light MAZDA MODEL CX-5 2017 Smart Start Guide (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL CX-5, Model: MAZDA MODEL CX-5 2017Pages: 58, PDF Size: 4.81 MB
Page 23 of 58
m{zd{ cx-5 22
ACTIVE DRIVING DISPLAY
(IF EQUIPPED)
ACTIVE DRIVING DISPLAY
To change the settings/adjustments for the Active Driving Display: 1 Select the Settings icon on the Home screen.
2 Select the AD-Disp tab.
3 Select the desired item to change.
HEIGHT: Adjust the position of the virtual image of the Active Driving Display up or down.
BRIGHTNESS CONTROL: Method for adjusting
screen brightness (automatically with instrument
cluster illumination or manually).
BRIGHTNESS: Brightness adjustment (when selecting manual adjustment).
ROTATION
NAVIGATION: On/Off.
DISPLAY INFORMATION
ACTIVE DRIVING DISPLAY
RESET: Reset to default settings.
NOTE:
• If the display does not operate, switch the ignition
off and then switch it back on. If it still does not
operate even with the ignition switched ON,
have the vehicle inspected at an Authorized
Mazda Dealer.
• It may be difficult to view the display when
wearing sunglasses. Take off your sunglasses or
adjust the luminosity.
•
If the battery has been removed and re-installed
or the battery voltage is low, the adjusted position may deviate.
•
The display may be difficult to view or be temporarily affected by weather conditions
such as rain, snow, light, and temperature.
Vehicle Speed Setting using cruise control
Navigation Turn-By-Turn(TBT) direction, distance
and lane guidance
Traffic Sign Recognition (TSR) using navigation
55Speed Limit
IF EQUIPPED
Lane Departure Warning
System (LDWS) operation conditions and warnings
Smart Brake Support (SBS) warnings
Vehicle Speed Setting using cruise control
2364256 17a CX-5 SSG 030117.indd 223/1/17 5:51 PM
Page 26 of 58
25 MAZDAUSA.COM
MAZDA RADAR CRUISE CONTROL (MRCC)
WITH STOP & GO FUNCTION
The MRCC with Stop & Go function maintains vehicle speed and
following distance using a radar sensor to detect a vehicle ahead.
The driver simply presets the vehicle speed between 0 mph and 90 mph and the system will maintain a safe following distance
without having to turn the cruise control off or use the accelerator
or brake pedals. If the vehicle ahead stops while you are following behind it, your vehicle will stop automatically.
The system operates in two modes: CONSTANT SPEED MODE: When no
vehicle is detected ahead, the driver’s set
speed is maintained.
HEADWAY CONTROL MODE: When a vehicle is detected ahead, a distance between your
vehicle and the vehicle ahead is maintained.
Setting the MRCC with Stop & Go function: When the Mode switch is pushed, the vehicle speed and the distance between vehicles while in headway control can be set. The MRCC
with Stop & Go function indication is shown in the multi-information
display. The indicator light in the multi-information display will be
green and will turn on simultaneously.
NOTE: The radar for the MRCC with Stop & Go function is located behind the Mazda
emblem in the grille. Keep this area clean to ensure the system works properly.
How to set the speed:
1 Adjust the vehicle to the desired speed using the accelerator pedal.
2 Push the SET + or SET – switch. The set speed and the inter-vehicle distance display filled
with white lines are displayed in the multi-information display
and the MRCC indicator light
(green) turns on simultaneously.
3
Push the center of the RESUME switch to resume set speed.
Vehicle ahead
MRCC Distance
between vehicle
MRCC Set
vehicle speed
MAZDA RADAR CRUISE CONTROL
WITH STOP & GO FUNCTION (IF EQUIPPED)
MODE DISPLAY
Constant Speed
Headway Control
WARNING:
Switch the MRCC
system off when it is not in use.
DO NOT get out
of the vehicle while the stop hold control
is operating.
WARNING:
Do not rely
completely on the MRCC with Stop
& Go function and always drive
carefully obeying the speed limit.
2364256 17a CX-5 SSG 030117.indd 253/1/17 5:51 PM
Page 27 of 58
m{zd{ cx-5 26
How to set the distance between vehicles:
The distance between vehicles is increased by pushing the
switch and decreased by pushing the switch. The
distance between vehicles can be set to four levels.
Switching to conventional cruise control function: When the Mode switch is pushed while the MRCC with Stop
& Go function system is turned on, the system is switched to conventional cruise control function.
The MRCC with Stop & Go function indicator light (green) in the instrument cluster turns off and “Radar Cruise Control
deactivated” message is displayed in the multi-information
display at the same time.
CLOSE PROXIMITY WARNING While traveling in headway control, if your
vehicle rapidly closes in on a vehicle ahead because the other driver applied his or her
brakes suddenly, a warning sound activates and the BRAKE! warning is indicated in the
display. Always verify the safety of the surrounding area and depress the brake pedal while keeping a safe distance from the vehicle ahead. Additionally, always keep a safe distance
from the vehicles behind you.
NOTE: The MRCC with Stop & Go function sometimes will brake your vehicle when
encountering a semi truck (tractor trailer). This is normal. Simply push the accelerator pedal to override the system.
MAZDA RADAR CRUISE CONTROL
WITH STOP & GO FUNCTION (IF EQUIPPED)
CANCEL/OFF
Distance Control
(Longer /
Shorter )
MODE (ON)
Cruise
Control (SET+ /
RESUME/
SET –)
MRCC with Stop & Go
function Set Switch
DISTANCES BETWEEN
VEHICLES
(at 50 mph) DISPLAY
Long
(about 164 ft)
Medium (about 131 ft)
Short
(about 98 ft)
Extremely Short
(about 82 ft)
2364256 17a CX-5 SSG 030117.indd 263/1/17 5:51 PM
Page 31 of 58
m{zd{ cx-5 30
NOTE: Any driver vehicle input (e.g., turn signal, steering or
acceleration, hands off, Traction Control System switch off) will
cancel warning and steering assist.
The steering operation assist for the Lane-keep Assist System and Lane Departure Warning System can be turned off. Refer to the
Owner’s Manual for further information.
Use the LAS and LDWS switch to turn the system ON or OFF.WARNING:
The Lane
Departure Warning
System (LDWS) is
not an automatic
driving system.
• The recognition
ability of the
Lane Departure
Warning
System (LDWS)
is limited.
• Over-reliance
on the system
could lead to
an accident.
• Always stay
on course using
the steering
wheel and
drive with care.
LANE-kEEP ASSIST SYSTEM /
LANE DEPARTURE WARNING SYSTEM
(IF EQUIPPED)
INDICATOR LIGHT* ACTIVE DRIVING
DISPLAY MULTI-
INFORMATION DISPLAY CONDITION
The painted road lane lines are
not recognized OR one side
is recognized OR the vehicle speed is less than 37 mph.
**
Both side painted road lane
lines are recognized at vehicle speeds of 37 mph or more.
1: Warning (Flashes)
Warning is triggered when vehicle deviates from its lane (depending on personalization setting).
1. When equipped with Active Driving Display.
2. When not equipped with Active Driving Display.
2
: No Active Driving Display
OFF
indicator
turns on.LAS and LDWS OFF
* When the steering assistance is off, indicator light is NOT displayed.
** When the steering assistance is off, indicator light is NOT displayed.
LAS and LDWS Switch
2364256 17a CX-5 SSG 030117.indd 303/1/17 5:51 PM
Page 34 of 58
33 MAZDAUSA.COM
BLIND SPOT MONITORING SYSTEM
BLIND SPOT MONITORING (BSM)
The BSM system is designed to assist the driver by monitoring blind spots on the left
and right sides of the vehicle in certain situations, such as lane changes.
•
If your vehicle speed is 6 mph or more, the BSM will warn you of
vehicles in the detection area by illuminating the BSM warning lights located on the left and right door mirrors.
•
If you operate a turn signal in the direction of an illuminated
BSM warning light, the system will also warn you with a beep
(depending on personalization setting, p. 15) and a warning light
will flash.
•
BSM sensors are located under the
left and right rear bumper areas.
The BSM system may not operate properly if the rear bumper is dirty,
so keep the rear bumper area clean
and free of bumper stickers.
NOTE:
•
The BSM can assist the driver in
confirming the safety of the surroundings, but is not a
complete substitute.
•
The driver is responsible for
ensuring safe lane changes and other maneuvers.
•
Always pay attention to the direction
in which the vehicle is traveling
and the vehicle’s surroundings.
•
The BSM does not operate when the vehicle speed is
lower than about 6 mph.
•
The BSM system volume can be adjusted in personalization
settings (p. 15).
Turning BSM System Off:
Turning the BSM system off will turn off both the light and sound indicators. To turn the BSM System off, refer to the "Personalization Features" in the Owner's Manual.
The BSM OFF indicator in the instrument cluster will turn on to indicate the BSM system is off.
NOTE: Turning the BSM system will also turn off the Rear Cross Traffic Alert System.
WARNING:
BSM is only a
supplementary
system to help
aid in monitoring
blind spots;
however, BSM
has limitations.
The system may
not detect all
vehicles, especially
a motorcycle. Do
not rely solely on
the BSM. Relying
solely on the
BSM may cause
an unexpected
accident resulting
in death or serious
injury. Make sure
to look over your
shoulder before
changing lanes.
Refer to your Owner’s Manual
for complete details.
Your
Vehicle
Detection Areas
BSM Warning Light
2364256 17a CX-5 SSG 030117.indd 333/1/17 5:52 PM
Page 36 of 58
35 MAZDAUSA.COM
LIGHTING / TURN SIGNALS
LIGHTING CONTROL / TURN SIGNAL LEVER
NOTE: The Daytime Running Lights (DRL) automatically turn on when the ignition is
switched ON. To disable/enable this feature, see your Authorized Mazda Dealer.
NOTE: You can adjust the timing of the Auto Headlights OFF and the sensitivity of the
Auto Light Control. See MAZDA CONNECT SETTINGS (p. 15).
(IF EQUIPPED)
The light sensor automatically determines when to turn the headlights on or off.
Turns tail, parking, dashboard, and headlights on.
THREE-FLASH SIGNAL
To signal a lane change, push the turn signal lever up or down halfway and release. The turn
signal indicator will only flash three times. See Personalization
Features to activate.
Turns fog lights on only when headlights are on.
Turns tail, parking, and dashboard lights on.
Pull to
Flash
High
Beams Push for
High Beams
Lighting
Control/Turn Signal Lever
2364256 17a CX-5 SSG 030117.indd 353/1/17 5:52 PM
Page 38 of 58
37 MAZDAUSA.COM
ADAPTIVE FRONT-LIGHTING SYSTEM
(IF EQUIPPED)
ADAPTIVE FRONT-LIGHTING SYSTEM (AFS)
AFS automatically turns the headlight beam to the right or left in conjunction with the
direction of the steering wheel.
The AFS improves the direction of headlight illumination while cornering and only works when the vehicle is moving.
NOTE: With AFS, it is normal to see the headlights move and hear the sound of the
headlight leveling motors at the front of the vehicle when the ignition is ON.
The system will need to be reset if the vehicle battery has been disconnected or the system fuse has been replaced. Please refer to your Owner’s Manual for easy-to-follow resetting instructions.
VEHICLE SETTINGS
AFS can be turned off using Vehicle Settings in MAZDA CONNECT (p. 15).
Without AFS Without AFS
With AFS
With AFS
2364256 17a CX-5 SSG 030117.indd 373/1/17 5:52 PM
Page 39 of 58
m{zd{ cx-5 38
HIGH BEAM CONTROL
(IF EQUIPPED)
HIGH BEAM CONTROL (HBC)
With HBC, the headlights are switched to high beams at speeds above 18 mph when there are no vehicles in front of your vehicle or approaching in the opposite direction.
The HBC system switches to low beam when: •
You are approaching a vehicle or a vehicle is approaching in the opposite direction.
• Driving on roads lined with street lights or well-lit cities and towns.
• At speeds lower than 12 mph.
To turn HBC on: 1 Turn the headlight switch to the AUTO position.
2 Push the headlight lever forward to the High Beam position.
NOTE: When the HBC system is on, the HBC indicator light in the instrument cluster will
illuminate (green). The High Beam indicator light will turn on (blue) when the HBC system
switches to high beam and will turn off when the HBC system switches to low beam.
Push for
High Beams
Turn to the
AUTO position
2364256 17a CX-5 SSG 030117.indd 383/1/17 5:52 PM
Page 46 of 58
45 MAZDAUSA.COM
GLOSSARY OF WARNING AND INDICATOR LIGHTS
IMPORTANT:
When your Mazda Connect display setting is set on “AUTO”, the instrument
cluster and display may become dimmer when the headlights are on. If the display and instrument cluster become too dim or too bright when the headlights are on, simply rotate
the dimmer knob located on your instrument cluster to adjust the brightness.
Traction Control System OFF
Low Engine Oil Pressure
Traction Control System/ Dynamic
Stability Control
On: TCS/DSC malfunction
Flashing: TCS/DSC operating
Shift Position
Advanced key detected
Advanced key not detected (p. 5)
Power Steering Malfunction
Airbag/Front Seat Belt
Pretensioner System Malfunction
Turn Signals/Hazard Warning
All-Wheel Drive ON
Flashing: Stop vehicle/
tow to Mazda dealer.
Check Engine
Master Warning
Smart Brake Support and
Smart City Brake Support
Flashing Red: SBS and SCBS
are operating.
Smart Brake Support and
Smart City Brake Support OFF
Amber: SBS and/or SCBS malfunction.
Tire Pressure Monitoring System
Warning* (p. 7)
On/Warning Beep: Low tire pressure in one or more tires.
Flashing: TPMS malfunction.
Security
Cruise Main ON (Amber)/
Cruise Set ON (Green)
Automatic Transaxle Warning
Lights ON (Exterior) (p. 35)
INSTRUMENT CLUSTER
Type "Å" Instrument Cluster (with LCD multi-information display) shown.
Refer to Owner's Manual for type "B" instrument cluster (without multi-information display) information.
Fuel
Gauge
LCD Information
Display
Dashboard Illumination/
Dimmer1/Trip Meter2
Speedometer
Tachometer
Shift
Position Odometer/
Trip Meter
2364256 17a CX-5 SSG 030117.indd 453/1/17 5:53 PM
Page 47 of 58
m{zd{ cx-5 46
INSTRUMENT CLUSTER
Type "Å" Instrument Cluster (with LCD multi-information display) shown.
Refer to Owner's Manual for type "B" instrument cluster (without multi-information display) information.
Blind Spot Monitoring OFF
(p. 33)
Seat Belt Unbuckled/Malfunction
Headlight High Beams ON
Electric Parking Brake
Brake Warning
Parking brake on/
low brake fluid/malfunction
Adaptive Front-lighting System
OFF (p. 37)
Charging System Malfunction
Mazda Radar Cruise Control
Stop & Go Function and AUTOHOLD
Door Ajar
Liftgate Ajar
Low Washer Fluid Level
Anti-lock Brake
System Malfunction
Low Fuel Level
Check Fuel Cap
Perform Maintenance
High Beam Control ON
Mazda Radar Cruise Control
ON (White)
SET (Green)
SPORT Mode ON
LED Headlight
Brake Pedal Operation Demand
Lane-keep Assist System and
Lane Departure Warning System
TPMS NOTE: Low ambient temperature and/or high altitude causes tire pressures to
drop and may turn the TPMS warning light on. If the warning light comes on, check the tire pressure and fill the tires as soon as possible, preferably before moving the vehicle
and warming up the tires. Tire pressure should be checked when the tires are cold.
See your Owner’s Manual for more details and explanations.
1 Rotate the knob to adjust the brightness of the instrument cluster and other dashboard illuminations.
2 Push to toggle between trip meter (A & B). When a trip meter is selected, push and hold to reset to zero.
TYPE B
Information Display
ENGINE COOLANT TEMPERATURE LIGHTS
Since this vehicle does not use an engine coolant temperature
gauge, red and blue engine coolant temperature lights are used to indicate high and low coolant temperature.
Red Coolant Temperature
FLASHING: Engine is starting to
run hot. Drive slowly to reduce
engine load.
ON: Engine is overheating.
Safely pull over to the side of the road and turn the engine off.
Refer to the Owner’s Manual for
more information. Blue Coolant Temperature
ON: Engine coolant is cold and
no warm air is available for heater/defroster.
OFF: Engine coolant is warm and
warm air is available for heater/
defroster. The light may stay on for a few minutes after start-up
when the engine is cold, but the vehicle can be driven with the light on or off.
2364256 17a CX-5 SSG 030117.indd 463/1/17 5:53 PM