fuel LAND ROVER FREELANDER 2001 Owner's Guide

TORQUE WRENCH SETTINGS
06-13
Fuel delivery system – Petrol
1 Tighten in sequence using the procedure defined in 'Repairs' section.

+ ENGINE MANAGEMENT SYSTEM - SIEMENS, REPAIRS, Sensor - combined - manifold absolute
pressure/Intake air temperature (MAP/IAT).
TORQUE DESCRIPTION METRIC IMPERIAL
Air cleaner to battery tray bolts 9 Nm 7 lbf.ft
Fuel filler neck to body nuts and bolt 9 Nm 7 lbf.ft
Fuel pump/sender unit to tank locking ring 35 Nm 26 lbf.ft
Fuel rail to inlet manifold bolt 8 Nm 6 lbf.ft
Fuel tank to body bolts 40 Nm 29 lbf.ft
Heated Oxygen (HO
2S) Sensor 40 Nm 29 lbf.ft
Ignition coils to LH inlet manifold nuts and bolts - KV6 - Up to 03 Model Year 9 Nm 7 lbf.ft
Inertia (fuel cut-off) switch 2 Nm 1.5 lbf.ft
Intake Air Control Valve (IACV) to throttle body Allen screws 6 Nm 4.5 lbf.ft
Subframe to body bolts 190 Nm 140 lbf.ft
Throttle housing to inlet manifold bolts
1 (K1.8)
⇒1st. stage4 Nm 3 lbf.ft
⇒2nd. stage9 Nm 7 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 8 Nm 6 lbf.ft
Throttle actuator support bracket to throttle body Torx screws (vehicles with cruise
control only)9 Nm 7 lbf.ft
Throttle position sensor to housing Torx screws 1.5 Nm 1.1 lbf.ft
VIS motor to inlet manifold chamber screws (KV6 only) 8 Nm 6 lbf.ft

TORQUE WRENCH SETTINGS
06-14
Cooling System – Td4
Cooling System – K1.8
Cooling System – KV6
†Tighten in sequence.
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant hose adaptor to cylinder head bolts 8 Nm 6 lbf.ft
Coolant rail (lower) to sump bolts 10 Nm 7.5 lbf.ft
Coolant rail to cylinder head bolt 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolt 20 Nm 15 lbf.ft
Coolant pump to cylinder block bolts 10 Nm 7.5 lbf.ft
Fan and motor assembly to fan cowl bolts 5 Nm 4 lbf.ft
Fan cowl to radiator bolts 5 Nm 4 lbf.ft
Fuel cooler to mounting nuts 10 Nm 7.5 lbf.ft
Fuel rail to coolant rail bolt 10 Nm 7.5 lbf.ft
Heatshield to coolant rail Allen screws 8 Nm 6 lbf.ft
Thermostat housing to coolant pump bolts 8 Nm 6 lbf.ft
Upper coolant rail to thermostat housing bolt 8 Nm 6 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Condenser to radiator bolts 3 Nm 2.2 lbf.ft
Cooling fan control unit mounting bolt 5 Nm 4 lbf.ft
Cooling fan cowl to radiator 5 Nm 4 lbf.ft
Cooling fan and motor assembly to cowl bolts 5 Nm 4 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant pump to cylinder block bolts
†9 Nm 6.5 lbf.ft
Cooling fan and motor assembly to fan cowl bolts 5 Nm 3.7 lbf.ft
Cooling fan cowl to radiator bolts 5 Nm 3.7 lbf.ft
Cylinder block drain plug
+20 Nm 15 lbf.ft
Injector protection cover to RH fuel rail and inlet manifold bolts 9 Nm 6.5 lbf.ft
Radiator baffle bolts 5 Nm 3.7 lbf.ft
Thermostat housing flange / coolant elbow bolt 18 Nm 13 lbf.ft

TORQUE WRENCH SETTINGS
06-15
Manifolds and Exhaust System – Td4
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant rail to cylinder head bolt 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolt 20 Nm 15 lbf.ft
Coolant rail to thermostat housing bolt 8 Nm 6 lbf.ft
EGR cooler to cylinder head and lifting bracket bolts 25 Nm 18 lbf.ft
EGR pipe clamp screw 10 Nm 7.5 lbf.ft
EGR pipe to cylinder head bolt 20 Nm 15 lbf.ft
EGR pipe to manifold Torx screws 22 Nm 16 lbf.ft
Exhaust manifold to cylinder head nuts 24 Nm 18 lbf.ft
Front pipe clamping plate nuts 50 Nm 37 lbf.ft
Front pipe to intermediate pipe flange nuts 60 Nm 44 lbf.ft
Fuel rail to coolant rail bolt 10 Nm 7.5 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Heat shield to coolant rail Allen screws 8 Nm 6 lbf.ft
Inlet manifold:
⇒ M6 bolts10 Nm 7.5 lbf.ft
⇒ M7 bolts and nuts 15 Nm 11 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft
Turbocharger to exhaust manifold bolts 50 Nm 37 lbf.ft
Turbocharger outlet pipe bolts:
⇒6 mm10 Nm 7.5 lbf.ft
⇒8 mm25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-28
Brakes
1 Use NEW bolts
TORQUE DESCRIPTION METRIC IMPERIAL
ABS ECU pipe unions 17 Nm 12 lbf.ft
ABS modulator to mounting bracket bolts 9 Nm 7 lbf.ft
ABS modulator mounting bracket to inner wing:
⇒ Nuts
⇒ Bolts13 Nm
8 Nm10 lbf.ft
6 lbf.ft
Bleed screw - front calipers 10 Nm 7.5 lbf.ft
Brake servo to bulkhead nuts 22 Nm 16 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR pipe support bracket to engine lifting bracket bolts 25 Nm 18 lbf.ft
Front caliper brake hose banjo bolt 28 Nm 21 lbf.ft
Front caliper guide pin bolts 27 Nm 20 lbf.ft
Front caliper mounting bolts 100 Nm 74 lbf.ft
Front disc shield to hub screw 8.5 Nm 6.3 lbf.ft
Front disc to drive flange screws 5 Nm 3.7 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Handbrake cable to body and subframe bolts 22 Nm 16 lbf.ft
Handbrake cable retaining plate bolts 22 Nm 16 lbf.ft
Handbrake lever assembly to body bolts 22 Nm 16 lbf.ft
Hill Descent Control (HDC) switch bolt 5 Nm 3.5 lbf.ft
Master cylinder to servo nuts 25 Nm 18 lbf.ft
PAS oil cooler pipe bolts 10 Nm 7.5 lbf.ft
Primary and secondary brake pipe union nuts 17 Nm 12 lbf.ft
Rear wheel cylinder pipe union nut 17 Nm 12 lbf.ft
Rear wheel cylinder to backplate bolts 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 6 Nm 4.5 lbf.ft
Road wheel nuts 115 Nm 85 lbf.ft
Turbocharger intercooler pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolt 25 Nm 18 lbf.ft
Vacuum pump bolts
122 Nm 16 lbf.ft
Vacuum reservoir to mounting bracket nut 10 Nm 7.5 lbf.ft

TORQUE WRENCH SETTINGS
06-32
Heating and Ventilation
TORQUE DESCRIPTION METRIC IMPERIAL
Air intake hose and bracket assembly to fuel burning heater bolts (Td4) 10 Nm 7.5 lbf.ft
Exhaust pipe clamp bolts (Td4) 5 Nm 3.5 lbf.ft
Fuel burning heater to body bolts (Td4) 8 Nm 6 lbf.ft
Fuel burning heater to mounting bracket bolts (Td4) 8 Nm 6 lbf.ft
Heater to fascia nuts 8 Nm 6 lbf.ft
Heater to bulkhead bolt 8 Nm 6 lbf.ft
Evaporator to bulkhead bolts 8 Nm 6 lbf.ft

LIFTING AND TOWING
08-1
LIFTING AND TOWING
Jacking
The following instructions must be carried out before
raising the vehicle off the ground:
lUse a solid level surface.
lApply parking brake.
lSelect 1st. gear in main gearbox and ensure
HDC is not selected.
CAUTION: To avoid damage to under body
components of the vehicle, adhere to the
following jacking procedures:
DO NOT POSITION JACKS OR AXLE STANDS
UNDER THE FOLLOWING COMPONENTS:
lBumpers
lBrake or Fuel lines
lExhaust pipe
lSuspension components
lSteering rack and linkages
lFuel tank
lEngine sump
lGearbox
lIRD unit
Jack or support vehicle only on approved jacking
points as detailed in the following illustration:
Front (hydraulic jack) and side (vehicle jack) jacking
pointsSafety stand positions under longitudinal members
Rear (hydraulic jack) and side (vehicle jack) jacking
points
Vehicle jack
The jack provided with the vehicle is only intended to
be used in an emergency, for changing a tyre. Do
NOT use the jack for any other purpose. Refer to the
Owner's Handbook for vehicle jack location points
and procedure. Never work under a vehicle only
supported by the vehicle jack.
Hydraulic jack
A hydraulic jack with a minimum 1500 kg (3,300 lbs)
load capacity must be used.
WARNING: Do not work on or under a vehicle
supported only by a jack. Always support the
vehicle on safety stands.

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-1
CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
Capacities
The following capacities are only an approximation of
the amount of fluid required to fill the respective
system.
Capacities – UK/ROW
† An extra 420 cc (0.73 imp pt) is required for
vehicles with an air blast fluid cooler fitted.
* Refill capacity is approx. 0.7 litre (1.125 imp. pt)
less than the from dry figures.
Capacities – NAS
Component / system Capacity
Fuel tank:
Td4 Model
K1.8 and KV6 Models
⇒ Up to 03 Model Year
⇒ From 03 Model Year
KV6 Model
⇒ Up to 03 Model Year
⇒ From 03 Model Year59 litres (13 gallons)
59 litres (13 gallons)
64 litres (14.3 gallons)
59 litres (13 gallons)
64 litres (14.3 gallons)
Engine - Td4 (including oil cooler and oil filter):
⇒ Refill 6.8 litres (12 imp. pts)
⇒ Fill from dry 7.3 litres (12.9 imp. pts)
Engine - K1.8 (including filter):
⇒ Refill 4.5 litres (7.9 imp. pts)
⇒ Fill from dry 4.8 litres (8.4 imp. pts)
Engine - KV6 (including oil cooler and filter):
⇒ Refill 5.2 litres (9.125 imp. pts)
⇒ Fill from dry 6.0 litres (10.625 imp. pts)
Manual gearbox - PG1:
⇒ Refill 2.0 litres (3.5 imp. pts)
⇒ From dry 2.2 litres (3.9 imp. pts)
Manual gearbox - Getrag:
⇒ Refill 1.6 litres (2.875 imp. pts)
⇒ From dry 1.67 litres (3 imp. pts)
Automatic gearbox - JATCO:
⇒ Refill 4.0 litres (7 imp. pts)
⇒ From dry
†8.5 litres (15 imp. pts)
Intermediate Reduction
Drive1.1 litres (2 imp. pts)
Rear differential:
⇒ Maximum 830 ml (29.2 imp. fl. oz.)
⇒ Minimum 750 ml (26.4 imp. fl. oz.)
Power steering reservoir 335 cm
3
Cooling system - Td4 Engine – Fill from dry (with
reservoir)*:
⇒ Automatic - Up to 03
Model Year
⇒ Automatic - From 03
Model Year7.25 litres (12.8 imp. pts)
7.35 litres (13 imp. pts)
⇒ Manual 7.25 litres (12.8 imp. pts)
Cooling system - K1.8 Engine:
⇒ Fill from dry (with
reservoir)*5.8 litres (10.25 imp. pts)
Cooling system - KV6 Engine:
⇒ Fill from dry (with
reservoir)*7.8 litres (13.75 imp. pts)
Reservoir tank:
⇒ Maximum fill 0.44 litres (0.75 imp. pts)
⇒ Expansion tank volume 1.2 litres (2.125 imp. pts)
⇒ Gross expansion
capacity0.72 litres (1.27 imp. pts)
Windscreen washer
reservoir 4.0 litres (7 imp. pints)
Component / system Capacity
Fuel tank:
⇒ Up to 02.5 Model Year
⇒ From 02.5 Model Year15.6 US gallons
17.2 US gallons
Engine - KV6 (including oil cooler and filter):
⇒ Engine oil and filter
change11 US pts
⇒ Fill from dry 12.7 US pts
Automatic gearbox - JATCO:
⇒ Refill 8.5 US pts
⇒ From dry 18.2 US pts
Intermediate Reduction
Drive2.3 US pts
Rear differential:
⇒ Maximum
⇒ Minimum28.1 US fl. oz.
25.4 US fl. oz.
Power steering reservoir 335 cm
3
Cooling system - KV6 Engine:
⇒ Fill from dry (with
reservoir)17.82 US pts
Reservoir tank:
⇒ Maximum fill 0.93 US pts
⇒ Expansion tank volume 2.54 US pts
⇒ Gross expansion
capacity1.52 US pts
Windscreen washer
reservoir 8.5 US pts Component / system Capacity

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-2
Fluids
Fuel
Always use the following recommended fuels:
Petrol engines
Use unleaded petrol with a minimum octane rating of
95 RON to ENN 228 specification.
In an emergency (and only if the correct fuel is
unavailable), lower octane rated fuel can be used for
very limited periods of moderate, low speed
motoring, provided engine 'knocking' does not occur.
Fuels of 90 RON is used in certain markets; 90 RON
fuel can be used regularly ONLY if the engine has
been tuned specifically to suit low octane fuel.
Certain markets use fuel containing a 23% Ethanol
additive.
K1.8 and KV6 engines are also available for use with
a low octane leaded fuel specification in some
markets.
Diesel engines
Use a good quality diesel fuel or automotive gas oil
(AGO) conforming to EN 590 specification.
It is important that the sulphur content of diesel fuel
does not exceed 0.3%.
Ensure the fuel filter element is changed at the
recommended intervals.

+ MAINTENANCE, MAINTENANCE, Fuel
Filter - Diesel.
Brake Fluid
Use only DOT 4 brake fluid. DO NOT use brake fluid
of a different specification.
PAS fluid
Use Texaco 9226 fluid.Anti-freeze solutions
The overall anti-freeze concentration should not fall,
by volume, below 50% to ensure that the anti-
corrosion properties of the coolant are maintained.
Anti-freeze concentrations greater than 60% are not
recommended as cooling efficiency will be impaired.
Use Havoline Extended Life Coolant (XLC), or any
ethylene glycol based anti-freeze (containing no
methanol) with only Organic Acid Technology (OAT)
corrosion inhibitors, to protect the cooling system.
CAUTION: No other anti-freeze should be used
with Havoline Extended Life Coolant.
The cooling system should be drained, flushed and
refilled with the correct amount of anti-freeze
solution at the intervals given on the Service
Maintenance Check Sheet.
After filling with anti-freeze solution, attach a warning
label to a prominent position on the vehicle stating
the type of anti-freeze contained in the cooling
system to ensure that the correct type is used for
topping-up.
The following recommended quantities of anti-freeze
will provide frost protection to -36 °C (-33 °F):
Engine – Td4
Engine – K1.8
Engine – KV6
Concentration 50%
Amount of anti-freeze 3.75 litres
(6.625 imp. pts)
Concentration 50%
Amount of anti-freeze 2.9 litres
(5.125 imp. pts)
Concentration 50%
Amount of anti-freeze 3.9 litres
(6.875 imp. pts, )

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-3
Lubrication
The engine and other lubricating systems are filled
with high- performance lubricants giving prolonged
life.
CAUTION: Always use a high quality oil of the
correct viscosity range in the engine. The use of
oil of the incorrect specification can lead to high
oil and fuel consumption and ultimately to
damaged components.
Oil to the correct specification contains additives
which disperse the corrosive acids formed by
combustion and prevent the formation of sludge
which can block the oil ways. Additional oil additives
should not be used.
Always adhere to the recommended servicing
intervals.
Engine oil
Engine oil viscosity / temperature ranges are
indicated in the following table:
a0W/30; 5W/30
b0W/40, 50, 60; 5W/40, 50, 60
c10W/30
d10W/40, 50, 60
Engine oil – Td4 engine
Use 0W/30 or 5W/40, 50, 10W/30, 40, 60 oil meeting
ACEA A3/B3 specifications, and having a viscosity
band recommended for the temperature range of
your locality. Where oils to these European
specifications are not available, well known brands of
oils meeting API SH quality should be used.Engine oil – K1.8 engine
Use a 10W/40 oil meeting specification ACEA A2 or
A3.
Engine oil – KV6 engine – Non NAS models
Use a 10W/40 oil meeting specification ACEA A2 or
A3.
Engine oil – KV6 engine - NAS models
Use a 5W/40 fully synthetic oil meeting specification
ACEA A3. Where oils to these European
specifications are not available, well known brands of
oils meeting API SH quality should be used.
Gearbox oil
Use of gearbox oils other than those specified may
result in serious damage to the gearbox.
Manual Gearbox – PG1 and Getrag
Use OPEL B 0400063 for refill or topping-up.
Automatic Gearbox – JATCO
Use Texaco N402 fluid for refill or topping-up.
Intermediate Reduction Drive
Texaco S5 75W90; Synthetic oil or equivalent,
meeting: API GL5
Rear Differential
Multigear 80W/90 ETL; Specification: API GL5
Gear linkage - Manual
Use grease containing 3% Molybdenum Disulphide.
General Greasing
Use Multipurpose Lithium Base Grease NLGI
consistency No. 2.
Bonnet latch
Lubricate cable and latch with oil.

MAINTENANCE
10-10 MAINTENANCE
Fuel Filter - Petrol
Replace
1.Renew fuel filter.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Filter - main.
Fuel Filter - Diesel
Replace
1.Replace fuel filter element.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Filter - main - up to 03MY.
Fuel Pump and Filter assembly - Diesel -
03 Model Year onwards
Remove
1.Remove fuel pump and filter assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Pump and filter assembly - from
03MY.
2.Remove all traces of dirt from fuel pump and
filter assembly.
WARNING: Suitable eye protection must be
worn.
Refit
1.Fit fuel pump and filter assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Pump and filter assembly - from
03MY.
Fuel Sedimenter - Diesel - 03 Model Year
onwards
Drain
1.Position suitable container beneath
sedimenter.
2.Loosen but do not remove sedimenter drain
plug.
WARNING: Suitable hand protection must
be worn.
3.Allow sedimenter to drain until fuel, free from
water, flows from drain hole.
4.Tighten sedimenter drain plug.