fuel LAND ROVER FREELANDER 2001 Workshop Manual

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-35
Fuel rail - KV6 - Non NAS
$% 19.60.04.99
Remove
1.Disconnect battery earth lead.
2.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
3. Up to 03MY: Note position of coil earth lead,
remove 3 nuts and 3 bolts securing ignition
coils to LH inlet manifold.
4. Up to 03MY: Remove ignition coils and
position aside.
5.Disconnect clips securing RH injector harness
to injector protection cover - if fitted or from
bosses on fuel rail.6.Remove 2 bolts securing protection cover - if
fitted - and RH fuel rail to RH inlet manifold,
remove cover.
7.Remove 2 bolts securing fuel rail to LH inlet
manifold.
8.Release clips and disconnect injector
multiplugs.
9.Release injectors from manifolds, raise fuel rail
assembly, disconnect 4 clips securing injector
harness to fuel rails and move harness aside.

FUEL DELIVERY SYSTEM - PETROL
19-2-36 REPAIRS
10.Remove fuel rail.
CAUTION: Always fit plugs to open
connections to prevent contamination.
11.Remove and discard 'O' rings from injectors.
Refit
1.Lubricate new 'O' rings with castor oil and fit to
injectors.
2.Remove plugs from inlet manifolds.
3.Position injector harness to LH fuel rail and
secure with clips.
4.Position injectors and fuel rail to inlet manifolds.
5.Connect multiplugs to injectors.
6.Position injector cover - if fitted to RH fuel rail
and secure injector harness to protection cover
or to bosses on fuel rail with clips.
7.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
8. Up to 03MY: Position ignition coils to LH inlet
manifold.
9. Up to 03MY: Position earth lead, fit nuts and
bolts securing ignition coils to LH inlet manifold
and tighten to 9 Nm (7 lbf.ft).
10.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
11.Connect battery earth lead.
Fuel rail - KV6 - NAS
$% 19.60.04.99
Remove
1.Disconnect battery earth lead.
2.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
3.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Using a 3/8" socket bar raise ancillary drive belt
tensioner and release drive belt from alternator
and PAS pump pulleys.
5.Remove nuts and bolts securing alternator.
6.Release alternator and place aside.

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-37
7. Up to 03MY: Note position of coil earth lead,
remove 3 nuts and 3 bolts securing ignition
coils to LH inlet manifold.
8. Up to 03MY: Remove ignition coils and
position aside.
9.Disconnect clips securing RH injector harness
to injector protection cover - if fitted or to bosses
on fuel rail.
10.Remove 2 bolts securing RH fuel rail to RH inlet
manifold.
11.Release clips and disconnect injector
multiplugs.12.Remove 2 bolts securing fuel rail to LH inlet
manifold.
13.Release clips and disconnect injector
multiplugs.
14.Release injectors from manifolds, raise fuel rail
assembly, disconnect 4 clips securing injector
harness to fuel rails and move harness aside.

FUEL DELIVERY SYSTEM - PETROL
19-2-38 REPAIRS
15.Remove fuel rail and discard 'O' rings
CAUTION: Always fit plugs to open
connections to prevent contamination.
Refit
1.Lubricate new 'O' rings with castor oil and fit to
injectors.
2.Remove plugs from inlet manifolds.
3.Position injector harness to injector protection
cover - if fitted or to bosses on fuel rail fuel rail
and secure with clips.
4.Position injectors and fuel rail to inlet manifolds.
5.Connect multiplugs to injectors.
6.Fit and tighten 4 bolts securing fuel rail to inlet
manifold to 8 Nm (6 lbf.ft).
7. Up to 03MY: Position ignition coils to LH inlet
manifold.
8. Up to 03MY: Position earth lead, fit nuts and
bolts securing ignition coils to LH inlet manifold
and tighten to 9 Nm (7 lbf.ft).
9.Position alternator and secure with nuts and
bolts, tighten to 45 Nm (33 lbf.ft).
10.Using a 3/8" square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
11.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
12.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
13.Connect battery earth lead.
Injector - KV6
$% 19.60.10
Remove
1.Disconnect battery earth lead.
2.Remove fuel rail.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - Non
NAS.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - NAS.
3.Remove clip securing injector to fuel rail.
4.Remove injector from fuel rail, remove and
discard 'O' ring from injector.
CAUTION: Always fit plugs to open
connections to prevent contamination.
Refit
1.Clean injector and mating face in fuel rail.
2.Remove cap from new injector and fit to old
injector.
3.Lubricate new 'O' ring with castor oil and fit to
injector.
4.Fit injector to fuel rail and secure with clip.
5.Fit fuel rail.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - Non
NAS.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - NAS.
6.Connect battery earth lead.

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-39
Injectors - set - K1.8
$% 19.60.12
Remove
1.Disconnect battery earth lead.
2.Release clip and disconnect vacuum pipe from
fuel pressure regulator.
3.Remove engine oil dipstick.
4.Position absorbent cloth beneath fuel rail.
5.Release fuel feed hose from fuel rail.
CAUTION: Always fit plugs to open
connections to prevent contamination.6.Remove 2 bolts securing fuel rail to inlet
manifold.
7.Release fuel rail and injectors from inlet
manifold.
8.Release and remove injector spacer.
9.Disconnect multiplug from injectors.
10.Remove the fuel rail complete with injectors.
11.Release spring clips securing injectors to fuel
rail and remove fuel injectors.
12.Remove and discard 2 'O' rings from each
injector.
13.Fit protective caps to each end of injectors.

FUEL DELIVERY SYSTEM - PETROL
19-2-40 REPAIRS
Refit
1.Remove protective caps from each injector.
2.Clean injectors and recesses in fuel rail and
inlet manifold.
3.Lubricate new 'O' ring with castor oil and fit to
injector.
4.Fit injectors to fuel rail and secure with spring
clips.
5.Position fuel rail assembly and connect injector
multiplugs.
6.Fit injector spacer.
7.Push each injector into inlet manifold.
8.Fit bolts securing fuel rail to inlet manifold and
tighten to 8 Nm ( 6 lbf.ft).
9.Connect fuel feed hose to fuel rail.
10.Fit engine oil dipstick.
11.Connect vacuum pipe to fuel pressure regulator
and secure with clip.
12.Connect battery earth lead.
Actuator unit - cruise control - KV6 - non
NAS
$% 19.75.05
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Disconnect vacuum hose from actuator.
4.Remove nut securing actuator to mounting
bracket.
5.Release operating rod from throttle cam and
remove actuator.
Refit
1.Position actuator and connect operating rod to
throttle cam.
2.Position actuator into mounting bracket, fit and
tighten nut.
3.Connect vacuum hose to actuator.
4.Check pull rod to retainer clearance, with lever
fully returned, pull rod should just be held by
retainer.
5.Release retainer by turning anti-clockwise,
eliminate clearance then rotate retainer half
turn clockwise. Check pull rod is just held and
rotate retainer a further quarter turn clockwise
to lock.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-41
Vacuum pump - cruise control - KV6 -
non NAS
$% 19.75.06
Remove
1.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
2.Release 3 rubber mountings securing vacuum
pump to battery carrier and remove vacuum
pump.
3.Remove 3 rubber mountings from vacuum
pump.
Refit
1.Fit rubber mountings to vacuum pump.
2.Position vacuum pump to battery carrier and
secure with rubber mountings.
3.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
Switch - cruise control - KV6 - up to 04MY
$% 19.75.30
Remove
1.Remove radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.
2.Remove selector knobs from heater controls.
3.Remove 2 screws securing heater control
finisher to heater controls and remove finisher.
4.Release cruise control switch, disconnect
multiplug and remove switch.
Refit
1.Position cruise control switch, connect
multiplug and secure switch.
2.Fit heater control finisher to heater controls and
secure with screws.
3.Fit heater control knobs.
4.Fit radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.

FUEL DELIVERY SYSTEM - PETROL
19-2-42 REPAIRS
Switch - engagement (on/off) - from
04MY
$% 19.75.30
Remove
1.Release 2 clips and remove fascia mounted
switch cover.
2.Remove 2 screws securing switch carrier to
fascia.
3.Release switch carrier from fascia and
disconnect switch multiplug.
4.Remove switch assembly from carrier.
Refit
1.Fit switch to carrier.
2.Connect multiplug to switch.
3.Secure switch carrier to fascia with screws.
4.Fit and secure switch cover.
Switch - multi-purpose
$% 19.75.33
Remove
1.Remove airbag module from steering wheel.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
2.Release cruise control switch leads from clip
and disconnect multiplug.
3.Remove 2 screws securing cruise control
switch and remove switch.
Refit
1.Fit cruise control switch and secure with
screws.
2.Connect switch multiplug and fit leads in clip.
3.Fit drivers airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
M19 3672

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-43
ECU - cruise control - KV6
$% 19.75.49
Remove
1.Slide RH front seat fully rearwards.
2.Remove 2 screws securing ECU cover.
3.Remove cover.
4.Release interface ECU from bracket and move
aside.
5.Remove 2 screws securing cruise control ECU.
6.Disconnect multiplug from ECU and remove
ECU.
Refit
1.Connect multiplug to ECU.
2.Position ECU and tighten screws.
3.Secure interface ECU to bracket.
4.Fit ECU cover and secure with screws.
5.Position seat to mid position.
Interface ECU - cruise control - KV6
$% 19.75.55
Remove
1.Slide RH front seat fully rearwards.
2.Remove 2 screws securing ECU cover.
3.Remove cover.
4.Release interface ECU from bracket,
disconnect multiplug and remove ECU.
Refit
1.Position ECU, connect multiplug and secure
ECU to bracket.
2.Fit ECU cover and secure with screws.
3.Position seat to mid position.

COOLING SYSTEM - K SERIES KV6
26-3-6 REPAIRS
Thermostat
$% 26.45.01
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
4.Remove 2 bolts securing RH fuel rail to inlet
manifold. Remove injector protection cover if
fitted.
5.Release 2 clips securing engine harness to rear
engine lifting bracket and bracket on RH inlet
manifold.
6.Release clip and disconnect bottom hose from
thermostat housing.
7.Loosen clip and disconnect heater hose from
thermostat housing.8.Release clip and disconnect top hose from
coolant elbow.
9.Remove bolt securing thermostat housing and
coolant elbow to cylinder block.
10.Remove coolant elbow from cylinder block.
11.Remove thermostat housing and coolant pipe
from cylinder block.
12.Release clip and remove coolant pipe from
thermostat housing.
13.Remove and discard 4 'O' rings from
thermostat housing, coolant elbow and coolant
pipe.
Refit
1.Lubricate new 'O' rings with rubber grease and
fit to sealing grooves in thermostat housing,
coolant elbow and coolant pipe.
2.Fit coolant pipe into thermostat housing, ensure
clip connectors are uppermost.
3.Position thermostat housing and coolant pipe
above cylinder block, engage coolant pipe in
cylinder block and press thermostat housing
firmly into position. Ensure mounting flange on
thermostat housing is aligned to bolt hole in
cylinder block.
4.Fit coolant elbow into cylinder block, press
firmly into place. Ensure mounting flange is
aligned correctly to thermostat housing flange.
5.Fit bolt to coolant elbow and thermostat
housing flanges. Tighten bolt to 18 Nm (13
lbf.ft).
6.Connect top hose to coolant elbow and secure
with clip.
7.Connect heater and bottom hoses to
thermostat housing, secure with clips.
8.Position and secure engine harness to brackets
with clips.
9.If fitted, position injector protection cover to RH
fuel rail, fit and tighten bolts to 9 Nm (7 lbf.ft).
10.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
11.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
12.Connect battery earth lead.