service repair no - 18.30.69
Remove
1.Disconnect battery negative lead.
2.Disconnect multi-plug from modulator.
3.Remove three vacuum pipes from modulator.
4.Remove nut securing modulator to inner wing.
5.Remove modulator.
Refit
6.Reverse removal procedure.