length MAZDA 626 1987 Owner's Manual

7B INSPECTION AND REPAIR
OIL PUMP
Disassembly
Disassemble in the sequence shown in the figure.
8—11 Nm (82—112 cm-kg, 71—97 in-lb)
24—35 N-m (2.4-3.6 m-kg, 17-26 ft-lb)
1. Bearing race
2. Seal rings
3. Oil pump cover
4. Pump flange
5. Guide ring and guide spring
6. Vane
7. Rotor
8. Spring
86U07B-174
9. Cam ring
10. Pivot roller
11. Seal pin and spring
12. Spring
13. Valve
14. Oil pump body
15. O-ring
Inspection
Check the following and replace any faulty parts.
1. Sliding surfaces of the oil pump cover and oil pump
body for damage or wear
2. Broken or worn seal ring
3. Weakened spring
Free length of springs:
(1) For the cam ring (No. 8)
41.6 mm (1.64 in)
(2) For the valve (No. 12)
35.0 mm (1.38 in)
86U07B-175
7B—108

7B INSPECTION AND REPAIR
6. Spring and retainer assembly for separation or
deformation
Free length of spring:
29.8 mm (1.173 in)
86U07B-198
Assembly
Reverse clutch
1. Install the reverse piston.
(1) Apply ATF to inner and outer faces of the seals,
and install them to the reverse piston.
(2) Face the outer seal lip toward the inside by
gently rolling
it
down around the circumference
for easier installation into the reverse clutch
drum.
86U07B-199
(3) Install the reverse piston by pushing evenly
around the circumference, being careful not to
damage the seal rings.
86U07B-200
2. Install the piston return spring with the tabs facing
away from the reverse piston.
3. Install the return spring stopper with the step fac-
ing upwards.
86U07B-201
7B—116

INSPECTION AND REPAIR 7B
86U07B-245
SB T
g. SH -i
1
Inspection
Check the following and repair or replace any faulty
parts.
1. Drive and driven plates for damage or wear
Drive plate thickness
Standard: 1.6 mm (0.063 in)
Minimum: 1.4 mm (0.055 in)
2. Clutch piston for damage or cracks
3. Clutch drum for damage or deformation
4. Seal contact areas for damage
5. Check ball for leaking or sticking
6. Spring and retainer assembly for separation or
deformation
7. Broken or worn snap ring
8. Broken or weakened spring
Free length of spring:
33.2 mm (1.307 in)
86U07B-246
Assembly
1. Install the 3-4 clutch piston.
(1) Apply ATF to the inner and outer seals, and
install them onto the 3-4 clutch piston.
(2) Install the piston by pushing evenly around the
circumference, being careful not to damage the
seal rings.
86U07B-247
2. Install the spring and retainer assembly.
86U07B-248
7B—129

7B INSPECTION AND REPAIR
2-3 ACCUMULATOR
Disassembly
Disassemble in the sequence shown in the figure.
1. Snap ring
2. Stopper plug
3. O-ring
4. 2-3 accumulator
spring
5. 2-3 accumulator
piston
6. Large seal ring
7. Small sea ring
86U07B-255
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn piston
2. Damaged or worn stopper plug
3. Broken or weakened spring
Free length of spring:
G4A-EL 83.3 mm (3.280 in)
G4A-HL 76.0 mm (2.992 in)
76G07B-138
Assembly
1. Install the 2-3 accumulator.
(1) Apply ATF to large and small seal rings; then
install them to the accumulator piston.
(2) Insert the 2-3 accumulator.
86U07B-257
7B—132

7B INSPECTION AND REPAIR
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn governor gear
2. Damaged or worn governor valve
3. Cracked or damaged governor carrier and sleeve
83U07B-267
Assembly
1. Insert the governor valve to the governor carrier
and sleeve.
2. Install the governor driven gear.
3. Install the roll pin.
83U07B-268
86U07B-260
LOW AND REVERSE BRAKE
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn drive and driven plates
Drive plate thickness
Standard: 1.6 mm (0.063 in)
Minimum: 1.4 mm (0.055 in)
2. Broken or worn snap ring
3. Deformed or detached spring and retainer as-
sembly
4. Broken or weakened spring
Free length of spring:
20.5 mm (0.807 in)
5. Damaged or worn piston
6. Damaged seal contact area of transaxle case
7B—134 expert22 fl/m http://rutracker.org

INSPECTION AND REPAIR 7B
2-4 BRAKE BAND
Inspection
Check the following and replace if necessary.
1. Damaged or worn 2-4 brake band
86U07B-261
BAND SERVO
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn piston
2. Weakened return spring
Free length of spring:
G4A-EL: 43.25 mm (1.703 in)
G4A-HL: FE engine 42.0 mm (1.654 in)
F8 engine 43.25 mm (1.703 in)
76G07B-140
OTHER INSPECTION
Check the following and replace any faulty parts.
1. Damaged or worn output shell
2. Damaged or worn internal gear
3. Damaged or worn turbine shaft
4. Damaged or worn oil pump shaft
5. Damaged or worn anchor strut and shaft
86U07B-263
6. Damaged or cracked valve body cover
7. Damaged or cracked oil pan
8. Damaged or clogged oil strainer
86U07B-264
7B—135

7B INSPECTION AND REPAIR
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn valves
2. Damaged oil passage
3. Cracked or damaged valve body
4. Operation of each valve
5. Weakened spring
Spring

Spring name Outer dia.
mm
(in) Free length
mm
(in) Wire dia.
mm (in)
Spring color
1-2 accumulator small spring 11.0 (0.433) 88.1 (3.348) 1.4 (0.055) Gray
1-2 accumulator large spring 16.0 (0.630) 78.0 (3.071) 2.0 (0.079) Blue
Bypass, Servo control spring 5.0 (0.197) 33.4 (1.315) 0.55 (0.022) Maroon
2-3 timing spring 8.3 (0.327) 26.5 (1.043) 0.8 (0.031)
—

N-R accumulator rear spring 11.1 (0.437) 62.0 (2.441) 1.2 (0.047) Light green
N-D accumulator front spring 9.8 (0.386) 52.9 (2.083) 1.0 (0.039) Brown
Coasting bypass spring 5.8 (0.228) 37.7 (1.484) 0.6 (0.024) Dark blue
3-2 timing spring 8.2 (0.323) 28.6 (1.126) 0.8 (0.031) Red
3-2 capacity spring 5.4 (0.213) 30.6 (1.205) 0.5 (0.020) White
Throttle relief ball spring 6.6 (0.260) 21.6 (0.850) 0.8 (0.031)
—
76G07B-151
Assembly
1. Install the 3-2 capacity valve, 3-2 capacity spring,
and stopper plug; then install the stopper pin.
2. Install the 3-2 timing valve, the 3-2 timing spring,
and retainer.
86U07B-280
3. Install the coasting bypass plug, coasting bypass
valve and coasting bypass spring.
4. Apply ATF to the O-rings, and install them to the
piston; then insert the N-R accumulator rear spring
and N-R accumulator piston.
5. Apply ATF to the O-rings, and install them to the
piston; then insert the N-D accumulator piston and
N-D accumulator front spring.
76G07B-152
7B—142

INSPECTION AND REPAIR 7B
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn valves
2. Damaged oil passage
3. Cracked or damaged valve body
4. Operation of each valve
5. Weakened spring
Spring

Spring name Outer dia.
mm
(in) Free length
mm (in)
Wire dia.
mm
(in) Spring color
Pressure modifier spring 8.3 (0.327) 26.5 (1.043) 0.8 (0.031)
—

Low reducing spring 8.7 (0.343) 38.3 (1.508) 0.9 (0.035) Black
1-2 shift spring 8.7 (0.343) 41.3 (1.626) 1.0 (0.039) Yellow
2-3, 3-4 shift spring 7.4 (0.291) 36.6 (1.441) 0.8 (0.031) Gray
Throttle backup spring 9.65 (0.380) 26.9 (1.059) 0.55 (0.022) Red
Throttle modulator spring 6.3 (0.248) 47.9 (1.886) 0.8 (0.031)
—

Throttle assist spring 5.15 (0.203) 32.3 (1.272) 0.55 (0.022) Dark green
Throttle spring 5.4 (0.213) 47.2 (1.858) 0.8 (0.031) Pink
Converter relief ball spring 6.9 (0.272) 24.1 (0.949) 0.9 (0.035) Maroon
Orifice check valve spring 5.0 (0.197) 12.5 (0.492) 0.23 (0.009)
—
76G07B-219
]
Assembly
1. Install the throttle adjust plug, throttle assist spring,
throttle valve, and throttle plug assembly.
86U07B-288
Caution
Install the throttle plug assembly with the
groove aligned with the bolt hole.
86U07B-289
7B-145

7B INSPECTION AND REPAIR
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn valves
2. Damaged oil passage
3. Cracked or damaged valve body
4. Operation of each valve
5. Weakened spring
Spring

Spring name Outer dia.
mm
(in) Free length
mm
(in) Wire dia.
mm (in)
Spring color
Pressure regulator spring 11.5 (0.453) 26.5 (1.043) 1.0 (0.039) Maroon
Lock-up control spring 5.0 (0.197) 35.2 (1.386) 0.6 (0.024) Purple

86U07B-295
Assembly
1. Install the lock-up control spring, lock-up control
valve, stopper plug, and stopper pin.
86U07B-296
Install the pressure regulator valve, pressure regu-
lator spring, pressure regulator spring seat, pres-
sure regulator plug, pressure regulator plug sleeve,
pressure regulator backup plug, stopper plug, and
stopper pin.
Note
Install the stopper plug larger end first.
86U07B-297
3. Install the manual valve.
86U07B-298
7B-148

INSPECTION AND REPAIR 7B
Inspection
Check the following and replace any faulty parts.
1. Damaged or worn valves
2. Damaged oil passage
3. Cracked or damaged valve body
4. Operation of each valve
5. Weakened spring
Spring

Spring name Outer dia.
mm
(in) Free length
mm (in)
Wire dia.
mm
(in) Spring color
1-2 accumulator small spring F8 engine 9.9 (0.400) 84.7 (3.335) 1.2 (0.047) Red
1-2 accumulator large spring
FE engine 13.0 (0.512) 73.2 (2.881) 1.8 (0.071) Pink 1-2 accumulator large spring F8 engine 16.0 (0.630) 84.7 (3.335) 2.0 (0.079) White
Bypass spring 5.0 (0.197) 25.1 (0.988) 0.7 (0.028) Yellow
Servo control spring 4.9 (0.193) 27.1 (1.067) 0.5 (0.020) Light blue
2-3 timing spring 8.3 (0.327) 26.5 (1.043) 0.8 (0.031)
—

N-R accumulator rear spring 11.1 (0.437) 68.2 (2.685) 1.0 (0.039) Blue
N-D accumulator front spring 9.8 (0.386) 60.9 (2.398) 1.1 (0.043) Yellow
Low reducing spring 8.7 (0.343) 38.3 (1.508) 0.9 (0.035) Black
OD release spring 6.0 (0.236) 32.6 (1.283) 0.6 (0.024) Orange
Coasting bypass spring 5.8 (0.228) 31.3 (1.232) 0.6 (0.024) Yellow
3-2 timing spring 8.2 (0.323) 28.55 (1.124) 0.8 (0.031) Maroon
3-2 capacity spring 5.55 (0.219) 30.5 (1.201) 0.55 (0.022) Light green
Throttle relief ball spring 6.6 (0.260) 20.3 (0.799) 0.8 (0.031) Light green

76G07B-165
Assembly
1. Install the 3-2 capacity valve, 3-2 capacity spring,
stopper plug, and stopper pin.
2. Install the 3-2 timing valve, 3-2 timing spring, and
retainer.
83U07B-287
3. Install the coasting bypass plug, coasting bypass
valve, and coasting bypass spring.
4. Apply ATF to the O-rings, and install them onto the
piston; then insert the N-R accumulator rear spring,
and N-R accumulator piston.
5. Apply ATF to the O-rings, and install them onto the
piston; then insert the N-D accumulator piston, and
N-D accumulator front spring.
83U07B-288
7B—161