MAZDA MODEL CX-5 2017 Smart Start Guide (in English)
Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL CX-5, Model: MAZDA MODEL CX-5 2017Pages: 58, PDF Size: 4.81 MB
Page 31 of 58
m{zd{ cx-5 30
NOTE: Any driver vehicle input (e.g., turn signal, steering or
acceleration, hands off, Traction Control System switch off) will
cancel warning and steering assist.
The steering operation assist for the Lane-keep Assist System and Lane Departure Warning System can be turned off. Refer to the
Owner’s Manual for further information.
Use the LAS and LDWS switch to turn the system ON or OFF.WARNING:
The Lane
Departure Warning
System (LDWS) is
not an automatic
driving system.
• The recognition
ability of the
Lane Departure
Warning
System (LDWS)
is limited.
• Over-reliance
on the system
could lead to
an accident.
• Always stay
on course using
the steering
wheel and
drive with care.
LANE-kEEP ASSIST SYSTEM /
LANE DEPARTURE WARNING SYSTEM
(IF EQUIPPED)
INDICATOR LIGHT* ACTIVE DRIVING
DISPLAY MULTI-
INFORMATION DISPLAY CONDITION
The painted road lane lines are
not recognized OR one side
is recognized OR the vehicle speed is less than 37 mph.
**
Both side painted road lane
lines are recognized at vehicle speeds of 37 mph or more.
1: Warning (Flashes)
Warning is triggered when vehicle deviates from its lane (depending on personalization setting).
1. When equipped with Active Driving Display.
2. When not equipped with Active Driving Display.
2
: No Active Driving Display
OFF
indicator
turns on.LAS and LDWS OFF
* When the steering assistance is off, indicator light is NOT displayed.
** When the steering assistance is off, indicator light is NOT displayed.
LAS and LDWS Switch
2364256 17a CX-5 SSG 030117.indd 303/1/17 5:51 PM
Page 32 of 58
31 MAZDAUSA.COM
DISTANCE RECOGNITION SUPPORT SYSTEM
(IF EQUIPPED)
Vehicle ahead
The distance area
between vehicles is
illuminated in white.
DISTANCE RECOGNITION SUPPORT SYSTEM (DRSS)
The Distance Recognition Support System (DRSS) measures the distance between
your vehicle and the vehicle ahead. DRSS uses a radar sensor (front) while the vehicle speed is 19 mph or faster and indicates a recommended distance to maintain between the vehicles. Furthermore, if your vehicle approaches a vehicle ahead more closely
than the appropriate distance to maintain between the vehicles, the vehicle ahead indication in the display is illuminated in white to advise the driver to keep a safe
distance from the vehicle ahead.
DISPLAY
DISTANCE BETWEEN
VEHICLES
(at 25 mph) About
82 ft About
66 ft About
49 ft About
33 ft
DISTANCE BETWEEN
VEHICLES
(at 50 mph) About
164 ft About
131 ft About
98 ft About
65 ft
2364256 17a CX-5 SSG 030117.indd 313/1/17 5:51 PM
Page 33 of 58
m{zd{ cx-5 32
TRAFFIC SIGN RECOGNITION
(IF EQUIPPED)
TRAFFIC SIGN RECOGNITION (TSR) SYSTEM
The Traffic Sign Recognition (TSR) System helps prevent the driver from overlooking
traffic signs and provides support for safe driving by displaying traffic signs on the
Active Driving Display. TSR recognizes traffic signs by using the Forward Sensing
Camera (FSC) or the navigation system while driving.
When vehicle speed exceeds the speed limit sign displayed in the Active Driving Display,
the system notifies the driver with an indication in the Active Driving Display and a
warning sound.
ACTIVE DRIVING DISPLAY GUIDE
The TSR displays the SPEED LIMIT
(including auxiliary signs), DO NOT ENTER , and
traffic STOP
signs.
NOTE: The Traffic Sign Recognition (TSR) System is not supported in some countries
or regions. For more information, consult an Authorized Mazda Dealer. The Traffic
Sign Recognition (TSR) System operates only if the navigation system SD card (Mazda
Genuine) is inserted in the SD card slot. Consult an Authorized Mazda Dealer for details.
SPEED LIMIT SIGN DISPLAYEDSPEED LIMIT SIGN RECOGNIZEDSTOP SIGN RECOGNIZED AND DISPLAYED
2364256 17a CX-5 SSG 030117.indd 323/1/17 5:51 PM
Page 34 of 58
33 MAZDAUSA.COM
BLIND SPOT MONITORING SYSTEM
BLIND SPOT MONITORING (BSM)
The BSM system is designed to assist the driver by monitoring blind spots on the left
and right sides of the vehicle in certain situations, such as lane changes.
•
If your vehicle speed is 6 mph or more, the BSM will warn you of
vehicles in the detection area by illuminating the BSM warning lights located on the left and right door mirrors.
•
If you operate a turn signal in the direction of an illuminated
BSM warning light, the system will also warn you with a beep
(depending on personalization setting, p. 15) and a warning light
will flash.
•
BSM sensors are located under the
left and right rear bumper areas.
The BSM system may not operate properly if the rear bumper is dirty,
so keep the rear bumper area clean
and free of bumper stickers.
NOTE:
•
The BSM can assist the driver in
confirming the safety of the surroundings, but is not a
complete substitute.
•
The driver is responsible for
ensuring safe lane changes and other maneuvers.
•
Always pay attention to the direction
in which the vehicle is traveling
and the vehicle’s surroundings.
•
The BSM does not operate when the vehicle speed is
lower than about 6 mph.
•
The BSM system volume can be adjusted in personalization
settings (p. 15).
Turning BSM System Off:
Turning the BSM system off will turn off both the light and sound indicators. To turn the BSM System off, refer to the "Personalization Features" in the Owner's Manual.
The BSM OFF indicator in the instrument cluster will turn on to indicate the BSM system is off.
NOTE: Turning the BSM system will also turn off the Rear Cross Traffic Alert System.
WARNING:
BSM is only a
supplementary
system to help
aid in monitoring
blind spots;
however, BSM
has limitations.
The system may
not detect all
vehicles, especially
a motorcycle. Do
not rely solely on
the BSM. Relying
solely on the
BSM may cause
an unexpected
accident resulting
in death or serious
injury. Make sure
to look over your
shoulder before
changing lanes.
Refer to your Owner’s Manual
for complete details.
Your
Vehicle
Detection Areas
BSM Warning Light
2364256 17a CX-5 SSG 030117.indd 333/1/17 5:52 PM
Page 35 of 58
m{zd{ cx-5 34
REAR CROSS TRAFFIC ALERT
(IF EQUIPPED)
REAR CROSS TRAFFIC ALERT (RCTA)
The RCTA is designed to alert the driver of oncoming traffic when backing out of a parking spot. RCTA is active when your vehicle is in reverse and your vehicle speed is 0 mph to 9 mph.
When the BSM sensors detect a moving object, the RCTA will notify the driver with indicators and sound:
• Rear view monitor and outside mirror flashing indications.
Refer to your Owner’s Manual for complete details.
WARNING:
RCTA is only a
supplementary
system to help aid
when backing up; however, RCTA
has limitations.
The system does not detect all
vehicles, especially motorcycles. Do
not rely solely on the RCTA. Relying
solely on the RCTA may cause
an unexpected
accident resulting in serious injury.
Always back up slowly.
Reference Image
Rear view monitor
Object
Detected
Object
Detected
2364256 17a CX-5 SSG 030117.indd 343/1/17 5:52 PM
Page 36 of 58
35 MAZDAUSA.COM
LIGHTING / TURN SIGNALS
LIGHTING CONTROL / TURN SIGNAL LEVER
NOTE: The Daytime Running Lights (DRL) automatically turn on when the ignition is
switched ON. To disable/enable this feature, see your Authorized Mazda Dealer.
NOTE: You can adjust the timing of the Auto Headlights OFF and the sensitivity of the
Auto Light Control. See MAZDA CONNECT SETTINGS (p. 15).
(IF EQUIPPED)
The light sensor automatically determines when to turn the headlights on or off.
Turns tail, parking, dashboard, and headlights on.
THREE-FLASH SIGNAL
To signal a lane change, push the turn signal lever up or down halfway and release. The turn
signal indicator will only flash three times. See Personalization
Features to activate.
Turns fog lights on only when headlights are on.
Turns tail, parking, and dashboard lights on.
Pull to
Flash
High
Beams Push for
High Beams
Lighting
Control/Turn Signal Lever
2364256 17a CX-5 SSG 030117.indd 353/1/17 5:52 PM
Page 37 of 58
m{zd{ cx-5 36
WIPER / WASHER CONTROL
CAUTION:
If the ignition is ON, turn
the AUTO wipers OFF
when going through a car
wash or while cleaning or touching the windshield.
WINDSHIELD WIPER / WASHER CONTROL LEVER
(IF EQUIPPED)
The rain sensor senses the amount of rainfall and
turns the wipers on or off.
Rotating the inner ring
clockwise (away from you)
creates greater wiper sensitivity and makes the
wipers move faster. The + position increases wiper
speed. Rotating the inner ring counterclockwise
(toward you) makes the wipers move
slower. The - position
decreases wiper speed.
Normal speed
Intermittent
REAR WINDOW
WIPER/WASHER
(hold as desired)
NOTE: Vehicles not equipped with AUTO wipers will have
INT wipers. Set the lever to INT and choose an interval timing by rotating the ring between fast and slow.
Pull to
dispense
windshield
washer fluid.MIST
AUTO
LO
HI
12
3
Windshield
Wiper/Washer
Control Lever
2364256 17a CX-5 SSG 030117.indd 363/1/17 5:52 PM
Page 38 of 58
37 MAZDAUSA.COM
ADAPTIVE FRONT-LIGHTING SYSTEM
(IF EQUIPPED)
ADAPTIVE FRONT-LIGHTING SYSTEM (AFS)
AFS automatically turns the headlight beam to the right or left in conjunction with the
direction of the steering wheel.
The AFS improves the direction of headlight illumination while cornering and only works when the vehicle is moving.
NOTE: With AFS, it is normal to see the headlights move and hear the sound of the
headlight leveling motors at the front of the vehicle when the ignition is ON.
The system will need to be reset if the vehicle battery has been disconnected or the system fuse has been replaced. Please refer to your Owner’s Manual for easy-to-follow resetting instructions.
VEHICLE SETTINGS
AFS can be turned off using Vehicle Settings in MAZDA CONNECT (p. 15).
Without AFS Without AFS
With AFS
With AFS
2364256 17a CX-5 SSG 030117.indd 373/1/17 5:52 PM
Page 39 of 58
m{zd{ cx-5 38
HIGH BEAM CONTROL
(IF EQUIPPED)
HIGH BEAM CONTROL (HBC)
With HBC, the headlights are switched to high beams at speeds above 18 mph when there are no vehicles in front of your vehicle or approaching in the opposite direction.
The HBC system switches to low beam when: •
You are approaching a vehicle or a vehicle is approaching in the opposite direction.
• Driving on roads lined with street lights or well-lit cities and towns.
• At speeds lower than 12 mph.
To turn HBC on: 1 Turn the headlight switch to the AUTO position.
2 Push the headlight lever forward to the High Beam position.
NOTE: When the HBC system is on, the HBC indicator light in the instrument cluster will
illuminate (green). The High Beam indicator light will turn on (blue) when the HBC system
switches to high beam and will turn off when the HBC system switches to low beam.
Push for
High Beams
Turn to the
AUTO position
2364256 17a CX-5 SSG 030117.indd 383/1/17 5:52 PM
Page 40 of 58
39 MAZDAUSA.COM
AUDIO CONTROLS
(IF EQUIPPED)
AUDIO OPERATION
The following icons are displayed on the screen:
SOURCES: Displays the Audio menu to change the audio source (AM, FM,
XM, Bluetooth
®, Aha, Pandora, Stitcher,
USB, AUX).
Auto Memory: Displays a list of the
10 strongest radio stations. Because
station strength changes as you drive,
select the Update Station List icon to re-scan for strong stations.
Favorites: Displays a list of your
favorite AM, FM, and XM radio stations.
HD Radio: Switches HD Radio on/off.
Scan: Scans radio stations or songs
(scanning stops at each one for five seconds). Select again to stop.
Tuner: Displays manual radio tuner.
Tag: Saves artist and title and sends
them to your Apple device (for Apple
devices with USB use only).
Seek Previous/Next: Selects previous
or next receivable radio station or song. Push and hold to change the radio station continually.
Settings: Adjusts the audio quality
level (bass, treble, etc.).
The following icons are displayed on the USB and BT music screens only:
TRACK LIST: Displays the track list.
REPEAT: Repeats the current song.
Select again to stop.
SHUFFLE: Plays the songs in random
order. Select again to stop.
PLAY/PAUSE: Plays and pauses
the song.
New Mazda vehicles equipped with SiriusXM® Satellite Radio will receive an introductory four-
month trial subscription that starts on the day the vehicle is sold. Enjoy over 150 channels including commercial-free music, plus sports, comedy, entertainment, news and much more.
To start listening to SiriusXM, select XM from audio sources, then push channel up and down to listen to over 150 channels. If you do not hear audio, please activate service to your radio with a simple refresh process.
1 Scroll to XM Radio, go to channel 1 and push “previous” to channel 0 to find your radio ID.
2
Go to siriusxm.com/refresh and enter radio ID or call 1-855-MYREFRESH (1-855-697-3373).
HD RADIO
HD radio has a special receiver which allows it to receive digital broadcasts (where available) in addition to the analog broadcasts it already receives. Digital broadcasts have better
sound quality than analog broadcasts as digital broadcasts provide free, crystal clear audio.
When the HD radio button is ON (red), there could be a noticeable difference in sound
quality and volume when a change from digital to analog signals occurs. If the sound
quality and volume become noticeably diminished or cut off, select the HD button to turn HD radio OFF (not red).
2364256 17a CX-5 SSG 030117.indd 393/1/17 5:52 PM