fuel LAND ROVER FREELANDER 2001 Repair Manual

EMISSION CONTROL
REPAIRS 17-1-3
REPAIRS
Valve - depression limiter - Td4
$% 17.10.25
Remove
1.Disconnect battery earth lead.
2.Remove air cleaner element

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
3.Disconnect multiplugs from injectors.
4.Remove 3 screws and move injector harness
aside.
5.Remove 4 Allen screws and remove valve with
filter assembly. Discard seals.Refit
1.Clean filter with valve housing and mating
faces.
2.Use new seals, fit filter and valve assembly,
tighten Allen screws to 8 Nm (6 lbf.ft).
3.Position injector harness and secure with
screws.
4.Connect multiplugs to injectors.
5.Fit air cleaner element.
+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
6.Connect battery earth lead.
M17 0280
M17 0281

EMISSION CONTROL
REPAIRS 17-1-7
Valve - EGR - Td4
$% 17.45.01
Remove
1.Disconnect battery earth lead.
2.Remove intake ducting assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
3.Disconnect vacuum hose from EGR valve.
4.Loosen screw and remove clamp EGR pipe to
valve.
5.Remove 4 bolts and EGR valve. Discard seal.Refit
1.Clean EGR valve and mating face on inlet
manifold.
2.Clean EGR pipe flange and EGR valve mating
face.
3.Fit new seal to inlet manifold.
4.Fit EGR valve and tighten bolts evenly to 10 Nm
(7.5 lbf.ft).
5.Fit EGR pipe clamp and tighten screw.
6.Connect vacuum hose to EGR valve.
7.Fit intake ducting assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
8.Connect battery earth lead.

EMISSION CONTROL
REPAIRS 17-1-9
Thermal valve - exhaust gas
recirculation (EGR) - Td4 Automatic
transmission (hot climates) - from 03 MY
$% 17.45.07
Remove
1.Disconnect the battery earth lead.
2.Release thermal valve coolant hose from clips.
3.Position container to collect coolant.
4.Release 3 clips securing coolant hoses to the
EGR thermal valve.
5.Disconnect coolant hoses from the EGR
thermal valve and remove the thermal valve.
Refit
1.Position the EGR thermal valve and connect
coolant hoses.
2.Secure hoses with clips.
3.Fit thermal valve coolant hose into clips.
4.Connect the battery earth lead.
5.Refill the cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
Cooler - EGR - Td4
$% 17.45.40
Remove
1.Disconnect battery earth lead.
2.Remove camshaft cover.

+ ENGINE - Td4, REPAIRS, Gasket -
camshaft cover.
3.Mark EGR pipe and cooler to aid refit.
4.Loosen clamps EGR pipes to cooler and move
clamps aside.
5.Remove pipe, EGR cooler to EGR valve.
6.Remove bolt securing fuel rails to support
bracket.
7.Remove bolt securing turbocharger outlet pipe
to support bracket.
8.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
M170364

M17 0283

EMISSION CONTROL
17-1-10 REPAIRS
9.Remove bolt securing turbo outlet pipe to upper
coolant rail.
10.Remove 2 bolts securing pipe support bracket
to engine lifting bracket, remove support
bracket.
11.Release clip and remove vacuum hose.
12.Remove 3 bolts securing EGR cooler to
cylinder head and lifting bracket.13.Lift EGR cooler from mounting and position a
container beneath coolant hoses.
14.Release clips and remove hoses from EGR
cooler allow coolant to drain.
15.Remove EGR cooler.
Refit
1.Position EGR cooler, connect coolant hoses
and fit clips.
2.Position EGR cooler to mounting, fit bolts and
tighten to 25 Nm (18 lbf.ft).
3.Position pipe support bracket to engine lifting
bracket, fit and tighten bolts to 25 Nm (18 lbf.ft).
4.Fit vacuum hose and tighten clip.
5.Fit bolt securing turbocharger pipe to coolant
rail and tighten to 25 Nm (18 lbf.ft).
6.Fit underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
7.Fit bolt securing turbocharger outlet pipe to
support bracket and tighten to 10 Nm (7.5
lbf.ft).
8.Fit bolt securing fuel rails to support bracket
and tighten to 10 Nm (7.5 lbf.ft).
9.Align EGR pipe to cooler fit clamp, but do not
fully tighten until camshaft cover is refitted.
10.Fit EGR pipe clamp and tighten screw.
11.Fit camshaft cover.

+ ENGINE - Td4, REPAIRS, Gasket -
camshaft cover.
12.Connect battery earth lead.
13.Top up cooling system.

+ MAINTENANCE, MAINTENANCE,
Cooling System and Intercooler.

EMISSION CONTROL
17-1-12 REPAIRS
Filter - fuel leak detection pump - KV6 -
NAS
$% 17.45.42
Remove
1.Disconnect battery earth lead.
2.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
3.Remove nut and release filter from bracket.
4.Release clip and remove filter from pipe.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
Refit
1.Fit filter to pipe and secure with clip.
2.Fit filter to bracket and tighten nut to 3 Nm (2.2
lbf.ft).
3.Fit wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
4.Connect battery earth lead.
Catalytic converter - RH - KV6 - NAS
$% 17.50.01
Remove
1.Position vehicle on 4 post ramp.
2.Disconnect battery earth lead.
3.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
4.Release pre catalyst H02S harness from clips.
5.Release and disconnect HO2S multiplug.
6.Remove intermediate pipe and silencer.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Intermediate
pipe - NAS.
7.Remove 3 bolts and remove LH heat shield.
M19 3484

ENGINE MANAGEMENT SYSTEM - SIEMENS
18-3-6 REPAIRS
Engine control module (ECM) - fuel - NAS
$% 18.30.03
Remove
1.Disconnect battery earth lead.
2.Remove 5 Allen screws and 'E' box cover.
3.Disconnect 5 multiplugs from engine ECM.4.Release 2 clips and remove ECM.
Refit
1.Fit ECM and connect multiplugs.
2.Fit 'E' box cover and tighten Allen screws to 2
Nm (1.5 lbf.ft).
3.Connect battery earth lead.
4.Initiate ECM using TestBook/T4.
CAUTION: The ECM can only be re-
programmed a maximum of 20 times.
M18 0665

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-1
FUEL DELIVERY SYST EM - PE TROL ADJUST ME NTS
Throttle cable - check and adjust - KV6
$% 19.20.05
Check
1.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Before adjusting cable, ensure that cable is
correctly routed and located.
Adjust
1.Release cable adjusting nut from abutment
bracket.2.Hold throttle cam in fully closed position.
3.Rotate adjusting nut until all slack is taken out
of inner cable and nut is in contact with rear
face of abutment bracket. Ensure throttle does
not open.
4.Fit throttle cable adjusting nut in abutment
bracket.
5.Operate throttle pedal and ensure that full
throttle pedal movement is available.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
19-2-2 ADJUSTMENTS
Throttle cable - check and adjust - K1.8
$% 19.20.05
Check
1.Before adjusting cable, ensure that cable is
correctly routed and located.
Adjust
1.Release cable adjusting nut from abutment
bracket.
2.Hold throttle cam in fully closed position.
3.Rotate adjusting nut until all slack is taken out
of inner cable and nut is in contact with rear
face of abutment bracket. Ensure throttle does
not open.
4.Fit throttle cable adjusting nut in abutment
bracket.
5.Operate throttle pedal and ensure that full
throttle pedal movement is available.
Fuel system - depressurise - KV6 - Non
NAS
$% 19.50.02
Check
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
3.Pull back cover from hose connector and
carefully release connector.
WARNING: Depressurise the system before
disconnecting any components. Fuel
pressure will be present in the system even
if the ignition has been switched off for
some time.
4.Secure connector once pressure has been
relieved.
5.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-3
Fuel system - depressurise - KV6 - NAS
$% 19.50.02
Check
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2. Up to 03MY: Remove nut and bolt securing coil
and position coil aside.
3.Remove schraeder valve cap.
4.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.5.Connect adapter LRT-19-006 to schraeder
valve.
6.Position opposite end of adapter LRT-19-006
into container, turn tap to release pressure.
7.Remove adapter LRT-19-006 from schraeder
valve.
8.Fit cap to schraeder valve.
9. Up to 03MY: Fit and tighten nut and bolt
securing coil.
10.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
19-2-4 ADJUSTMENTS
Fuel system - depressurise - K1.8
$% 19.50.02
Check
1.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
2.Disconnect fuel feed hose from fuel rail.
3.Connect feed hose to fuel rail once pressure
has relieved.
Fuel system - pressure test - KV6 - Non
NAS
$% 19.50.13
Check
1.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
3.Disconnect fuel inlet hose from fuel rail pipe.
4.Connect adaptor LRT-19-013, to pressure
gauge LRT-19-004 .
5.Position pressure gauge LRT-19-004, connect
to fuel inlet hose and to fuel rail pipe, securing
pressure gauge hose to fuel rail pipe with clip.
6.Start engine. Pressure at idle = 3.4 bar. If
pressure below 3.4 bar suspect the following in
order: fuel hoses, filter, regulator and pump.
7.Stop engine.
8.Release clip and disconnect LRT-19-004
pressure gauge from fuel inlet hose and fuel rail
pipe.
9.Disconnect adaptor LRT-19-013 from LRT-19-
004 pressure gauge.
10.Connect fuel inlet hose to fuel rail pipe.
11.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
M19 3247A
LRT-19 - 013
LRT -19- 004