MAZDA MODEL 6 2008 Owners Manual (in English)
Manufacturer: MAZDA, Model Year: 2008, Model line: MODEL 6, Model: MAZDA MODEL 6 2008Pages: 440, PDF Size: 6.49 MB
Page 91 of 440

Black plate (91,1)
2. Set the right side of the retainer baronto the retainer loop on the right side
of the luggage compartment.
Retainer
loop
3. Slowly pull out the cover towards youand insert the cover ends into the hook
retainers at the rear of the vehicle.
Hook
retainer
Removing the cover
1. Remove the cover ends from the hookretainers and slowly roll up the cover. NOTE
To fully retract and protect the cover, guide the
cover all the way into the retainer.
Ta b
2. Press and hold the button on the right
side of the retainer bar and lift the bar.
Button
3. Remove the left end of the retainer barfrom the notch.
qLuggage Compartment Net
The luggage compartment net can be used
as a compartment separator or to keep
animals in the back.
CAUTION
Make sure the net is firmly secured. If
it is not firmly secured, it could
unexpectedly disengage resulting in
injury.
Knowing Your Mazda
Doors and Locks
3-15
Mazda6_8X47-EA-07G_Edition1 Page91
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 92 of 440

Black plate (92,1)
NOTEThe width of the net anchors can be shortened
by pushing both sides inward.
Net anchor
Dividing the luggage compartmentfrom the rear seat
WARNING
Do not use the luggage compartment
net to secure objects in the luggage
compartment or the rear seat area:Using the luggage compartment net
to secure objects in the luggage
compartment or the rear seat area is
dangerous. The luggage
compartment net is not designed to
hold objects in place that could fly
forward in a frontal collision.
Unsecured objects that are thrown
around the inside of the vehicle could
cause injury to occupants. This is
particularly true for objects stacked
above the seatback level. Never stack
objects above the seatback level. If
the luggage compartment is divided
from the rear seat, pull the luggage
compartment cover over the cargo in
the luggage compartment.
Make sure luggage and cargo is
secured before driving: Not securing cargo while driving is
dangerous as it could move or be
crushed during sudden braking or a
collision and cause injury.
To install the net:
1. Install the retainer bar in the luggage compartment.
3-16
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page92
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 93 of 440

Black plate (93,1)
2. Slowly pull out the net in the upwarddirection, insert the left and right net
anchors into the ceiling retainers, and
slide them to the position indicated in
the figure.
Net
anchor
Net
To remove the net:
1. Lift the net slightly and disengage the
anchors from the ceiling retainers.
2. Slowly lower and support the net as it rolls up into the retainer bar.
CAUTION
When disengaging the net anchors,
hold the top of the net firmly in your
hand. If you lose control of the net, it
will automatically roll up in an
uncontrolled manner and could
cause injury.
Dividing the luggage compartmentfrom the front seats
WARNING
Do not use the luggage compartment
net to secure objects in the luggage
compartment or the rear seat area: Using the luggage compartment net
to secure objects in the luggage
compartment or the rear seat area is
dangerous. The luggage
compartment net is not designed to
hold objects in place that could fly
forward in a frontal collision.
Unsecured objects that are thrown
around the inside of the vehicle could
cause injury to occupants. This is
particularly true for objects stacked
above the seatback level. Never stack
objects above the seatback level. If
the luggage compartment is divided
from the rear seat, pull the luggage
compartment cover over the cargo in
the luggage compartment.
Make sure luggage and cargo is
secured before driving: Not securing cargo while driving is
dangerous as it could move or be
crushed during sudden braking or a
collision and cause injury.
CAUTION
Moving the rear seatbacks with the
retainer bar mounted could scratch
the interior of the vehicle. The
retainer bar must be removed from
the back of the seatbacks before
raising the seatbacks.
To install the net:
1. Fold down the rear seatback (page 2-11).
Knowing Your Mazda
Doors and Locks
3-17
Mazda6_8X47-EA-07G_Edition1 Page93
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 94 of 440

Black plate (94,1)
2. Remove the retainer bar from the rearseatback position.
3. Insert the retainer bar anchors into the left side of each rear seatback retainer
(back of the seatback).
Retainer bar
Rear seat Retainer
4. Slide the retainer bar in the directionindicated in the figure, and engage the
anchors into the seatback retainers.
Retainer bar
5. Slowly pull out the net in the upwarddirection, insert the left and right net
anchors into the ceiling retainers, and
slide them to the position indicated in
the figure.
Net
anchor
Net
To remove the net:
1. Lift the net slightly and disengage thenet anchors from the ceiling retainers.
2. Slowly lower and support the net as it rolls up into the retainer bar.
3. Remove the retainer bar in the reverse order of installation.
CAUTION
When disengaging the net anchors,
hold the top of the net firmly in your
hand. If you lose control of the net, it
will automatically roll up in an
uncontrolled manner and could
cause injury.
3-18
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page94
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 95 of 440

Black plate (95,1)
Trunk Lid (Sedan)
WARNING
Never allow a person to ride in the
trunk:Allowing a person to ride in the trunk
is dangerous. In addition, the person
in the trunk could be seriously
injured or killed during sudden
braking or a collision.
Keep the trunk closed when driving: Exhaust gas entering the cabin of a
vehicle through an open trunk is
dangerous. This gas contains CO
(carbon monoxide), which is
colorless, odorless, and highly
poisonous. If inhaled, it can cause
loss of consciousness and death.
qOpening and Closing the Trunk Lid
WARNING
Close the trunk lid, lock the rear
seatbacks and do not allow children to
play inside the vehicle:Leaving the trunk lid open or leaving
children in the vehicle with the keys is
dangerous. Children could open the
trunk lid and climb inside resulting in
possible injury or death from heat
exposure.
Always keep the car from being a
tempting place to play by locking rear
seats, doors and the trunk, and
keeping the keys where children can
not play with them: Leaving children or animals
unattended in a parked vehicle is
dangerous. Babies left sleeping and
children who lock themselves in cars
or trunks can die very quickly from
heat prostration. Do not leave your
children or pets alone in a car at any
time. Do not leave the car, the rear
folding seats or the trunk unlocked.
CAUTION
For vehicles equipped with a rear
spoiler, do not lift the trunk lid by the
spoiler. Lifting up the trunk lid by the
rear spoiler could cause damage to
the rear spoiler and the trunk lid.
Knowing Your Mazda
Doors and Locks
3-19
Mazda6_8X47-EA-07G_Edition1 Page95
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 96 of 440

Black plate (96,1)
Opening the trunk lid with the key
Insert the key into the slot and turn it
clockwise.
Open
Opening the trunk lid with thetransmitter
The trunk lid can be opened by operating
the keyless entry system transmitter, refer
to Keyless Entry System (page 3-3).
Opening the trunk lid with the remoterelease button
Push the release button.
Closing the trunk lid
Use both hands to push the trunk lid down
until the lock snaps shut. Do not slam it.
Pull up on the trunk lid to make sure it is
secure.
qTrunk Light
The trunk light is on when the lid is open
and off when it's closed.
NOTETo prevent the battery from being discharged,
do not leave the trunk open for a long period
when the engine is not running.
3-20
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page96
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 97 of 440

Black plate (97,1)
Inside Trunk Release
Lever (Sedan)
Your vehicle is equipped with an inside
trunk release handle that provides a means
of escape for children and adults in the
event they become locked inside the
trunk.
No matter how careful adults might be
with keys and locking their cars, parents
should be aware that children may be
tempted to play around vehicles and use
the trunk as a hiding place.
Adults are advised to familiarize
themselves with the operation and
location of the inside release handle so
that all children can be told about it in an
appropriate way, keeping in mind that
most vehicles don't have such handles.
WARNING
Close the trunk lid, lock the rear
seatbacks and do not allow children to
play inside the vehicle:Leaving the trunk lid open or leaving
children in the vehicle with the keys is
dangerous. Children could open the
trunk lid and climb inside resulting in
possible injury or death from heat
exposure.
Always keep the car from being a
tempting place to play by locking rear
seats, doors and the trunk, and
keeping the keys where children can
not play with them: Leaving children or animals
unattended in a parked vehicle is
dangerous. Babies left sleeping and
children who lock themselves in cars
or trunks can die very quickly from
heat prostration. Do not leave your
children or pets alone in a car at any
time. Do not leave the car, the rear
folding seats or the trunk unlocked.
Knowing Your Mazda
Doors and Locks
3-21
Mazda6_8X47-EA-07G_Edition1 Page97
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 98 of 440

Black plate (98,1)
qOpening the Trunk Lid from the
Inside
Slide the inside trunk release lever in the
direction of the arrow. The lever is made
of material that will glow for hours in the
darkness of the trunk following a brief
exposure to ambient light.
The inside trunk release lever is located
on the inside of the trunk lid.
Power Windows
The ignition switch must be in the ON
position for the power windows to
operate.
WARNING
Make sure the opening is clear before
closing a window:
Closing power windows are
dangerous. A person's hands, head,
or even neck could be caught by the
window and result in serious injury
or even death.
This warning applies especially to
children.
Always lock all passenger power
windows with the power window lock
switch on the driver's side while
children are in the vehicle, and never
allow children to play with power
window switches: Leaving the power window switches
unlocked while children are in the
vehicle is dangerous. Power window
switches that are not locked with the
power window lock switch would
allow children to operate power
windows unintentionally which could
result in serious injury if a child's
hands, head or neck becomes caught
by the window.
CAUTION
To prevent burning out the fuse and
damaging the power window system,
do not open or close more than three
windows at once.
3-22
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page98
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 99 of 440

Black plate (99,1)
qOperating the Front Power Windows
NOTElEach passenger power window can be
operated with each door switch when the
power window lock switch on the driver's
door is in the unlocked position (page
3-26).
lEach passenger power window can also be
operated by the power window master
control switches on the driver's door.
Master control switchesDriver's window
Left rear window
Front passenger's
window
Right rear window
lThe following functions can be performed
for the front power windows using the
power window master control switches on
the driver's door or front passenger's door
switch.
lManual opening/closinglAuto-opening/closinglTwo-step down function
Manual opening/closing
To open a power window to the desired
position, lightly hold down the switch.
To close the power window to the desired
position, lightly pull up the switch.
Open
Close
Master control switches
Driver's
window
Front passenger's
window
Open
Close
Front passenger switch
Auto-opening/closing
To fully open a power window
automatically, press the switch completely
down.
To fully close the power window
automatically, pull the switch completely
up.
To stop the power window partway, pull
or press the switch in the opposite
direction and then release it.
Knowing Your Mazda
Doors and Locks
3-23
Mazda6_8X47-EA-07G_Edition1 Page99
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 100 of 440

Black plate (100,1)
NOTE(POWER WINDOW INITIALIZATION
PROCEDURE)
If the battery was disconnected during vehicle
maintenance, or for other reasons such as a
switch continues to be operated after the
window is fully open/close, the power windows
will not fully open and close automatically. Re-
initialization of the automatic function can be
performed using the master control switches
and the front passenger door switch. Carry out
the following procedure to resume operation:
1. Turn the ignition switch to the ON position.
2. Make sure that the power window lockswitch located on the driver's door is not
depressed.
3. Press the switch and fully open the power window.
4. Pull up the switch to fully close the power window and continue holding the switch for
about 2 seconds after the window fully
closed.
5. Repeat Steps 3-4 for each front power window.
6. Make sure that the power windows operate correctly using the door switches.
Two-step down function
With the power window completely
closed, press the switch lightly and it will
open and stop about 3 cm (1 in) from the
top.
If you continue to press and hold the
switch, the window will resume opening
all the way.
NOTE
Pressing the power window switch once when
the window is fully closed will only open it
about 3 cm (1 in) to allow convenient
ventilation of the cabin.
Canceling the two-step down function
To cancel the two-step down function for
the front power windows, carry out the
following procedure using the master
control switches.
1. Turn the ignition switch to the ONposition and complete the following
procedure within 5 seconds:
Press the power window switch 2 times
firmly, then pull it 2 times firmly.
Master control switches
Driver's
window
Front passenger's
window
2. Turn the ignition switch to the LOCKposition.
3. With the ignition switch in the LOCK position, and within 40 seconds, turn
the ignition switch to the ON position
and complete the following procedure
within 5 seconds:
Press the power window switch 2 times
firmly, then pull 2 times firmly.
3-24
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page100
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G