instrument cluster MAZDA MODEL CX-5 2017 (in English) Repair Manual

4–172
When Driving
Tire Pressure Monitoring System
*Some models.
Tire Pressure Monitoring System *
The Tire Pressure Monitoring System (TPMS) monitors the pressure for each tire.
If tire pressure is too low in one or more tires, the system will inform\
the driver via the
warning light in the instrument cluster and by the warning beep sound.
Refer to Warning Indication/Warning Lights on page 4-33 .
Refer to Tire Infl ation Pressure Warning Beep on page 7-42 .

The tire pressure sensors installed on each wheel send tire pressure dat\
a by radio signal to
the receiver unit in the vehicle.

Tire pressure sensors
NOTE
When the ambient temperature is low due to seasonal changes, tire temperatures are also
lower. When the tire temperature decreases, the air pressure decreases as well. The TPMS
warning light may illuminate more frequently. Visually inspect the tires daily before driving,
and check tire pressures monthly with a tire pressure gauge. When checking tire pressures,
use of a digital tire pressure gauge is recommended.


TPMS does not alleviate your need to check the pressure and condition of\
all four tires
regularly.
CX-5_8FN1-EA-16L_Edition1.indb 1722016/12/12 10:06:19

5–12
Interior Features
Climate Control System
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
  When the DUAL switch is off: Turn the driver temperature control dial
to control the temperature throughout
the entire cabin.
  When the DUAL switch is on: Turn the driver or front passenger
temperature control dial to
independently control the temperature
on each side of the cabin.

NOTE
  The climate control system changes to
the individual operation mode ( DUAL
switch indicator light illuminated) by
turning the front passenger temperature
control dial even when the DUAL switch
is off, which allows individual control
of the set temperature for the driver and
front passenger.
  The temperature units for the
temperature setting display can be
changed in conjunction with the
temperature units for the outside
temperature display.
 (Type A instrument cluster) Refer to Outside Temperature Display on page 4-24 .
 (Type B instrument cluster) Refer to Outside Temperature Display on page 4-17 .

Fan control switch
The fan has seven speeds. The selected
speed will be displayed.
Mode selector switch
The desired air fl ow mode can be selected
(page 5-6 ).
NOTE
   With the air fl ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and air
at a comparably lower temperature will
fl ow through the central, left and right
vents.
   To set the air vent to , press the
windshield defroster switch.
   In the or position, the air
conditioner is automatically turned on
and the outside air position is
automatically selected to defrost the
windshield. In the
or position, the
outside air position cannot be changed
to the recirculated air position.

A/C switch
Pressing the A/C switch while the AUTO
switch is turned on will turn off the air-
conditioning (cooling/dehumidifying
functions).
The on/off of the air-conditioning switches
each time the A/C switch is pressed.
NOTE
   The air conditioner operates when the
A/C switch is pressed while the air
conditioner is turned off.
  The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).

CX-5_8FN1-EA-16L_Edition1.indb 122016/12/12 10:06:25

6–4
Maintenance and Care
Scheduled Maintenance
Scheduled Maintenance (U.S.A., Canada, and Puerto Rico)
Follow Schedule 1 if the vehicle is operated mainly where none of the fo\
llowing conditions
(severe driving conditions)apply.
  Repeated short-distance driving  Driving in dusty conditions  Driving with extended use of brakes  Driving in areas where salt or other corrosive materials are used  Driving on rough or muddy roads  Extended periods of idling or low-speed operation  Driving for long periods in cold temperatures or extremely humid climate\
s  Driving in extremely hot conditions  Driving in mountainous conditions continually
If any do apply, follow Schedule 2. (Canada residents follow Schedule 2.)
Vehicles using Engine Oil Flexible Maintenance
Engine Oil Flexible Maintenance is selected by default for U.S.A. and Pu\
erto Rico residents.
If any following conditions do apply, follow Schedule 2 with engine oil fi xed maintenance.
   Extended periods of idling or low-speed operation such as police car, taxi or driving
school car
   Driving in dusty conditions
The vehicle calculates the remaining oil life based on engine operating \
conditions. The
vehicle lets you know when an oil change is due by illuminating the wren\
ch indicator light
in the instrument cluster. Change the oil as soon as possible within the next 1000 km
(600 mile) or 15 days. Refer page 6-16 for the details.
NOTE
  Please ensure that the Flexible Oil Maintenance Setting is reset after each Oil and Filter
replacement.
  For maintenance guidelines beyond the miles/months listed, follow the ma\
intenance
intervals provided in the Scheduled Maintenance Tables.

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:07:05

6–16
Maintenance and Care
Scheduled Maintenance
Maintenance Monitor
Maintenance Monitor (Type A)
Based on the engine operating conditions, the onboard computer in your v\
ehicle calculates
the remaining oil life in the United States and Puerto Rico. The wrench indicator light in the
instrument cluster will be illuminated when remaining oil life becomes l\
ess than 1,000 km
(600 mile), or remaining days are less than 15 (whichever comes fi rst).
The system must be reset whenever replacing the engine oil.
Reset method
Press and hold the dashboard illumination knob with the ignition switche\
d off, then switch
it on. Keep pressing the dashboard illumination knob for more than 5 sec\
onds. The master
warning light will fl ash for a few seconds when the reset is completed.

Dashboard illumination knob

Maintenance Monitor (Type B)
1. Select the icon on the home screen to display the “Applications” screen.
2. Select “Vehicle Status Monitor”.
3. Select “Maintenance” to display the maintenance list screen.
4. Switch the tab and select the setting item you want to change.

CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:07:06

6–17
Maintenance and Care
Scheduled Maintenance
You can customize settings in the setup display as follows:
Tab Item Explanation
Scheduled Setting
Notifi cation can be switched on/off.
Time (months) Displays the time or distance until maintenance is due.
Select this item to set the maintenance period.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining distance is less than
1,000 km or 600 mile, or the remaining number of days is less than
15 (whichever comes
fi rst).
Distance (km or mile)
Reset Resets the time and distance to the initial values.
Once the system turns on, it needs to be reset whenever carrying
out maintenance.
Tire Rotation Setting
Notifi cation can be switched on/off.
Distance (km or mile) Displays the distance until tire rotation is due.
Select this item to set the tire rotation distance.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining distance is less than 1,000 km
or 600 mile.
Reset Resets the remaining distance to the initial value.
Once the system turns on, it needs to be reset whenever rotating
the tires.
Oil Change Setting Interval
Oil replacement period can be selected from the
fl exible setting or
fi xed setting, or it can be set to non-display.
The fl exible setting is available only in the United States and
Puerto Rico. Once engine oil fl exible maintenance is selected,
the vehicle calculates the remaining oil life based on the engine
operating conditions. The vehicle lets you know when an oil
change is due by illuminating the wrench indicator light in the
instrument cluster. Mazda Genuine 0W-20 oil and Castrol
® 0W-20
oil are required to achieve optimum performance.
Distance (km or mile)
(Displays only in fi xed
setting) Displays the distance until the oil replacement is due.
Select this item to set the oil replacement distance.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining distance is less than 1,000 km
or 600 mile.
Oil life (km or mile)
(Displays only in fl exible
setting) Displays the engine oil life until the oil replacement is due.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining oil life distance is less than
1,000 km or 600 mile.
Reset In
fl exible setting: Resets the remaining oil life to 100 %.
In fi xed setting: Resets the remaining distance to the initial value.
Once the Flexible Oil Maintenance Setting is selected, the system
must be reset whenever replacing the engine oil.

CX-5_8FN1-EA-16L_Edition1.indb 172016/12/12 10:07:06

6–37
Maintenance and Care
Owner Maintenance
The following conditions indicate that the
battery power is low:
  The KEY indicator light (green) fl ashes
in the instrument cluster for about
30 seconds after the engine is turned off
(for vehicles with a type A instrument
cluster (page 4-32 ), messages are
displayed in the instrument cluster).
   The system does not operate and
the operation indicator light on the
transmitter does not fl ash when the
buttons are pressed.
   The system's operational range is
reduced.

Replacing the battery at an Authorized
Mazda Dealer is recommended to prevent
damage to the key. If replacing the battery
by yourself, follow the instruction.
Replacing the key battery
1. Press the knob and pull out the auxiliary key.

Knob
2. Twist a tape-wrapped
fl athead
screwdriver in the direction of the
arrow and open the cover slightly.

Cover

3. Insert the tape-wrapped fl athead
screwdriver into the gap and slide it in
the direction of the arrow.

Cover
Gap

4. Twist the fl athead screwdriver in the
direction of the arrow and remove the
cover.

Cover

CX-5_8FN1-EA-16L_Edition1.indb 372016/12/12 10:07:12

6–53
Maintenance and Care
Owner Maintenance
*Some models.
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
14 FAN GE 30 A Cooling fan
15 ENG.MAIN 40 A Engine control system
16 ABS/DSC M 50 A ABS, Dynamic stability control system
17 FAN DE 40 A —
18 WIPER 20 A Front window wiper and washer
19 HEATER 40 A Air conditioner
20 ADD FAN GE 30 A Cooling fan
21 ENGINE.IG1 7.5 A Engine control system
22 C/U IG1 15 A For protection of various circuits
23 AUDIO2 7.5 A Audio system
24 METER2 7.5 A —
25 ENGINE3 15 A Engine control system
26 ENGINE2 15 A Engine control system
27 ENGINE1 15 A Engine control system
28 AT 15 A Transaxle control system
* , Ignition switch
29 H/CLEAN 20 A —
30 A/C 7.5 A Air conditioner
31 AT PUMP 15 A Transaxle control system
*
32 HORN 15 A Horn
33 R.WIPER 15 A Rear window wiper
34 H/L HI 20 A Headlight high beam
35 ST.HEATER 15 A Heated steering wheel
*
36 FOG 15 A Fog lights *
37
7.5 A Engine control system
38 H/L LOW L 15 A Headlight low beam (LH)
39 ENGINE4 15 A —
40 — — —
41 METER1 10 A Instrument cluster
42 SRS1 7.5 A Air bag
43 BOSE 25 A Bose
® Sound System-equipped model *
44 AUDIO1 15 A Audio system
45 ABS/DSC S 30 A ABS, Dynamic stability control system
46 FUEL PUMP 15 A Fuel system
47 FUEL WARM 25 A —
48 TAIL 15 A Taillights, License plate lights
49 SCR2
FUEL PUMP2 25 A
—
50 HAZARD 25 A Hazard warning
fl ashers, Turn signal lights/Front side-marker
lights, Parking lights
CX-5_8FN1-EA-16L_Edition1.indb 532016/12/12 10:07:16

7–2
If Trouble Arises
Parking in an Emergency
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.


The hazard warning lights warn other
drivers that your vehicle is a traf fi c hazard
and that they must take extreme caution
when near it.



Depress the hazard warning fl asher and
all the turn signals will fl ash. The hazard
warning indicator lights in the instrument
cluster fl ash simultaneously.
NOTE
  The turn signals do not work when the
hazard warning lights are on.
  Check local regulations about the use of
hazard warning lights while the vehicle
is being towed to verify that it is not in
violation of the law.

CX-5_8FN1-EA-16L_Edition1.indb 22016/12/12 10:07:18

7–26
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Contact Authorized Mazda Dealer and Have Vehicle Inspected
If any of the following warning lights or the indicator light turns on/fl ashes, the system may
have a malfunction. Contact an Authorized Mazda Dealer to have your vehicle inspected.

Signal Warning


ABS Warning Light If the ABS warning light stays on while you're driving, the ABS control unit has detected a
system malfunction. If this occurs, your brakes will function normally a\
s if the vehicle had
no ABS.
Should this happen, consult an Authorized Mazda Dealer as soon as possible. NOTE

When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it is the result of the weak battery and does
not indicate an ABS malfunction.
Recharge the battery.
 The brake assist system does not operate while the ABS warning light is illuminated.


Master Warning
Indication/Warning Light
*
With Multi-information Display
Displays when notifi cation of the system malfunctions is required.
Check the message indicated in the display and consult an Authorized Mazda Dealer.

Master
warning
light

Indication in display and master warning light in instrument cluster are\
illuminated at same
time.
This indicates a malfunction with the vehicle system. Check the message \
indicated in the
display and consult an Authorized Mazda Dealer.
For details, refer to the explanations for the warning/indicator lights,\
in the warning/
indicator lights section, which match the symbol in the upper part of th\
e display.
If a message is not indicated in the display, operate the INFO switch to display the
“Warning” screen.
Refer to Message Indicated in Multi-information Display and INFO Switch \
on page 4-20 .
Without Multi-information Display
The light illuminates continuously if any one of the following occurs. C\
onsult an
Authorized Mazda Dealer.
 There is a malfunction in the battery management system.
 There is a malfunction in the brake switch.

Electric Parking Brake (EPB)
Warning Indication/ Warning Light The warning light illuminates when the system has a malfunction. Have yo\
ur vehicle
inspected at an Authorized Mazda Dealer.
CX-5_8FN1-EA-16L_Edition1.indb 262016/12/12 10:07:25

7–30
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning


Blind Spot
Monitoring (BSM) OFF Indicator Light
* A problem in the system may be indicated under the following conditions.
Have your vehicle inspected at an Authorized Mazda Dealer.
 The light does not turn on when the ignition is switched ON.
 The light remains on even when the Blind Spot Monitoring (BSM) system \
can be operated.
 It turns on while driving the vehicle.
NOTE
If the vehicle is driven on a road with less traf fi c and few vehicles that the radar sensors
can detect, the system may pause (The Blind Spot Monitoring (BSM) OFF\
indicator light in
the instrument cluster illuminates). However, it does not indicate a malfunction.


(Amber)
Mazda Radar
Cruise Control with Stop & Go function (MRCC with Stop & Go function)
Warning Indication
* The message is displayed when the system has a malfunction. Have your ve\
hicle inspected
at an Authorized Mazda Dealer.


(Amber)
Lane-keep Assist System (LAS) & Lane Departure
Warning System
(LDWS) Warning Indication
* The message is displayed when the system has a malfunction. Have your ve\
hicle inspected
at an Authorized Mazda Dealer.
The system does not operate when the warning message is displayed.
CAUTION

Always use tires for all wheels that are of the specifi ed size, and the same manufacture,
brand, and tread pattern. In addition, do not use tires with signifi cantly diff erent wear
patterns on the same vehicle. If such improper tires are used, the system may not operate
normally.
 When an emergency spare tire is used, the system may not operate normally.


LED Headlight Warning Light This light illuminates if there is a malfunction in the LED headlight. H\
ave your vehicle
inspected by an Authorized Mazda Dealer.

CX-5_8FN1-EA-16L_Edition1.indb 302016/12/12 10:07:26