engine LAND ROVER FRELANDER 2 2006 Owner's Manual

DT C
Description Possible Cause Action
P2800-00 Trans mis s ion range sens or
B circui t (PRNDL i nput ) Incorrect adjus tment of t he
gear s elector lever cabl e Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t hat t he gear sel ect or lever cable is
correctl y adjus ted.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,
General Procedures ).
Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect
P2801-00
Trans mis s ion range sens or
B circui t range/performance Incorrect adjus tment of t he
gear s elector lever cabl e Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P2805-00
Trans mis s ion range sens or
A/B correl at ion Incorrect adjus tment of t he
gear s elector lever cabl e Int ernal t rans mi ss i on cont rol
modul e (TCM) fault U0001-00
High s peed cont rol ler area
network (CAN)
communicat ion bus CAN circuit : open circuit CAN circuit : s hort circui t to
each ot her CAN circuit : s hort circui t to
power CAN cont rol module fail ure Carry out a compl ete vehicle read for DTCs
indicati ng a CAN or module fault . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if a module i s s uspect.
U0100-00 Los t communicati on wi th
ECM "A" CAN circuit : open circuit CAN circuit : s hort circui t to
each ot her CAN circuit : s hort circui t to
power CAN cont rol module fail ure Carry out a compl ete vehicle read for DTCs
indicati ng a CAN or module fault . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if a module i s s uspect.
U0121-00 Cont rol ler area net work
(CAN) t rans mi ss ion cont rol
module ( TCM)/ant i-lock
brake s yst em (ABS) circuit
malfunct ion no
communicat ion CAN circuit : open circuit CAN circuit : s hort circui t to
each ot her CAN circuit : s hort circui t to
power CAN cont rol module fail ure Carry out a compl ete vehicle read for DTCs
indicati ng a CAN or module fault . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if a module i s s uspect.
U0300-00 Int ernal cont rol module
s oft ware i ncompat ibil it y Incorrect cont rol ler area
net work (CAN) configurat ion
ID
- incorrect
hardware/s oft ware level Check t hat t he modules are correct for the
vehicl e and that t he correct level of software is
ins tall ed. Reconfi gure t he CAN s yst em us i ng the
approved di agnos ti c s ys t em.
U0401-00 Invali d data recei ved from
engi ne cont rol module
(ECM) Incorrect s ignal from t he ECM Carry out a compl ete vehicle read for DTCs
indicati ng a cont rol ler area net work (CAN) or
ECM faul t. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
ECM is sus pect .
U0415-00 Invali d data recei ved from
the ant i-lock brake s ys tem
(ABS) control modul e The engine cont rol module
(ECM) has t he wrong code for
the i mmobil izer The ABS modul e (brake
control modul e (BCM)) has
the wrong code for the
immobi lizer Transmis si on cont rol module
(TCM) faul t Reprogramme the modules as neces sary. Refer
to the warranty pol icy and procedures manual if
a module i s s uspect.
U2100-00 Ini ti al confi gurati on not
compl ete Cont roll er area network
(CAN) circui t fault Init ial cent ral confi gurati on
has never been sent Check for ot her controll er area network (CAN)
DTCs or apparent ly unrel at ed cust omer
compl ai nts . Carry out a complet e vehi cl e DTC
read. Check t he CAN circui ts . Refer t o t he
el ect ri cal guides . Rect ify as neces s ary. Clear
the DTCs and t es t for normal operat ion. Check
correct cent ral car confi gurati on s oftware i s
ins tall ed. Reprogramme t he module as
neces sary.
U2101-00 Cont rol module
configurat ion i ncompat ible Cent ral car confi gurati on
parameter mi ss i ng or
corrupted Check correct central car configurat ion s oft ware
is i nst all ed. Reprogramme t he module as
neces sary.
U2023-00 Engi ne t orque s ignal Cont roll er area network
(CAN) circui t (between
engine cont rol module (ECM)
and trans mi ss i on cont rol
modul e (TCM)): open ci rcuit CAN circuit (between ECM
and TCM): s hort circui t CAN module fault Carry out a compl ete read for related DTCs .
Rect ify as neces s ary. Check t he CAN circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
U2105-11 Swit ch pack s i gnal "A" Shi ft l ock s olenoid ci rcuit
fault : s hort ci rcuit t o ground Gear s elector module (GSM)
fault Check t he GSM and circui ts . Refer t o t he
el ect ri cal guides . Rect ify as neces s ary. Refer to
the warrant y pol icy and procedures manual if
the GSM is s us pect .

ItemPart NumberDescription
1-Engine Type / Capacit y / Power2-Gros s Vehicle W eight
3-Gros s Train W eight
4-Occupancy5-Vehicle VIN Number
6-Buil d Date
VIN number - UK, EU and ROW (vehicles built up to 2010MY)
VIN PositionCharacterIdentifies1 - 3 - W orld ident ifierSALLand Rover (UK)
4 - Vehi cl e t ypeFFreelander 2
5 - Clas sAStandard6 - Body Type24 Door
6 - Body Type4Commercial
7 - Transmis s ion and St eering3RHD, Aut omat ic t rans mis s ion7 - Transmis s ion and St eering4LHD, Aut omati c t ransmis s ion
7 - Transmis s ion and St eering7RHD, Manual t rans mis s ion
7 - Transmis s ion and St eering8LHD, Manual transmis s ion8 - Engi neA3.2L Petrol
8 - Engi neB2.2L Di es el
8 - Engi neC2.2L Di es el wit h cDPF9- Check Digit4Deri ved by calculat ion: 0-9 or X
10 - Model year72007
10 - Model year82008

VIN PositionCharacterIdentifies
9 - Check digi t4Deri ved by calculat ion: 0-9 or X
10 - Model year8200810 - Model year92009
11 - Pl antHHalewood
12 -17 - Serial number100314Unique s ix di git s eri al number
VIN number - NAS and Canada (vehicles built from 2010MY)
VIN PositionCharacterIdentifies
1 - 3 - W orld ident ifierSALLand Rover (UK)
4 - Model rangeFLR25 - Clas sPNAS SE
5 - Clas sRNAS HSE
5 - Clas sSNAS SE+Lux pack5 - Clas sTNAS HSE+Lux pack
6 - Body Type24 Door
7 - Transmis s ion and St eeringBLHD, Aut omati c t ransmis s ion8 - Engi neN3.2L Petrol, ULEV 2 NAS
9 - Check digi t4Deri ved by calculat ion: 0-9 or X
10 - Model yearA201010 - Model yearB2011
10 - Model yearC2012
11 - Pl antHHalewood12 -17 - Serial number100314Unique s ix di git s eri al number
2.0 Liter Petrol Engine Serial Number
The 2.0 Li ter Petrol Engi ne Serial Number is st amped on t he RH s ide of t he cylinder block.
2.2 Liter Diesel Engine Serial Number

The 2.2 Li ter Di es el Engi ne Seri al Number i s s tamped on t he RH si de of the cyli nder block.
3.2 Liter Petrol Engine Serial Number
The 3.2 Li ter Petrol Engi ne Serial Number is et ched into the LH s ide of t he engi ne block.
Automatic Transmission Serial Number
The Automat ic Trans mi s si on Serial Number is st amped on t he LH s ide of t he t rans mis s ion cas ing.
Manual Transmission Serial Number

Publ is hed: 24-Jun-2011
Jacking and Lifting - Jacking
Des cript ion and Operat ion
General
W ARNING: The foll owing i nst ructi ons mus t be adhered to before rais i ng the vehicle off t he ground:
Posi ti on vehi cl e on a sol id, level surface.Apply t he parking brake.Select 'P' - PARK on automat ic t rans mis s ion sel ect or.Select 'N' - Neutral on manual t rans mis s ion.
W ARNING: If t he dri ve s haft(s ) are t o be di sconnect ed, i t wil l be neces s ary t o rai s e all four wheels off the ground inorder t hat t he s haft (s ) can be rot ated. DO NOT us e the cus tomer jack and ens ure that t he vehi cl e is adequatel y s upport edon axle s t ands . W i th the vehicle rai sed, it will be necess ary to releas e t he park brake and sel ect Neutral - 'N' in the mai nt ransmis s ion t o enabl e t he dri ve s haft(s ) to be rot ated.
• CAUTIO NS:
To avoid damage t o t he underbody components of t he vehi cle, the foll owing i ns t ructions mus t be adhered to:
Do not pos it ion jacks or axle s t ands under the foll owing component s :
Body s truct ure ot her t han any approved jacki ng or li ft ing point sRear subframeBumpersFuel l inesFuel t ankBrake l inesFront or rear s uspens ion armsSteering l inkageRear di fferenti al uni tTrans mis s ionEngi ne oil pan - See not e below
• NOTE: For certain repair operat ions, i t may be necess ary to support t he engine under t he oil pan. In thi s cas e, a bl ock ofhardwood or a rubber pad mus t be pos it ioned on t he jack li ft ing pad t o protect the oi l pan.
Hydraulic jack
• W ARNINGS:
Before commenci ng work on undersi de of vehi cl e, ens ure that axle s t ands are correctly pos it ioned and vehi cle i ss ecurel y s upported.
Al ways chock the rear wheel s when jacking t he front of the vehicle.
A hydrauli c jack wi th a mi ni mum li ft ing capacit y of 1500 kg, (3,300 l bs) must be us ed.
Raising and Supporting the Vehicle
To as si s t in rais ing the vehicle, us e t he cus t omer jacki ng poi nts on the s i ll or on t he trolley jack pos i ti on at the rear of t hefront subframe as indicated i n t he fol lowing ill ust rat ions .
Raising the front of the vehicle
W ARNING: Always chock t he rear wheels when jacki ng the front of t he vehi cl e.
Apply t he parking brake.
Select 'P' - Park on aut omat ic trans mi s si on s el ect or.
Select 'N' - Neutral on manual t rans mis s ion.

Publi s hed: 11-May-2011
Jacking and Lifting - Vehicle Recovery
Des cript ion and Operat ion
Towing Points
CAUTION: The s ingle towi ng poi nts at t he front and rear of t he vehi cl e are des igned for vehicl e recovery purpos esonly and mus t NOT be used to t ow a trail er or caravan.
The front towi ng eye is acces s ibl e aft er releas ing t he 2 t oggle fast eners s ecuring the t owing eye acces s panel andremovi ng the panel.
CAUTION: Ens ure t hat during t owing, the towi ng att achment does not contact t he bumper.
The rear t owing eye i s acces si ble after rel eas i ng the 2 toggle fas teners securi ng the towing eye access panel and removingt he panel.
CAUTION: This t owing eye s hould onl y be us ed for t owing another vehi cl e or for recovery purpos es .
Towing the vehicle on four wheels
• W ARNINGS:
Ens ure t hat the remote cont rol remai ns docked whil s t the vehicle is being towed. Removi ng the remot e cont rol wi llengage t he s t eering l ock, which wi ll prevent the vehicle from s t eering correct ly.
If the engine cannot be run whi ls t t he vehi cl e i s bei ng t owed, t here wi ll be no power as si s tance for t he s teeri ng orbrakes. Thi s wil l res ult in greater effort bei ng required to st eer or sl ow t he vehi cl e, and greatl y increas ed s toppingdis t ances.
• CAUTIO NS:
The vehicle s hould onl y be t owed wit h four wheels on the ground. Towing wi th two wheel s on t he ground wi ll res ultin serious damage t o t he trans mi s si on.
The vehicle s hould onl y be t owed for a maxi mum of 80 km (50 mil es), at a maximum s peed of 80 km/h (50 mph).Towing for a great er di st ance, or at a higher s peed may res ult i n s eri ous damage t o t he t rans mis s ion.
• NOTE: The recommended recovery met hod is to rais e al l four wheel s.
Towing procedure
1. The vehi cl e s houl d be parked on firm level ground, wi th t he park brake on, and the gear s el ect or in P if an aut omati cgearbox is fit t ed.
2. Secure the towing at t achment from the recovery vehicle to the front t owing eye.
CAUTION: Leavi ng the ignit ion s wi tched on for extended peri ods wil l caus e the bat tery t o drai n.
3. Dock the remote cont rol, and s wi tch on t he igni ti on.
4. Appl y t he foot brake, and s el ect neutral.
5. W i th the foot brake s t ill appli ed, releas e the park brake.

Publi s hed: 11-May-2011
Maintenance Schedules - Maintenance Schedules - Gasoline Engines
Des cript ion and Operat ion
Under Bonnet View
ItemPart NumberDescription1-Coolant expans ion t ank
2-Brake flui d res ervoir (LH drive i llus t rated - RH dri ve on oppos i te si de)
3-Engine oi l fil ler cap4-Power s teeri ng res ervoir
5-Engine oi l l evel i ndi cat or
6-W indscreen washer fl uid res ervoi r
Maintenance Operations
CAUTION: Not e that t he 'A' and 'B' Service Interval s li s ted on the 'Maintenance Check Sheet' for vehicles operat ingunder arduous condi ti ons , vary from t hos e s pecifi ed for vehicles operat ing under normal condit ions . Reference mus tt herefore, always be made to the 'Arduous Condi ti ons secti on for vehicles operat ing under thes e condi ti ons .
Unles s s tat ed otherwis e, the foll owi ng operati ons mus t be carri ed out at every s ervice int erval.
Battery

For addit ional informat ion, refer t o: Parking Brake Cabl e Adjus tment (206-05 Parki ng Brake and Actuat ion, GeneralProcedures).
Door Locks and Hinges
1. Check operat ion of all door locks, bonnet lock and fuel fi ll er flap.
2. Lubricate al l door check s t raps , bonnet cat ch and fuel fill er fl ap cat ch.
Cooling System
CAUTION: Anti-freeze concentration must be maintained at 50%.
1. Check s peci fi c gravit y of cool ant us ing a hydrometer.
• NOTE: A s uit able hydromet er is avail abl e from the Equipment Programme under Part Number 511 3302 001 00.
2. Top-up cool ing s ys tem if neces s ary.For addit ional informat ion, refer t o: Specificati ons (303-03A Engine Cool ing - I6 3.2L Pet rol , Specificati ons ).
Cooling system - Check/Top-up
W ARNING: Since injury such as scalding could be caused by escaping steam or coolant, do not remove the fillercap from the coolant expansion tank whilst the system is hot.
• CAUTIO NS:
Engine coolant w ill damage the paint finished surfaces. If coolant is spilled, immediately remove the coolantand wash the area with water.
Always top-up with a 50% mixture of anti-freeze and water.
Check t he l evel of cool ant i n t he expans ion t ank. W it h t he engi ne col d, the coolant level must be to the UPPERLEVEL indicat or mark above the COLD FILL RANGE t ext on the s i de of the expans i on tank. Ignore any coolantwhich may be vis ible in t he t op s ect ion of t he t ank.If topping-up i s requi red, remove expans ion tank fill er cap and top-up coolant level to the UPPER LEVEL indicat ormark.For addit ional informat ion, refer t o: Specificati ons (303-03A Engine Cool ing - I6 3.2L Pet rol , Specificati ons ).Ins t all expans ion t ank fi ll er cap, ti ght en cap unti l ratchet is heard to 'cli ck'.
Coolant - Replace
Every 10 years: Repl ace the coolant.For addit ional informat ion, refer t o: Cool ing Sys tem Drai ning, Fi ll ing and Bl eeding (303-03A Engine Cooli ng - I6 3.2L Pet rol,General Procedures ).
Ignition System
Every 75,000 miles (120,000 km). Replace s park plugs .For addit ional informat ion, refer t o: Specificati ons (303-07B Glow Pl ug Sys t em, Specificati ons ).
Accessory Drive Belt
CAUTION: For vehi cl es operati ng under arduous condi ti ons s ee relevant s ecti on.
Check t he condi ti on of the access ory drive bel t.Remove all t races of mud and dirt from t he dri ve belt and pull eys .Check t he drive belt for si gns of s pli tt ing and wear.Every 105,000 miles (168,000 km) - Petrol models: Replace the accessory drive belt. For addi ti onalinformat ion, refer t o: Acces s ory Drive Belt (303-05A Acces s ory Drive - I6 3.2L Pet rol , Removal and Ins t allat ion).

Fluid levels
Brake Fluid Reservoir
Remove the brake fl uid reservoi r cover.Check t he fluid level i n t he brake fluid res ervoir, the l evel mus t be t o t he MAX mark on the reservoi r; t op-up i fneces s ary.Clean t he area around the res ervoi r fi ll er cap, remove cap.If necess ary, t op-up us ing t he recommended fluid to the MAX mark on t he res ervoir.For addit ional informat ion, refer t o: Specificati ons (206-00 Brake Syst em - General Informati on, Speci fi cat ions ).Ins t all the res ervoir fill er cap.Ins t all the brake fl uid reservoi r cover.
Power Steering Fluid Reservoir
CAUTION: T o prevent over filling, check/top-up the system with the engine sw itched off and the system cold.Ensure that the steering wheel is in the straight ahead position, do not turn the steering w heel prior to checking thefluid level.

Check t hat the flui d level is t o t he mi d-way mark between the MAX and MIN marks on t he fluid res ervoir, t op-up i fneces s ary.Clean t he area around the res ervoi r fi ll er cap, remove cap.
CAUTION: Do not fill reservoir above the MAX mark.
If necess ary, t op-up us ing t he recommended fluid to the mid-way mark on the reservoir.For addit ional informat ion, refer t o: Specificati ons (211-02 Power St eering, Specificati ons).Ins t all the res ervoir fill er cap.
Windshield Washer Reservoir
Remove the winds hi eld was her res ervoir fill er cap.Top-up t he res ervoir us ing a mi xt ure of an approved wi nds hiel d was her flui d and water unti l the level i s t o thebott om of t he gauze fil ter i n t he res ervoir fil ler neck.Ins t all the res ervoir fill er cap.
Engine Oil and Filter
CAUTION: For vehi cl es operati ng under arduous condi ti ons s ee relevant s ecti on.
Every 6 months or 7,500 miles (12,000 km): NAS and Gulf markets Renew engi ne oil and filt er.For addit ional informat ion, refer t o: Specificati ons (303-01A Engine - I6 3.2L Petrol, Speci fi cat ions).
Air Filtering
CAUTION: For vehi cl es operati ng under arduous condi ti ons s ee relevant s ecti on.
1. Every 2 years or 30,000 miles (48,000 km): Replace the ai r cl eaner element .For addit ional informat ion, refer t o: Air Cl eaner (303-12A Int ake Ai r Dis t ri but ion and Fi lt ering - I6 3.2L Petrol , Removal andIns t allat ion).
Automatic Transmission
Every 10 years or 150,000 miles (240,000 km): Renew automat ic t rans mis s ion flui d.For addit ional informat ion, refer t o: Specificati ons (307-01 Aut omati c Trans mis s ion/Transaxle, Speci fi cat ions ).
Manual Transmission
Every 10 years or 150,000 miles (240,000 km): Renew manual t rans mi ss ion fl ui d.For addit ional informat ion, refer t o: Specificati ons (308-00 Manual Trans mis s ion/Transaxle and Clutch - GeneralInformat ion, Speci ficat ions).
Power Transfer Unit
Every 10 years or 150,000 miles (240,000 km): Renew power t rans fer unit oi l.For addit ional informat ion, refer t o: Specificati ons (205-03, Speci fi cat ions ).
Differential Assembly - Rear
Every 10 years or 150,000 miles (240,000 km): Renew rear different ial oil .For addit ional informat ion, refer t o: Specificati ons (205-02 Rear Drive Axle/Different ial, Specifi cat ions ).
Suspension and Body Mountings