belt LAND ROVER FREELANDER 2001 Workshop Manual

RESTRAINT SYSTEMS
75-6 REPAIRS
Stalk - rear seat belt - LH - 3 door
$% 76.73.32
Remove
1.Remove rear seat.

+ SEATS, REPAIRS, Cushion & squab
- rear seat - bench type - 3 door.
2.Remove 2 screws from hinge cover and
remove cover from seat hinge.
3.Remove 4 screws and remove rear seat centre
console.
4.Release rear seat cushion cover retainers and
position cushion aside.5.Remove Torx bolt from seat belt buckle and
remove buckle.
Refit
1.Fit buckle to seat frame and tighten Torx bolt to
32 Nm (24 lbf.ft).
2.Position seat cushion and secure cover
retainers.
3.Fit centre console and secure with screws.
4.Fit hinge cover and secure with screws.
5.Fit rear seat.

+ SEATS, REPAIRS, Cushion & squab
- rear seat - bench type - 3 door.

RESTRAINT SYSTEMS
REPAIRS 75-7
Stalk - rear seat belt - LH - 5 door
$% 76.73.32
Remove
1.Fold rear seat forward.
2.Remove 3 screws from end cover and remove
cover from seat hinge.
3.Remove 4 Torx bolts from seat lock down catch
and remove catch assembly.
4.Remove Torx bolt from seat belt buckle and
remove buckle.Refit
1.Fit buckle to catch assembly and tighten Torx
bolt to 32 Nm (24 lbf.ft).
2.Fit catch assembly to seat and tighten Torx
bolts.
3.Fit catch assembly to seat, fit Torx bolts but do
not tighten at this stage.
4.Fold seat down and check that seat unfolds on
lock down bar correctly. Adjust catch assembly
if required.
5.Tighten catch Torx bolts to 32 Nm (24 lbf.ft).
6.Recheck seat fold.
7.Fit end cover and tighten screws.
8.Reposition rear seats.

RESTRAINT SYSTEMS
75-8 REPAIRS
Pre-tensioner - seat belt - front
$% 76.73.75
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
WARNING: When removing, testing or
installing a seatbelt pre-tensioner, do not
lean directly over it or block the end of the
piston tube.
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.
3.Disconnect pretensioner multiplug.
4.Remove Torx bolt securing pretensioner to seat
and remove pretensioner.
WARNING: Store the airbag module or seat
belt pre-tensioner in a designated storage
area. If there is no designated storage area
available, store in the locked luggage
compartment/loadspace of the vehicle and
inform the workshop supervisor.Refit
NOTE: If the SRS component is to be replaced,
the bar code of the new unit must be recorded.
1.Position pretensioner to seat and tighten Torx
bolt to 32 Nm (24 lbf.ft).
2.Connect pretensioner multiplug and secure to
seat frame.
3.Fit rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.
4.Connect battery leads, earth lead last.

RESTRAINT SYSTEMS
REPAIRS 75-9
Pre-tensioner - seat belt - front -
deployment - off vehicle
$% 76.73.78
These guidelines are written to aid authorised
personnel to carry out the safe disposal of airbag
modules when removed from the vehicle.
Deploy
It is imperative that before any work is
undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Make the SRS system safe.

+ GENERAL INFORMATION, SRS
component manual deployment.
2.Remove seat belt pre-tensioner from vehicle.

+ RESTRAINT SYSTEMS, REPAIRS,
Pre-tensioner - seat belt - front.
3.Check condition of deployment tool LRT-86-
003 and associated fly leads.
4.Position LRT-86-007/02 in vice, ensuring that
vice jaws grip tool above the bottom flange to
prevent possibility of tool being forced upwards
during detonation. Tighten vice.

RESTRAINT SYSTEMS
75-10 REPAIRS
5.Fit and secure seat belt pre-tensioner to LRT-
86-007/02.
6.Connect deployment tool fly lead LRT-86-003/
04 to seat belt pre-tensioner.
7.Connect deployment tool LRT-86-003 to
deployment tool fly lead LRT-86-003/04.
8.Connect deployment tool LRT-86-003 to
battery.
9.Press deployment tool operating button to
deploy seat belt pre-tensioner.
WARNING: Ensure all personnel are at least
15 metres (50 feet) away from the airbag
module.
10.Disconnect deployment tool from battery.
WARNING: During deployment parts of the
airbag module become hot enough to burn
you. Wait 30 minutes after deployment
before touching the airbag module.
11.Disconnect deployment tool fly lead from seat
belt pre-tensioner.
12.Remove seat belt pre-tensioner from holding
tool and place in a sealed bag, ready for
disposal.
13.Wipe down holding tools with a damp cloth and
remove from vice.14.Transport deployed seat belt pre-tensioner to
designated area for incineration.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.
15. Do not re-use or salvage any parts of the
SRS system.

RESTRAINT SYSTEMS
REPAIRS 75-11
Stalk - rear seat belt - centre
$% 76.73.98
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
WARNING: When removing, testing or
installing a seatbelt pre-tensioner, do not
lean directly over it or block the end of the
piston tube.
WARNING: Always remove the key from the
starter switch, disconnect the vehicle
battery and wait 10 minutes before
commencing work on the SRS system.
1.Remove RH rear seat.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove 2 screws and remove seat belt reel
cover.3.Remove nut and release seat belt reel.
4.Remove 5 screws and remove both end
covers.
5.Remove 3 Torx bolts and remove squab from
cushion.

RESTRAINT SYSTEMS
75-12 REPAIRS
6.Release rear of cushion cover from frame.
7.Release sides and front of cushion cover from
frame.
8.Release cover and pad from frame.
9.Remove Torx bolt from seat belt buckle and
remove buckle.Refit
1.Position seat belt and buckle to frame and
tighten to 32 Nm (24 lbf.ft).
2.Fit cover and pad to frame.
3.Fit front and sides of cushion cover to frame.
4.Fit rear of cushion cover to frame.
5.Fit cushion to squab and tighten Torx bolts.
6.Fit end covers and tighten screws.
7.Position seat belt reel in seat squab and tighten
nut to 32 Nm (24 lbf.ft).
8.Fit seat belt reel cover and tighten screws.
9.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.

RESTRAINT SYSTEMS
REPAIRS 75-23
Pre-tensioner - front seatbelt -
deployment - in-vehicle
$% 76.73.77
These guidelines are written to aid authorised
personnel to carry out the safe deployment and
disposal of seatbelt pre-tensioners when they are still
fitted in the vehicle.
Deploy
WARNING: It is imperative that before any
work is undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Make the SRS system safe.

+ GENERAL INFORMATION, SRS
component manual deployment.
2.Check condition of deployment toolLRT-86–
003 and associated flyleads.
3.Slide seat fully rearwards to access pre-
tensioner harness connector.
4.Disconnect pre-tensioner harness connector.
WARNING: Ensure the deployment tool is
not connected to the battery.
5.Connect deployment tool flylead LRT-86–003–
04 to pre-tensioner connector.
6.Connect deployment tool flylead LRT-86–003–
04 to deployment tool LRT-86–003.
WARNING: Ensure the SRS component to
be deployed is securely fastened to its
mounting.
WARNING: Ensure all personnel are at least
15 metres (50 ft) away from the vehicle.
7.Connect deployment tool LRT-86–003 to
battery.

RESTRAINT SYSTEMS
75-24 REPAIRS
8.Press deployment tool operating button to
deploy airbag module.
WARNING: A deployed airbag or seatbelt
pre-tensioner is very hot, DO NOT return to
a deployed airbag module until at least 30
minutes have elapsed since deployment.
9.Disconnect flylead LRT-86–003–04 from pre-
tensioner connector and remove pre-tensioner
from seat.

+ RESTRAINT SYSTEMS, REPAIRS,
Pre-tensioner - seat belt - front.
10.Place pre-tensioner in plastic bag and seal bag.
11.Transport deployed pre-tensioner to
designated area for incineration.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.
12.Scrap all remaining parts of the seat belt and
SRS system. DO NOT re-use or salvage any
parts of the seat belt and SRS system.

INTERIOR TRIM COMPONENTS
76-3-2 REPAIRS
Trim casing - rear quarter - lower - 5 door
$% 76.13.12
Remove
1.Release rear seat squab and fold seat forward.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release load space lamp from trim casing.
4.Disconnect 2 Lucars and remove load space
lamp.
5.Remove 2 screws securing casing to load
space carpet retainer.
6.Release 4 turn buckles securing trim casing.
7.Release trim casing from 5 retaining clips.
8.Remove loadspace side trim casing.
9.Remove 5 retaining clips from trim casing.Refit
1.Fit retaining clips to casing.
2.Position casing in loadspace, locate and secure
retaining clips.
3.Fit turn buckles.
4.Fit screws securing casing to carpet retainer.
5.Position load space lamp to casing, connect
Lucars and secure lamp to casing.
6.Position loadspace cover retainer and secure
with screw.
7.Fit loadspace cover and secure in retainers.
8.Position rear seat belt and tighten bolt to 40 Nm
(29 lbf.ft).
9.Reposition rear seats.