battery MAZDA PROTEGE 1992 Workshop Manual

T SWITCHES
03UOTX-026
H&N CAP
03UOTX-02 8
03UOTX-02s
SWITCH
Removal / Installation
Ignition switch
1. Remove the negative battery cable.
2. Remove the steering column cover.
3. Remove the screw and the ignition switch.
4. Install in the reverse order of removal.
Hazard warning switch
1. Remove the meter hood.
2. Remove the screws and the hazard switch.
3. Install in the reverse order of removal.
Cruise control switch
(set/coast and resume/accel switch)
1. Remove the steering wheel cap.
2. Remove the cruise control switch as shown in the figure.
3. Install in the reverse order of removal.
Inspection
1. Check for continuity between the terminals with an
ohmmeter.
Remote control door mirror switch
CLASS DIRECTION a b c d i k I
UP o---o
0 0
1 UP
I I lo! I-l7ol
o----O: Indicates continuity
T-20

T SWITCHES
03UOTX-03 i5
k i g f d
b
OBUOTX-0: $6
03UOTX-03
23UOTX-01
Power window main switch
(Power switch)
Terminal
Position a h
OFF
ON
0 0
C--O: indicates continuity
(Power window switch)
o---O: Indicates continuity
Power window switch (Each door)
Terminal
UP A B C D E
0 0
0 0
OFF 0 0
0 0
DOWN 0 0
0 0
m: Indicates continuity
Panel lamp control switch
1. Remove the switch.
2. Apply battery voltage to terminal ‘Id” and ground to termi-
nal “g”.
3. Check that the voltage at terminal “a” changes linearly when
turning the switch.
Switch
Min. position
Max. position Voltage
1ov
ov
T-22

I
EXTERIOR LIGHTING SYSTEM
Headlights do not operate (Low and/or High)
(Without cruise)
I
Turn ON light switch (second position)
I
Check head 30A main fuse Short circuit
0
Confirm battery voltage on R w Repair harness (Main fuse - Combination switch) L
I
0 OK
Confirm battery voltage on R wire (when Low) and/or
R/W wire (when High) of the combination switch Replace the combination switch
Confirm battery voltage on R wire (when Low) and/or
R/W wire (when High) of the headlight Repair harness (Combination switch - Headlight)
I
0
Confirm continuity on B wire of the headlight
Repair harness (Headlight - Body ground)
Burnt out bulb
23UOTX-017 Headlights do not operate (Low and/or High)
I
(With cruise)
I
Turn ON light switch (second position)
Short circuit
0 OK
Confirm battery voltage on W/R wire of the combination switch
I
8) C OK Repair harness (Main fuse - Headlight relay)
I
Replace the headlight relay
1
Repair harness (Headlight relay - Combination switch)
Confirm battery voltage on R wire (when Low) and/or
R/W wire (when High) of combination switch connector Replace the combination switch
1
Q 1 OK
Disconnect headlight connector. Confirm battery voltage
on R wire (when Low) and/or on RIW wire (when High)
of connector
,o OK
Repair harness (Combination switch - Headlight)
1
I
Confirm continuity on B wire of the headlight connector
to ground Repair harness (Headlight - Body ground)
I
T-32
OK _ Replace the bulbs
23UOTX-018

EXTERIOR LIGHTING SYSTEM T
Headlights either do not operate or are dim Low-High beam or passing flasher does not
J operate
Burnt out bulb or poor grounding J
03UOTX-049 Defective combination switch
03UOTX-050
(Canada) Daytime running lights (DRL) do not operate
Confirm that headlights operate with the light switch ON
(second position) OK
Turn OFF the light switch and turn ON the ignition
switch when parking level pulling
I
Check head 30A main fuse OK
Check DRL resistor OK Repair DRL resistor 10A fuse
Confirm battery voltage on R and L/G wire of the DRL NG
relay Repair harness (Fuse - DRL relay)
I
I
Check the DRL relay
Repair DRL relay
1 OK
Confirm battery voltage on (BRNV) wire of the DRL con-
trol unit NG
Repair harness (DRL relay - DRL control unit) OK
Confirm battery voltage on (L/G) wire of the DRL control NG
unit Repair harness (Rear wiper fuse - DRL control unit) OK
Confirm continuity of (G/R) wire of the DRL control unit x Repair harness (DRL control unit - Parking brake
to ground switch) or check the parking brake switch 1 OK
Confirm continuity on (B) wire of the DRL control unit to
NG
ground Repair harness (DRL control unit ground) OK
-1 NG
Confirm approx. 8V on the DRL resistor Repair harness (DRL control unit - DRL headlight)
I
Confirm battery voltage on (
Confirm approx. 8V on (R/W) wire of the DRL resistor Repair harness (DRL resistor - DRL relay)
Repair harness (DRL control unit - DRL resistor)
23UOTX-019
T-33

EXTERIOR LIGHTING SYSTEM
Turn Signal lights do not operate
Check meter 15A fuse A an
I
0 OK
Confirm battery voltage on BI Repair harness (Fuse - Turn switch) OK
1 ~,-
Check the turn signal switch NG
(Refer to page T-27 or T-28) Replace the turn switch
1 OK
Turn ignition switch to ON. Turn the signal switch to
RIGHT or LEFT
Confirm battery voltage on G or Y wire of the flasher
unit Repair harness (Turn switch - Flasher unit)
6) OK
Confirm battery voltage on B Repair harness (Fuse - Flasher unit)
1
1 OK
Check the flasher unit (Refe Replace the flasher unit
I
(B OK
Confirm battery voltage on G/W (G/B) wire of the turn
signal light NG _
Repair harness (Flasher unit - Turn signal light) @ OK
Confirm continuity on B wire of the turn signal light to
ground OK
Replace the bulb NG
Repair harness (Turn signal light - Body ground)
23UOTX-020
T-35

I
EXTERIOR LIGHTING SYSTEM
Only hazard function does not operate
Check the hazard warning Replace the hazard switch
1 I
1 OK
Confirm continuity on B wire of the hazard switch to
ground Repair harness (Hazard switch - Body ground)
OK
I I
Push the hazard switch to activate
OK -2
Confirm continuity on B wire of the flasher unit to body
ground NG
Repair harness (Flasher unit - Hazard switch)
OK
NG
Check the flasher unit (Refer
Replace the flasher unit
Normal
I
Only one side of signal operates
13UOTX-026 .,
Check the turn signal switch
(Refer to page T-27 or T-28)
I Replace the turn switch
1 OK
Turn ignition switch to ON. Turn the signal switch to
defective side
Repair harness (Turn switch - Flasher unit)
Replace the flasher unit
Confirm battery voltage on G/W (G/B) wire of the turn
signal light NG-
- Repair harness (Flasher unit - Turn signal light)
I OK
Confirm continuity on B wire of the turn signal light to
ground NG
Repair harness (Turn signal light - Body ground)
Replace the bulb
T-36
I OK
23UOTX-021

I
EXTERIOR LIGHTING SYSTEM
TNS system (side marker, license, tail, illumination
light) does not operate
I
Turn ON light switch
I
Check tail 15A fuse
I OK
Confirm battery voltage on W/B wire of TNS relay
connector Repair harness (Main fuse - TNS relay)
I OK
Check TNS relay (Refer to page T-42) Replace the TNS relay OK
Confirm battery voltage on L/G wire of the combination NG
switch Repair harness (TNS relay - Combination switch)
I OK
Confirm battery voltage on RIB wire of front and rear
side marker, license, tail, and illumination light
connectors Repair harness (TNS relay - Lights)
I OK
Confirm continuity on B wire of above connectors to
ground NO
- Repair harness (Lights - Body ground)
Replace the bulbs
I
23UOTX-022
T-38

I
EXTERIOR LIGHTING SYSTEM
Both stoplights do not operate when brake pedal is
depressed
i
Check stop 20A fuse
I Short circuit
Confirm battery voltage on G/W wire of the stoplight
switch
I Repair harness (Fuse - Stoplight switch) OK
Check the voltage with the brake pedal depressed
I
BD
c
Confirm battery voltage on G Replace the stoplight switch
8) OK
Confirm battery voltage on G Repair harness (Stoplight switch - Stoplight)
(B
Confirm continuity on B wir Repair harness (Stoplight - Body ground)
I I I
I
Replace the bulb
I
23UOTX-023 One stoplight does not come on
Burnt out bulb or faulty grounding
03UOTX-058
T-40

EXTERIOR LIGHTING SYSTEM
Inspection
Headlight (Headlight relay)
1. Disconnect the headlight relay connector and remove the
relay.
2. Check for continuity between terminals of the relay.
d b
23UOTX-024
C a
~
d b C
a
iYiFz3l
23UOTX-02
C a
~
d b
23UOTX-026 C
a
a
d b Qec a
I I h f d
03UOTX-063 ve: Battery voltage
Connecting to
a b c d
v0 Ground
- -
0 0
a b 0 0
o--<>: Indicates continuity
Headlight (DRL relay)
1, Disconnect the DRL relay connector and remove the relay.
2. Check for continuity between terminals of the relay.
VB: Batterv voltaae
Connecting t- n a b C d
Ve Ground
- -
C-3 I 0
r-- a b
o---O: Indicates continuity 0 1 0
Front combination light (TNS relay)
1. Disconnect the TNS relay connector and remove the relay.
2. Check for continuity between terminals of the relay.
VB: Batterv voltawe
Connecting to
a b C d VB Ground
-
0 0
I a b
O-4: Indicates continuity 0 1 0 1
Front combination light (Flasher unit)
1. Check for continuity between terminals of the flasher unit.
a-g
a-h
c-a
c-d
c-e
c-f
r--n
t------ X
e-a X
g-d X
X e-c X
g-e X
0 e-d X
g---f X
0 e-f X
P-h X
0
e-g X h-a 0
0 e-h X h-c 0
I ” Y
C-h
d-a
C
I
x 1 h-d 1 n I 0 f-a
0 f-c X h-e 0
X f-d X h-f 0
X f-e X
h-g 0
F d-
0: Indicates continuity X: No continuity
T-42

INTERIOR LAMP SYSTEM T
IG key illumination does not operate
Check room IOA fuse NG
- Short circuit
0 OK
Confirm battery voltage on V Defective harness (Fuse - Joint box), or bulb
0 OK
Confirm continuity on B wire of the joint box (CPU) to
ground Repair harness (Joint box - Body ground)
OK
When any door is opened, confirm that interior lamp
comes on
OK NG
~ Defective harness (Joint box - Door switch), or door
switch
Confirm continuity between N terminal of JB-09 connec- _ NG
-
tor and B terminal of JB-03 connector Repair harness (JB-09 - JB-03)
I OK
Replace CPU
23UOTX-029
Inspection
Door switch (Front sides with passive belt)
Confirm continuity between the R/W wire and the B wire of
the door switch connector (in passive motor connector).
Condition Continuity
Push X
Not push 0
0: Indicates continuity X: No continuity
03UOTX-181 Door switch (Others)
Confirm for continuity between the terminals of the door switch.
Condition Continuity
Push X
Not push 0
0: Indicates continuity X: No continuity
1 I OSJOTX-082
T-51