ABS LAND ROVER FREELANDER 2001 Repair Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 2001, Model line: FREELANDER, Model: LAND ROVER FREELANDER 2001Pages: 1007, PDF Size: 23.47 MB
Page 555 of 1007
BRAKES
70-6 REPAIRS
Hose - front - primary - LH
$% 70.15.02
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel(s).
3.Loosen brake pipe union to hose and release
union.
CAUTION: Always fit plugs to open
connections to prevent contamination.
4.Remove 2 clips securing hose to valance and
damper bracket.
5.Release clips securing ABS sensor lead to
brake hose.
6.Remove banjo bolt securing brake hose to
calliper and collect sealing washers.
7.Remove brake hose and plug brake calliper.Refit
1.Remove plugs and clean brake pipe male end.
2.Position hose to support brackets and secure
with clips.
3.Clean banjo bolt, hose and calliper mating
faces.
4.Using new sealing washers, align hose to
calliper, fit banjo bolt and tighten to 28 Nm (21
lbf.ft)
5.Align hose to brake pipe and tighten union to 17
Nm (12 lbf.ft).
6.Secure ABS sensor lead to brake hose.
7.Bleed brakes.
+ BRAKES, ADJUSTMENTS, Brake
bleed.
8.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
9.Remove stand(s) and lower vehicle.
Page 556 of 1007
BRAKES
REPAIRS 70-7
Hose - rear
$% 70.15.17
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Release clips securing ABS sensor lead to
brake hose.
4.Loosen brake pipe unions to brake hose and
release unions.
CAUTION: Always fit plugs to open
connections to prevent contamination.
5.Remove 2 clips securing hose to valance and
damper bracket.
6.Remove brake hose.Refit
1.Remove plugs and clean brake pipe male end.
2.Position hose to support brackets and secure
with clips.
3.Align brake pipes and tighten unions to 17 Nm
(12 lbf.ft).
4.Secure ABS sensor lead to brake hose.
5.Bleed brakes.
+ BRAKES, ADJUSTMENTS, Brake
bleed.
6.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
7.Remove stands and lower vehicle.
Page 557 of 1007
BRAKES
70-8 REPAIRS
Cylinder - master - tandem - LHD
$% 70.30.08
Remove
1.Disconnect brake fluid level multiplug.
2.Position cloth under master cylinder to absorb
spilled fluid.
CAUTION: Brake fluid will damage paint
finished surfaces. If spilled, immediately
remove fluid and clean area with water.
3.Disconnect secondary system pipe union from
master cylinder.
4.Disconnect primary system pipe union from
master cylinder.
CAUTION: Always fit plugs to open
connections to prevent contamination.
5.Remove Torx bolt securing master cylinder
reservoir to access master cylinder retaining
nut.6.Remove and discard 2 nuts securing master
cylinder to servo, remove master cylinder.
7.Refit Torx bolt to reservoir.
8.Remove and discard sealing ring.
Refit
1.Clean master cylinder and servo mating
surfaces.
2.Remove Torx bolt securing brake fluid reservoir
to master cylinder.
3.Fit new sealing ring to master cylinder.
4.Align push rod and position master cylinder to
servo.
5.Fit new nuts and tighten 25 Nm (18 lbf.ft).
6.Fit Torx bolt securing reservoir to master
cylinder and tighten to 8 Nm (6 lbf.ft).
7.Clean brake pipe unions.
8.Connect primary and secondary brake pipes
and tighten unions 17 Nm (12 lbf.ft).
9.Connect fluid level switch multiplug.
10.Bleed brakes.
+ BRAKES, ADJUSTMENTS, Brake
bleed.
M70 1067
Page 558 of 1007
BRAKES
REPAIRS 70-9
Cylinder - master - tandem - RHD
$% 70.30.08
Remove
1.Disconnect brake fluid level multiplug.
2.Disconnect servo vacuum pipe from inlet
manifold and release vacuum pipe from master
cylinder reservoir.
3.Position cloth under master cylinder to absorb
spilled fluid.
CAUTION: Brake fluid will damage paint
finished surfaces. If spilled, immediately
remove fluid and clean area with water.
4.Disconnect secondary system pipe union from
master cylinder.
5.Disconnect primary system pipe union from
master cylinder.
CAUTION: Always fit plugs to open
connections to prevent contamination.
6.Remove nut and 2 bolts securing master
cylinder reservoir.7.Remove and discard 2 nuts securing master
cylinder to servo, remove master cylinder.
8.Remove and discard sealing ring.
Refit
1.Clean master cylinder and servo mating
surfaces.
2.Fit new sealing ring to master cylinder.
3.Align push rod and position master cylinder to
servo.
4.Fit new nuts and tighten 25 Nm (18 lbf.ft).
5.Align reservoir, fit nut and bolts and tighten to 6
Nm (4.5 lbf.ft).
6.Clean brake pipe unions.
7.Connect primary and secondary brake pipes
and tighten unions 17 Nm (12 lbf.ft).
8.Connect servo vacuum pipe to inlet manifold
and secure to master cylinder reservoir.
9.Connect fluid level switch multiplug.
10.Bleed brakes.
+ BRAKES, ADJUSTMENTS, Brake
bleed.M70 1071
Page 574 of 1007
BRAKES
REPAIRS 70-25
Switch - low fluid level
$% 70.65.06
Remove
1.Disconnect brake fluid level multiplug.
2.Release retaining pin and remove fluid level
switch.
Refit
1.Clean brake fluid level switch.
2.Fit brake fluid level switch.
3.Connect multiplug to brake fluid level switch.
Sensor & harness - front wheel - RH
$% 70.65.29
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove front wheel arch liner.
+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
4.Locate ABS sensor harness on inner wing.
5.Release ABS sensor multiplug from body clip
and disconnect multiplug.
6.Release grommet from wing valance and pull
harness through.
Page 575 of 1007
BRAKES
70-26 REPAIRS
7.Release 2 grommets from wing valance and
damper brackets
8.Release harness from brake hose clips.
9.Remove bolt securing ABS sensor to hub, if
fitted.
10.Release ABS sensor from hub.
11.Remove ABS sensor and harness.
12.Remove bush from front hub.Refit
1.Clean ABS sensors and mating faces.
2.Fit new bush to front hub.
3.Apply anti-seize grease to sensor.
4.Fit sensor to hub, ensure sensor is fully seated
in hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
5.Fit and tighten bolt securing ABS sensor to hub,
if fitted.
6.Secure harness grommets to brackets.
7.Pass sensor harness through wing valance and
secure grommet.
8.Ensure 'O' ring is in place and connect sensor
multiplug to body harness.
9.Secure multiplug in body clip.
10.Secure harness to brake hose clip.
11.Fit front wheel arch liner.
+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
13.Remove stand and lower vehicle.
14.To ensure correct operation, the ABS system
MUST be tested using TestBook/T4.
Page 576 of 1007
BRAKES
REPAIRS 70-27
Sensor & harness - front wheel - LH
$% 70.65.30
Remove
1.Remove battery carrier.
+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove front wheel arch liner.
+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
5.Locate ABS sensor harness on inner wing.
6.Release ABS sensor multiplug from body clip
and disconnect multiplug.
7.Release grommet from wing valance and pull
harness through.8.Release 2 grommets from wing valance and
damper brackets
9.Release harness from brake hose clips.
10.Remove bolt securing ABS sensor to hub, if
fitted.
11.Release ABS sensor from hub.
12.Remove ABS sensor and harness.
13.Remove bush from front hub.
Page 577 of 1007
BRAKES
70-28 REPAIRS
Refit
1.Clean ABS sensors and mating faces.
2.Fit new bush to front hub.
3.Apply anti-seize grease to sensor.
4.Fit sensor to hub, ensure sensor is fully seated
in hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
5.Fit bolt securing ABS sensor to hub, if fitted.
6.Secure harness grommets to brackets.
7.Pass sensor harness through wing valance and
secure grommet.
8.Ensure 'O' ring is in place and connect sensor
multiplug to body harness.
9.Secure multiplug in body clip.
10.Secure harness to brake hose clip.
11.Fit front wheel arch liner.
+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12.Fit battery carrier.
+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
13.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
14.Remove stand and lower vehicle.
15.To ensure correct operation, the ABS system
MUST be tested using TestBook/T4.
Page 578 of 1007
BRAKES
REPAIRS 70-29
Sensor & harness - rear wheel
$% 70.65.31
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Release ABS sensor multiplug from body clip
and disconnect multiplug.
4.Release ABS sensor harness from 3 grommets
on suspension and body brackets.
5.Release harness from clip on rear brake hose.6.Remove bolt securing ABS sensor to hub, if
fitted.
7.Release sensor from rear hub and remove
sensor and harness.
8.Remove bush from rear hub.
Refit
1.Clean sensor and rear hub mating faces.
2.Fit new bush to rear hub.
3.Apply anti-seize grease to sensor.
4.Fit sensor to hub, ensure sensor is fully seated
in hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
5.Fit bolt securing ABS sensor to hub, if fitted.
6.Ensure 'O' ring is in place and connect sensor
multiplug to body harness.
7.Secure multiplug in body clip.
8.Secure harness grommets to brackets.
9.Secure harness to brake hose clip.
10.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
11.Remove stands and lower vehicle.
12.To ensure correct operation, the ABS system
MUST be tested using TestBook/T4.
Page 579 of 1007
BRAKES
70-30 REPAIRS
Modulator unit
$% 70.65.49
Remove
1. Td4 and KV6 models: Remove engine
accoustic cover if fitted.
+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
2. Td4 and KV6 models: Release and remove air
intake hose.
3. Td4 and KV6 models: Release clip securing
harness and intake duct to body.
4. Td4 and KV6 models: Lift duct from body,
release clip from washer reservoir filler hose.
5. Td4 and KV6 models: Release and remove air
intake duct.
6. Td4 models: Loosen 2 clips and remove
intercooler outlet hose.7.Remove 2 bolts securing PAS oil cooler pipes.
8.Release PAS reservoir from mounting bracket
and position aside.
9.Release catch and disconnect ABS modulator
multiplug.
10.Position cloth under modulator to absorb fluid
spillage.
CAUTION: Brake fluid will damage paint
finished surfaces. If spilled, immediately
remove fluid and clean area with water.
11.Disconnect 2 inlet brake pipes unions from ABS
modulator.
12.Disconnect 4 outlet brake pipes unions from
ABS modulator.
CAUTION: Always fit plugs to open
connections to prevent contamination.
13.Remove 3 bolts securing ABS modulator to
mounting bracket.
14.Release and remove ABS modulator from
mounting bracket.
M70 1085
M70 1083
M70 1088