Lexus CT200h 2017 Owner's Manual (in English)

511
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
7
Maintenance and care
Checking and replacing fuses
Turn the power switch off.
Open the fuse box cover.
Engine compartment
Push the tab in and lift the lid off.
Left side instrument panel
Remove the lid.
If any of the electrical components do not operate, a fuse may have blown. If
this happens, check and replace the fuses as necessary.
1
2

512
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
Remove the fuse.
Only type A fuse can be removed
using the pullout tool.
Check if the fuse is blown.
Normal fuse
Blown fuse
Replace the blown fuse with a new fuse of an appropriate amperage rating. The
amperage rating can be found on the fuse box lid.
3
4
1
2
Ty p e ATy p e B
Ty p e CTy p e D

CT200h_OM_OM76215U_(U)
5137-3. Do-it-yourself maintenance
7
Maintenance and care
■After a fuse is replaced
●If the lights do not turn on even after the fuse has been replaced, a bulb may need
replacement. (P. 5 1 4 )
●If the replaced fuse blows again, have the vehicle inspected by your Lexus dealer.
■If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
■When replacing light bulbs
Lexus recommends that you use genuine Lexus products designed for this vehicle.
Because certain bulbs are connected to circui ts designed to prevent overload, nongenu-
ine parts or parts not designed for this vehicle may be unusable.
WA R N I N G
■To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or injury.
●Never use a fuse of a higher amperage rati ng than that indicated, or use any other
object in place of a fuse.
●Always use a genuine Lexus fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
●Do not modify the fuses or fuse boxes.
■Fuse box near the power control unit
Never check or replace the fu ses as there are high voltage parts and wiring near the
fuse box.
Doing so may cause electric shock, re sulting in death or serious injury.
NOTICE
■Before replacing fuses
Have the cause of electrical overload determ ined and repaired by your Lexus dealer as
soon as possible.

514
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
Light bulbs
Check the wattage of the light bulb to be replaced. (
P. 585)
 P. 4 8 4
■Front
Vehicles with halogen headlights
You may replace the following bulbs by yourself. The difficulty level of replace-
ment varies depending on the bulb. If necessary bulb replacement seems diffi-
cult to perform, contact your Lexus dealer.
For more information about replacing other light bulbs, contact your Lexus
dealer.
Preparing for light bulb replacement
Removing the engine compartment cover
Bulb locations
Front turn signal light
Halogen fog light (if equipped) Headlight low beam
Headlight high beam1
2
3
4

CT200h_OM_OM76215U_(U)
5157-3. Do-it-yourself maintenance
7
Maintenance and care
Vehicles with LED headlightsHeadlight high beam
Front turn signal light
■RearBack-up light
Rear turn signal light
1
2
1
2

516
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
■Headlight low beams (halogen headlights)
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the headlight low
beams on once and visually confirm
that no light is leaking through the
mounting.
Replacing light bulbs
1
2
3
4

CT200h_OM_OM76215U_(U)
5177-3. Do-it-yourself maintenance
7
Maintenance and care
■Headlight high beams (halogen headlights)For the right side only: Move the
washer fluid filler opening.
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
1
2
3
4

518
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the headlight high
beams on once and visually confirm
that no light is leaking through the
mounting.
For the right side only: Reinstall the washer fluid filler opening.
■Headlight high beams (LED headlights)
Turn the cover counterclockwise
and remove it.
Turn the bulb base counterclock-
wise.
Unplug the connector while pull-
ing the lock release.
5
6
1
2
3

CT200h_OM_OM76215U_(U)
5197-3. Do-it-yourself maintenance
7
Maintenance and care
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb with
the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to check
that it is not loose, turn the headlight
high beams on once and visually
confirm that no light is leaking
through the mounting.
When installing the cover, conduct step in reverse.
■Halogen fog light (if equipped)Remove 2 screws, a bolt and clip,
and pull down the fender liner.
Pull the fender liner down slowly,
being careful not to dislodge any
fixed components.
4
5
61
1

520
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn th
e fog lights on once
and visually confirm that no light is
leaking through the mounting.
2
3
4
5