roof LAND ROVER FREELANDER 2001 Repair Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 2001, Model line: FREELANDER, Model: LAND ROVER FREELANDER 2001Pages: 1007, PDF Size: 23.47 MB
Page 853 of 1007
CORROSION PREVENTION AND SEALING
77-4-22 SEALING
Seam sealer on fuel filler and roof - 3 door
Seams symmetrically opposite to those shown are also treated. On roof seams, sealant to be finished flush to surface
forward of points 'A' and rearward of points 'B'.
Page 854 of 1007
CORROSION PREVENTION AND SEALING
SEALING 77-4-23
Seam sealer on fuel filler and roof - 5 door
Seams symmetrically opposite to those shown are also treated. On roof seam, sealant to be finished flush to surface
forward of point 'A'.
Page 950 of 1007
SECURITY
REPAIRS 86-4-3
Immobilisation - electronic control unit
(ECU) -
$% 86.77.07
Remove
1.Disconnect battery earth lead.
2.Remove fascia.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
3.Remove 2 plastic nuts securing immobilisation
ECU and disconnect multiplug. Remove
immobilisation ECU.
Refit
1.Connect multiplug to immobilisation ECU.
2.Position ECU, fit and tighten 2 plastic nuts.
3.Fit fascia.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
4.Connect battery earth lead.
5.Initiate using TestBook/T4.
Sensor - volumetric - alarm system - 3
door
$% 86.77.29
Remove
1.Remove roof lamp lens.
2.Remove 2 screws, release roof lamp and
disconnect multiplug.
3.Release headlining rear finisher from roof panel
and remove finisher.
M86 5633
Page 951 of 1007
SECURITY
86-4-4 REPAIRS
4.Release door aperture seals to release
headlining.
5.Release 3 studs securing rear edge of
headlining to roof panel.
6.Remove 4 screws securing headlining to 'B'
posts.
7.Release 2 studs securing sides of headlining to
body.
8.Lower front edge of headlining.
9.Release sun roof seal.
10.Remove 2 screws from volumetric sensor.
11.Disconnect multiplug from volumetric sensor
and remove.Refit
1.Position volumetric sensor and connect
multiplug.
2.Fit sensor and secure with screws.
3.Fit headlining to 'B' posts and secure with
screws.
4.Secure headlining behind rear vent rubbers.
5.Fit headlining rear finisher.
6.Fit door aperture seals.
7.Fit headlining to sun roof seal.
8.Position roof lamp and connect multiplug.
9.Fit roof lamp and secure with screws.
10.Fit lens to roof lamp.
Page 952 of 1007
SECURITY
REPAIRS 86-4-5
Module (ECU) - volumetric - alarm
system - 5 door - without sunroof
$% 86.77.29
Remove
1.Remove LH rear quarter upper trim casing.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
2.Remove LH 'A' post upper finisher.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
3.Release front and rear LH door seals.
4.Remove screw covers and screws from both
LH grab handles and remove grab handles.
5.Remove LH sun visor.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.6.Remove trim stud securing forward edge of
headlining.
7.Remove 2 trim studs securing centre of
headlining.
Page 954 of 1007
SECURITY
REPAIRS 86-4-7
Refit
1.Fit volumetric sensor and secure with screws.
2.Connect multiplug to sensor.
3.Raise headlining and secure with trim studs.
4. Up to 04MY: Position front interior lamp and
connect multiplug.
5. Up to 04MY: Fit Torx bolts securing interior
lamp and tighten to 6 Nm (4.4 lbf.ft).
6. Up to 04MY: Fit lens to front interior lamp.
7. From 04MY: Position front interior lamp and
connect multiplug.
8. From 04MY: Fit and secure front interior lamp
to headlining.
9.Position 'B/C' post upper finisher and secure
with clips.
10.Fit sun visor.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
11.Fit grab handles, tighten screws and fit screw
covers.
12.Fit 'A' post upper finisher.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
13.Fit rear quarter upper trim casing.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
14.Secure front and rear door seals.
Module (ECU) - volumetric - alarm
system - 5 door - with sunroof
$% 86.77.29
Remove
1.Release front and rear door aperture seals.
2.Remove 'A' post upper finishers.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
3.Remove screw covers, remove 6 screws
securing front and both rear grab handles and
remove grab handles.
4.Remove grab handle blanking plugs.
Page 955 of 1007
SECURITY
86-4-8 REPAIRS
5.Release and remove sun roof finisher.
6.Remove both sun visors.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
7.Remove trim stud securing forward edge of
headlining.8. Up to 04MY: Remove lens from front interior
lamp.
9. Up to 04MY: Remove 2 Torx screws securing
front interior lamp to body.
10. Up to 04MY: Release front interior lamp from
headlining, disconnect multiplug and remove
lamp.
11. From 04MY: Working from lamp forward edge,
release front interior lamp from headlining,
disconnect multiplug and remove lamp.
Page 956 of 1007
SECURITY
REPAIRS 86-4-9
12.Remove 2 trim studs securing centre of
headlining.
13.Release 8 clips securing both 'B/C' post upper
finishers and pull finishers clear of headlining.
14.Carefully lower headlining to gain access to
volumetric sensor.15.Disconnect multiplug from volumetric sensor.
16.Remove 2 screws securing volumetric sensor
and remove sensor.
Refit
1.Fit volumetric sensor and secure with screws.
2.Connect multiplug to sensor.
3.Secure the headlining with trim studs.
4.Position 'B/C' post upper finisher and secure
with clips.
5.Fit sun visors.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
6.Fit 'A' post upper finishers.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
7.Fit grab handles, tighten screws and fit screw
covers.
8.Fit grab handle blanking plugs.
9. Up to 04MY: Position front interior lamp and
connect multiplug.
10. Up to 04MY: Fit Torx bolts securing interior
lamp and tighten to 6 Nm (4.4 lbf.ft).
11. Up to 04MY: Fit lens to front interior lamp.
12. From 04MY: Position front interior lamp and
connect multiplug.
13. From 04MY: Fit and secure front interior lamp
to headlining.
14.Position and secure sun roof finisher.
15.Secure front and rear door seals.
Page 967 of 1007
IN CAR ENTERTAINMENT
86-6-4 REPAIRS
Speaker - front
$% 86.50.15
Remove
1.Remove front door trim casing.
+ DOORS, REPAIRS, Trim casing -
front door - 3 door.
+ DOORS, REPAIRS, Trim casing -
front door - 5 door - up to 04MY.
2.Remove 4 screws securing speaker to front
door.
3.Disconnect multiplug from speaker and remove
speaker.
Refit
1.Position speaker to door and connect multiplug.
2.Fit speaker to door and secure with screws.
3.Fit front door trim casing.
+ DOORS, REPAIRS, Trim casing -
front door - 3 door.
+ DOORS, REPAIRS, Trim casing -
front door - 5 door - up to 04MY.
Aerial - manual - 3 door
$% 86.50.18
Remove
1.Remove headlining.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
2.Remove 2 screws and release volumetric
sensor mounting bracket.
3.Remove nut securing coaxial cable to aerial
base.
4.Remove aerial base from roof panel and
remove rubber seal.
Refit
1.Position rubber seal and fit aerial base to roof
panel.
2.Connect coaxial cable and secure with nut.
3.Position volumetric sensor bracket and secure
with screws.
4.Fit headlining.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
Page 968 of 1007
IN CAR ENTERTAINMENT
REPAIRS 86-6-5
Aerial - manual - 5 door
$% 86.50.18
Remove
1.Remove lens from front interior lamp.
2.Remove 2 bolts securing front interior lamp to
body.
3.Release interior lamp from headlining,
disconnect multiplug and remove lamp.
4.Remove nut securing coaxial cable to aerial
base.5.Remove aerial base from roof panel and
remove rubber seal.
Refit
1.Position rubber seal and fit aerial base to roof
panel.
2.Connect coaxial cable and secure with nut.
3.Position front interior lamp and connect
multiplug.
4.Fit front interior lamp to headlining and secure
with bolts.
5.Fit lens to rear interior lamp.