torque LEXUS SC400 1991 Service Repair Manual

37. INSTALL AIR CONDITIONING (A/C) COMPRESSOR
(a) Install the A/C compressor, compressor stay and groundcable with the nut and 3 bolts.
Torque:
49 NVm (500 kgf Vcm, 36 ft Vlbf) for bolt
29 N Vm (300 kgf Vcm, 22 ft Vlbf) for nut
(b) Connect the A/C compressor connector.
38. INSTALL RADIATOR ASSEMBLY
(a) Install the 2 lower radiator supports to the radiator.
(b) Place the radiator assembly on the body bracket.
(c) Slightly lift the radiator, and connect the 2 oil cooler hoses (for
cooling fan) to the hose clamp on the radiator fan shroud.
(d) Install the upper radiator support with the 2 bolts and screw. Install the 2 upper radiator supports.
Torque: 12 N Vm (120 kgf Vcm, 9 ft Vlbf)
EG±70±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

39. INSTALL RADIATOR RESERVOIR TANK
(a) Install the reservoir tank to the reservoir tank bracket.
(b) Install the reservoir tank with the bracket and 3 bolts.
Torque: 4.9 NVm (50 kgf Vcm, 43 in. Vlbf)
(c) Connect the following hoses:
(1) Reservoir hose to water inlet housing
(2) Reservoir hose to radiator
(d) Connect the coolant level sensor connector.
40. INSTALL DRIVE BELT Install the drive belt by turning the drive belt tensioner coun-
terclockwise.
HINT: The pulley bolt for the dive belt tensioner has a left
hand thread.
41. INSTALL BATTERY
42. FILL WITH ENGINE COOLANT
43. START ENGINE AND CHECK FOR LEAKS
44. CHECK TRANSMISSION FLUID LEVEL
45. INSTALL ENGINE UNDER COVER
EG±72
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

D. Inspect camshaft bearingsCheck that bearings for flaking and scoring.
If the bearings are damaged, replace the bearing caps and
cylinder head a set.
E. Inspect camshaft gear spring Using a vernier caliper measure the free distance between
the spring ends.
Free distance:
18.2 ± 18.8 mm (0.712 ± 0.740 in.)
If the free distance is not as specified, replace the gear
spring.
F. Inspect camshaft journal oil clearance
(a) Clean the bearing caps and camshaft journals.
(b) Place the camshafts on the cylinder head.
(c) Lay a strip of Plasti gage across each of the camshaft
journals.
(d) Install the bearing caps. (See step 7 on pages EG±114 to 120)
Torque: 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
NOTICE: Do not turn the camshaft.
(e) Remove the bearing caps.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±103
WhereEverybodyKnowsYourName

CYLINDER HEADS INSTALLATION
EG22V±02
(See Components for Removal and Installation)
1. INSTALL RH EXHAUST MANIFOLD TO RH CYLINDERHEAD
(a) Place a new gasket on the cylinder head with the white painted marks facing the manifold side.
NOTICE: Be careful of the Installation direction.
(b) Install the ex haust manifold with 8 new nuts. Uniformly
tighten the nuts in several passes.
Torque: 44 N Vm (450 kgf Vcm, 33 ft Vlbf)
(c) Install the main heated oxygen sensor.
Torque: 44 N Vm (450 kgf Vcm, 33 ft Vlbf)
(d) Install the heat insulator with the 3 bolts.
2. INSTALL LH EXHAUST MANIFOLD TO LH CYLINDER
HEAD
(a) Place a new gasket on the cylinder head with the white
painted marks facing the manifold side.
NOTICE: Be careful of the installation direction.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±109
WhereEverybodyKnowsYourName

(b) Install the exhaust manifold with 8 new nuts. Uniformlytighten the nuts in several passes.
Torque: 44 N Vm (450 kgf Vcm, 33 ft Vlbf)
(c) Install the main heated oxygen sensor.
Torque: 44 N Vm (450 kgf Vcm, 33 ft Vlbf)
(d) Install the heat insulator with the 3 bolts.
3. INSTALL CYLINDER HEADS
A. Place cylinder head on cylinder block
(a) Place 2 new cylinder head gaskets in position on the cylinder
block.
HINT: On the rear side of the cylinder head gasket are
painted marks to distinguish the LH and RH banks, a white
painted mark for the RH bank and a yellow painted mark for
the LH bank.
NOTICE: Be careful of the installation direction.
(b) Place the 2 cylinder heads in position on the cylinder headgaskets.
EG±110
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

B. Install cylinder head boltsHINT:
wThe cylinder head bolts are tightened in 2 progressive
steps (steps (c) and (e)).
w If any cylinder head bolt is broken or deformed, replace
it.
(a) Apply a light coat of engine oil on the threads and under the
heads of the cylinder head bolts.
(b) Install the plate washer to the cylinder head bolt.
(c) Install and uniformly tig hten the 10 cylinder head bolts on one
side of the cylinder head in several passes in the sequence
shown, then do the other side as shown.
Torque: 39 N Vm (400 kgf Vcm, 29 ft Vlbf)
If any one of the cylinder head bolts does not meet the torque
specification, replace the cylinder head bolt.
NOTICE: Do not drop the plate washer for cylinder head bolt
into portion A of the cylinder head. If dropped into portion A,
the plate washer will pass through the cylinder head and cylin-
der block into the oil pan.
(d) Mark the front of the cylinder head bolt head with paint.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±111
WhereEverybodyKnowsYourName

(d) RH Cylinder Head:Install the bearing cap (mark ª11º) in position with the arrow
mark facing rearward.
(e) LH Cylinder Head: Install the bearing cap (mark ª16º) in position with the arrow
mark facing forward.
(f) Install a new seal washer to the bearing cap bolt.
(g) Apply a light coat of engine oil on the threads of the bearing
cap bolt.
(h) Install the 4 bearing cap bolts. Alternately tighten bearing cap bolts.
Torque: 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
HINT: Use silver colored bolts 38 mm (1.50 in.) in length.
6. ASSEMBLE EXHAUST CAMSHAFT
(a) Install the following parts: (1) Camshaft gear spring
(2) Camshaft sub±gear
(3) Wave washer
HINT: Align the pins on the gears with the spring ends.
(b) Using snap ring pliers, install the snap ring.
(c) Mount the hexagon wrench head portion of the camshaft in a vise.
NOTICE: Be careful not to damage the camshaft.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±113
WhereEverybodyKnowsYourName

(f) Install the other 4 bearing caps in the sequence shown withthe arrow marks facing rearward.
HINT: Align the arrow marks at the front and rear of the cylin-
der head with the mark on the bearing cap.
(g) Apply a light coat of engine oil on the threads and under the heads (A only) of the bearing cap bolts.
HINT: Do not apply engine oil under the heads of the bearing
cap bolt (B).
(h) Install a new seal washer to the bearing cap bolt (B). Install the 8 bearing cap bolts as shown.
HINT:
wUse bearing cap bolts 38 mm (1.50 in.) in length. The
bolts are black (A) or silver (B) in color. Install the 2 silver
bolts to the front bearing cap. Install the 6 black bolts to
the other positions.
w After installing the oil feed pipe, install the 2 bolts to rear
bearing cap as directed in step B (i).
(i) Uniformly tighten the 8 bearing cap bolts in several passes, in the sequence shown.
Torque: 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
B. Install exhaust camshaft to RH cylinder head
(a) Set the timing mark (1 dot mark) of the camshaft drive gear
at 10
angle by turning the hexagon wrench head portion of
the intake camshaft with a wrench.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±115
WhereEverybodyKnowsYourName

(j) Uniformly tighten the 8 bolts on the bearing caps of theexhaust camshaft in several passes, in the sequence shown.
Torque: 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
(k) Alternately tighten the 2 bolts on the rear bearing caps of the
intake camshaft in several passes.
Torque: 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
(l) Boring the service bolt installed in the driven subgear upward
by turning the hexagon wrench head portion of the camshaft
with a wrench.
(m) Remove the service bolt.
C. Install intake camshaft to LH cylinder head
(a) Apply MP grease to the thrust portion of the intake camshaft.
(b) Place the intake camshaft at 60
angle of the timing mark (1
dot mark) on the cylinder head.
(c) Remove any old packing (FIPG) material.
(d) Apply seal packing to the bearing cap (mark ª11º) as shown.
Seal packing: Part No. 08826±00080 or equivalent
±
1UZ±FE ENGINE ENGINE MECHANICALEG±117
WhereEverybodyKnowsYourName

(e) Install the front bearing cap (mark ª11º) with the arrow markfacing forward.
HINT:
wInstalling the front bearing cap will determine the thrust
portion of the camshaft.
w Align the allow marks at the front and rear of the cylinder
head with the mark on the bearing cap.
(f) Install the other 4 bearing caps in the sequence shown with the arrow marks facing rearward.
HINT: Align the arrow marks at the front and rear of the cylin-
der head with the mark on the bearing cap.
(g) Apply a light coat of engine oil on the threads and under the heads (A only) of the bearing cap bolts.
HINT: Do not apply engine oil under the heads of the bearing
cap bolt (B).
(h) Install a new seal washer to the bearing cap bolt (B). Install the 8 bearing cap bolts as shown.
HINT:
wUse bearing cap bolts 38 mm (1.50 in.) in length. The
bolts are black (A) or silver (B) in color. Install the 2 silver
bolts to the front bearing cap. Install the 6 black bolts to
the other positions.
w After installing the oil feed pipe, install the 2 bolts to the
bearing cap 2nd from the front as directed in step B (i).
(i) Uniformly tighten the 8 bearing cap bolts in several passes, in the sequence shown.
Torque: 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
EG±118±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName