technical data MAZDA PROTEGE 1992 Workshop Manual

1992
Mazda
CONTENTS
Protege
Workshop
Manual
FOREWORD
This workshop manual is intended for use
by service technicians of Authorized Mazda
Dealers to help them service Mazda vehicles.
For proper repair and maintenance, a
thorough familiarization with this manual is im-
portant, and it should always be kept in a han-
dy place for quick and easy reference.
All the contents of this manual, including
drawings and specifications, are the latest avail-
able at the time of printing. As modifications
affecting repair or maintenance occur, relevant
information supplementary to this volume will
be made available at Mazda dealers. This
manual should be kept up-to-date.
Mazda Motor Corporation reserves the right
to alter the specifications and contents of this
manual without obligation or advance notice.
All rights reserved. No part of this book may
be reproduced or used in any form or by any
means, electronic or mechanical-including
photocopying and recording and the use of
any kind of information storage and retrieval
system-without permission in writing.
Mazda Motor Corporation
HIROSHIMA, JAPAN
APPLICATION:
This manual is applicable to vehicles beginning
with the Vehicle Identification Numbers (VIN)
shown on the following page.
Title
General Information Section
Pre-Delivery Inspection and
Scheduled Maintenance Services
SOHC
Engine
DOHC
Lubrication System
Cooling System
Fuel and Emission Control System
Engine Electrical System
Clutch
FSM-R
Manual Transaxle
GSM-R
Automatic Transaxle
Front and Rear Axles
Steering System
Braking System
Wheels and Tires
Suspension
Body
--
Body Electrical System
Heater and Air Conditioner Systems
Technical Data
Special Tools
Parts Index
Wiring DNvam
I Part No. 5209-10-91 F)
9999~95-019(3-92)
o 1991 Mazda Motor Corporation
PRINTED IN USA, JUL. ‘91
1270-l O-91 G
(9999-95-0178-92)

TD
TECHNICAL DATA
MEASUREMENTS .................................... TD- 2
ENGINE (B6 AND BP SOHC)
ENGINE (BP DOHC) ... .................................................. ;;- f
LUBRICATION SYSTEM ........................... TDI 6
COOLING SYSTEM .................................. TD- 6
FUEL AND EMISSION CONTROL
SYSTEMS ............................................. TD- 9
ENGINE ELECTRICAL SYSTEM ................ TD-10
CLUTCH ................................................. TD-11
MANUAL TRANSAXLE (F5M-R) ................ TD-12
MANUAL TRANSAXLE (GSM-R) ................ TD-13
AUTOMATIC TRANSAXLE ....................... TD-14
FRONT AND REAR AXLES.. .....................
STEERING SYSTEM ................................ ;;-;;
-
BRAKING SYSTEM .................................. TD-16
WHEELS AND TIRES ............................... TD-19
SUSPENSION ......................................... TD-19
BODY ELECTRICAL SYSTEM ................... TD-20
HEATER AND AIR CONDITIONER
SYSTEMS ............................................. TD-21
STANDARD BOLT AND NUT TIGHTENING
TORQUE .............................................. TD-21
23UTDX-001

TD TECHNICAL DATA
MEASUREMENTS
I ._.____2_ nem
Overall length
Overall width
Overall height
Wheel base
Front tread
Rear tread Body ) mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in) PRfWFr.f! . . ..s .-VW Hatchback 4,355 (171.5) 4,155 (163.6)
1,675 (65.9) 1,670 (65.7)
1,375 (54.1) 1,380 (54.3)
2,500 (98.4) 2,450 (96.5)
1,430 (56.3)
1,435 (56.5)
Bl. ENGINE (B6 AND BP SOHC)
1 Type
1 Cylinder arrangement and number Engine
86 SOHC BP SOHC
^ . . _
,?
I
uasollne, 4-cyw
. . *. 4
in-line 4-cyrinaer
Pentroof
1
I Combustion chamber I Multispherical
J Valve system OHC, belt-driven OHC, belt-driven 16 valves
. , I (3.07 x 3.29) 83.0 x 85.0 (3.27 x 3.35)
Total piston displacement cc (cu in) 1,597 (97.4) 1,839 (112.2)
Compression ratio 9.3 8.9
) Standard 1,236 (12.6, 179)-300 1,197 (12.2, 173)300
I
863 (8.8, 125)-300 834 (8.5, 121)300 1 Bore x Stroke
mm (in) I 78.0 x 83.6
Compression pressure
kPa (kg/cm’, psi)-rpm
E cvlinders 1 Maximum difference
196 (2.0, 28)
I
, ------- ---- -J - IN Open BTDC 14O 2O
Close ABDC 50°
Valve timing
Open BBDC 52O 55O
EX
Close ATDC 12O 8O
IN 0 Maintenance-free I \/AIo &-in --
Valve clearance EX 0 Maintenance-free
(Warm engine) mm (in) / ,,syi: 1
IN 0 Maintenance-free
I , EX 0 Maintenance-free
I Cylinder head
Height
Distortion
Grinding Valve and T _
Valve head diameter
Valve head margin thickness
Valve face angle IN mm (in) EX
IN
mm b-4 Fx mm (in) 107.4-107.6 (4.228-4.236)
mm (in) 0.15 (0.006) max. 0.10 (0.004) max.
mm (in) 0.20 (0.008) max. 0.10 (0.004) max.
37.9-38.1 (1.492-l ,500) 29.9-30.1 (1.177-1.185)
31 .Q-32.1 (1.256-l ,264) 24.85-25.15 (0.978-0.990)
0.8 (0.031) 0.9 (0.035)
1.1 10.043) 1 .o (0.039)
-, ,
\- I
IN 45O
EX 45O
I I Standard
IN
Minimum
Valve length mm (in)
EX Standard
Minimum I”L. I, \*.“cL
Valve stem diameter IN
mm On) EX 6.970-6.985 (0.2744-
6.965-6.980 (0.2742-
Guide inner diameter
I Valve stem-to-guide clearance mm (in) lTj7---- ,
Maximum 103.77 (4,085) 101.77 (4.007)
103.27 (4.066) 101.27 (3.987)
102.67 (4.042) 102.97 (4.054)
,n+ 47 IA noo
1 102.47 (4.034)
-0.2750) 5.970-5.985 (0.2350-0.2356)
-0.2748) 5.965-5.980 (0.2348-0.2354)
3.2760-0.2768) 6.01-6.03 (0.2366-0.2374)
0.025-0.060 (0.001 O-0.0024)
0.030-0.065 (0.001 l-0.0026)
-.
I
mm (in) 1 7.01-7.03 (r ‘
1 IN
Guide projection (Height “A”) IN
mm (in) Ex 13.2-l 3.8 (0.520-
13.2-13.8 (0.520-
TD-2

TECHNICAL DATA TD
Item Engine
B6 SOHC BP SOHC
Valve seat
IN
45O
Seat angle
EX 45O
Seat contact width IN
mm 04 EX 1.1-l .7 (0.043-0.067) 0.8-l .4 (0.031-0.055)
1.1-l .7 (0.043-0.067) 0.8-l .4 (0.031-0.055)
IN Standard 39 (1.5354) 42.5 (1.673)
Seat sinking mm (in) Maximum 40.5 (1.594) 44.0 (1.732)
EX Standard 39 (1.5354) 41.0 (1.614)
Maximum 40.5 (1.594) 42.5 (1.673) Valve spring
Standard mm (in) 43.66 (1.7188) 46.12 (1.8157)
IN
Minimum N (kg, Ib)/mm (in) 224-253 (22.8-25.8, 205-231 (20.9-4X3.5,
Free length 50--57)/35.5 (1.398) 46-52)/39 (1.535)
Standard mm (in) 43.66 (1.7188) 43.61 (1.7169)
EX
Minimum N (kg, Ib)/mm (in) 224-253 (22.8-25.8, 129-147 (13.1-15.0,
50-57)/35.5 (1.398) 29-33)/37.5 (1.476)
Out-of-square mm (in) 1 Maximum 1.52 (0.060) IN...l.61 (0.063) EX...1.52 (0.060)
Lobe height mm (in) IN
EX Standard 36.451 (1.4351) 35.993 (1.4170)
Wear limit 36.251 (1.4272) 35.793 (1.4092)
Standard 36.451 (1.4351) 36.273 (1.4281)
Wear limit 36.251 (1.4272) 36.073 (1.4202)
Front 43.440-43 ,460 No.1 & 43.440-43.460
(1.7102-l .7 ‘110) No.5 (1.7102-1.7110)
43.430-43 ,445 No.2 & 43.425-43.450
mm (in) Center
(1.7098-l .7 ‘108) No.4 (1.7096-l .7106)
. , L
Rear 43.440-43.460 No’3 43.41 o-43.435
(1.7102-l .7110) (1.7091-1.7100)
1 Out-of-round 0.05 (0.002) max.
Front 0.055-0.095 No.1 & 0.040-0.075
(0.0021-0.0037) No.5 (0.0016-0.0030)
e--I-.. 0.060-O. 105 No.2 84 0.035-0.080
1041) No.4
“.“-.-..“” (O.OOi 4-0.0031)
Rear 0.055-0.095 0.050-0.095
(0.0021-0.0037) No.3
(0.0020-0.0037)
1 Maximum
0.15 (0.006)
0.01 (0.0004)
0.03 (0.0012)
0.05-0.18 (0.0020-0.0071) 0.06-0.19 (0.0024-0.0075)
n ‘1 m *no Journal diameter
Camshaft hearinn nil cIewanr.F? mm tin I b,er’Ler I (0.0023--0.c
Camshaft runout mm (in) Maximum
Camshaft end play mm (in) Standard
Maximum
I Rocker arm and rocker arm shaft
Rocker arm inner diameter mm (in) 18.000-18.027 (
Rocker arm shaft diameter mm (in)
17 9.59-17 981) I “.L ~“.““O,
lN...19.000--19.027 (0.7480-0.7491)
o.7087-o’70g7) EX...19.000-19.033 (0.7480-0.7493)
I .““” -- -
0 7070-0.7079) 18.959-18.980 (0.7464-0.7472)
lN...0.020-0.068 (0.0008-0.0027)
Rnrkx arm tn shaft clearance
mm (in Standard
I .Y”,.VG 11.,, .” -,,-.. “,“-.“, .I”
““” ,“‘I o.020-o.068 (“~ooo8-o~oo27) EX...O.020-0.074 (0.0008-0.0029)
Maximum 0.10 (0.004) Cylinder block
Height mm (in) 221.5 (8.720)
Distortion mm (in) 0.15 (0.006) max.
Grinding mm (in) 0.20 (0.008) max.
^. , ,
78.006-78.013 (3.0711-3.0714) 183.006-83.013 (3.2679-3.2682)
-.n nr,. -,n fin,% ,n nnnr
” nn’n’ ’ “- T)cc 83.263 (3.2778-3.2781) Cylinder bore diameter stanaara size
mm (in) 0.25 (0.010) oversize IU.L3cl-/U.dDJ (J.uouu-J.uo IL) 1 OJ.LJU--
0.50 (0.020) oversize 78.506-78.513 (3.0908-3.0911) ) 83.506-
Cylinder bore taper and out-of-round mm (in) 0.019 (0.0007) ma: 83.513 i3.2876-3.2879)
I(.
TD-3

TD TECHNICAL DATA
I-
Item Enainc , 66 SOHC BP SOHC
Piston
, 1
-97 n-1 7-7 /t-r”
82.954-82.974
I -’
Piston diameter
Standard size I I I.Y34--1 l.YlG + I,-. nnnn
n r,Prx< > Measured at 90’ to pin (J.uoYY-mJoYo) (3.2659-3.2667)
bore axis and 165mm
I 78.211-78.217 83.211-83.217
(0.650 in) below oil ring 0.25 (0.010) oversize
(3.0792-3.0794) (3.2760-3.2763)
groove
0.50 (0.020) oversize 78.461-78.467 83.461-83.467
mm (in)
(3.0890-3.0892) (3.2859-3.2861)
Piston-to-cylinder clearance mm (in) Standard 0.039-0.052 (0.0015-0.0020)
Maximum 0.15 (0.006) Piston ring
Thickness
End gap
(Measured in cylinder) mm (in) Top
Second
Top
Second
mm (in) Oil (rail) I 1.47-l .49 (0.0579-0.05E
1.47-l .49 (0.0579-0.05E
0.15-0.30 (0.006-0.01~
0.15-0.30 (0.006-0.01; I Connectina rod and connectin
‘I ‘I 0.20-0.70 (0.008-0.028) 0.20-0.70 (0.008-0.028)
Maximum 1 .o (0.039) 1 .o (0.039)
Top 1,520-l ,535 (0.0598-0.0604) 1,520-l ,535 (0.0598-0.0604)
Ring groove width in piston
mm (in) Second 1.520-l ,535 (0.0598-0.0604) 1.520-l ,535 (0.0598-0.0604)
Oil
d d 117-4 04 (0 1583-O 1591) f ‘.02-3.04 (0.1189-0.1197) 117-4 04 ..“_ ..“. (0 1583-O 1591) f 1.02-3.04 (0.1189-0.1197)
\-“--- -’ - I
Piston ring-to-ring groove clearance Top 0.030-0.065 (O.O( 312-0.0026)
mm (in) Second 0.030-0.065 (O.O( 312-0.0026)
I
( Maximum
0 15 [email protected]) Piston pin
Diameter u,a, I KaEil mm (in) 1 111111 ,888, 19.974-19.980 (0.7864-0.7866) .“.“. _.__ J (0.7864-0.7866)
Interference in connecting rod ‘(0.0005-0.0015)
mm (In) 1 0.013-0.037 (0.0005-0.0015)
lnstallina pressure
N (kg, lb) 1 4,90614,715 (500-l ,500, 1 ,l oo-3,300) 4,90614,715 (500-l ,500, 1 ,l oo-3,300)
Length (Ceiter to center) Length (Ceiter to center) lg rod bearing lg rod bearing
mm (in) 1 mm (in) 1 132.85-132.95 (5.2303-5.2342) 132.85-132.95 (5.2303-5.2342)
Bending Bending mm (in) 1 mm (in) 1 0.075 (0.0030) max./50 (1.97) 0.075 (0.0030) max./50 (1.97)
Small end bore mm (in) 19.943-19.961 (0.; ‘852-0.7859) ‘852-0.7859)
Big end bore
mm (in) 48.000-48.016 (1 .f 3898-l .8904) 3898-l .8904)
Big end width mm (in) 21.838-21.890 f0.f 3598-0.8618)
I Connecting rod side clearance mm (in) Standard
! 0.11 O-O.262 (0.0043-0.0103)
Maximum 0.30 (0.012) Crankshaft
Crankshaft runout
mm (in) 0.04 (0.0016) max.
Standard Standard 49.938-49.956 (1.9661-I .9668)
size
Minimum 49.904 (1.9647)
0.25 (0.010) Standard 49.704-49.708 (1.9568-l .9570)
Main journal diameter undersize
Minimum 49.652 (1.9548)
mm (in)
0.50 (0.020) Standard 49.454-49.458 (1.9470-l .9472)
undersize
Minimum 49.402 (1.9450)
0.75 (0.030) Standard 49.204-49.208 (1.9372-I .9373) 1 -
undersize
Minimum 49.152 (1.9351) -
~.. Crankshaft
3598-0.8618j 1
I 0.11 O-O.262 (0.0043-0.0103)
0.30 (0.012)
1 Main iournal taoer and out-of-round
mm (in) I 0.05 (0.020) max.
Standard Standard 44.940-44.956 (i.7693-1.7699)
size
Minimum 44.908 (1.7680)
0.25 (0.010) Standard 44.690-44.706 (1.7594-l .7601)
undersize
Crankpin diameter mm (in) Minimum 44.658 (1.7582)
0.50 (0.020) Standard 44.440-44.456 (1.7496-I .7502)
undersize
Minimum 44.408 (1.7483)
0.75 (0.030) Standard 44.190-44.206 (1.7398-l .7404)
undersize
Minimum 44.158 (1.7385)
0.05 (0.020) max.
b
I I , I - \“‘---I 0.05 (0.020) max.
b
I I Crankuin taper and out-of-round
mm (In) I Main bearing
I
Main journal bearing oil clearance Standard
I 0.018-0.036 (0.0
mn-, ,i” .A- :-- -
c-l*,- ‘^’
Available undersized bearing
TD-4
007-0.0014)
I& II I I \” ‘,
, I”ld*llT,UIr1
I “. I J (U.004)
mm (in) 0.25 (O.OlO), 0.50 (0.020) 0.75 (0.030) . . . 86 Otily

TECHNICAL DATA TD
r-
RP sm.lc: I Item
Crankpin bearing Engine
86 SOHC
I -. VW.._
Crankpin bearing oil clearance mm (in) Standard 0.028-0.068 (0.001 l-0.0027)
Maximum 0.10 (0.004)
Available undersized bearing mm (in)
0.25 (O.OlO), 0.50 (0.020) 0.75 (0.030) Thrust bearing
Crankshaft end play mm (in) Standard 0.080-0.282 (0.0031-0.0111)
Maximum 0.30 (0.012)
Standard size 2.500-2.550 (0.0984-0.1004)
Bearing width mm (in) 0.25 (0.010) oversize 2.625-2.675 (0.1033-0.1053)
0.50 (0.020) oversize 2.750-2.800 (0.1083-0.1102)
0.75 (0.030) oversize 2.875-2.925 (0.1132-0.1152)
1 Timing belt
Belt deflection mm (in)/98 N (10 kg, 22 lb) 1 11 .o-13.0 (0.43-0.51) 82.
ENGINE (BP DOHC) Item
Type
Cylinder arrangement and number BP DOHC
Gasoline, 4-cycle
In-line 4-cylinders
-. I
Combustion chamber
Valve svstem DOHC, belt-d
Bore x Stroke
Total piston displacement ventroot
riven
(3.2:
mm (in) 1 83.0 x 85.0
cc (cu in) ]
7x3.35)1 1,839 (112.2)
I 16 valves I 9.0
-300
mn Compression ratio
Standard 1,256 (12.8, 182)
Compression pressure Minimum 883 (9.0, 128)-Z kPa (kglcm2,
Psi)-rPm
Maximum dif
‘ference
between eat -, h cvlinder 196 (2.0, 28)
IN Open BTDC 5O
Valve timing Close ABDC 48’
EX Open BBDC 56O
Close ATDC .4 In
IY-
IN
mm (in) EX 0 Maintenance-l
Valve clearance
0 Maintenance-i ‘ree
‘me Cylinder head
Height mm (in)
Distortion mm (in)
Grinding mm (in)
Standard
Cylinder head-to-HLA clearance mm (in) Maximum Valve and valve guide 133.8-134.0 (5.268-5.276)
0.10 (0.004) max.
0.10 (0.004) max.
0.025-0.066 (0.0010-0.0026)
0.18 (0.0071)
Valve head diameter IN
mm (in) EX 32.9-33,l (1.295-l ,303)
27.85-28.15 (1.096-1.108)
Valve head margin thickness IN
mm On) Fx 0.9 (0.0354)
1 .o fO.0393)
1 Valve face angle . .
I
FX I I
Valve length IN
Standard 101.34 (3.9898)
mm (in) Minimum 100.84 (3.9701)
Standard 101.44 (3.9937) I -, .
I
Valve stem diameter EX
Minimum loo.94 i3.974oj
IN
mm (in) - EX 5.970-5.985 (0.2350-0.2356)
5.965-5.980 (0.2348-0.2354)
mm (in) I
. , , 6.01-6.03 (0.23 166-0.2374)
1 IN
I 0.025-0.060 (0.0010-0.0024)
3.0012-0.0026)
( Maximum 0.20 (0.008)
I
TD-5

TD TECHNICAL DATA
Item Engine
BP DOHC
Guide projection (Height “A”) IN
mm (in) EX 18.3-l 8.9 (0.720-0.744)
_-j
18.3-l 8.9 (0.720-0.744)
Valve seat
Seat angle
Seat contact width IN 45O
EX 45O
IN
mm (in) EX 0.8-l .4 (0.031-0.055)
0.8-l .4 (0.031-0.055)
Seat sinking
Valve spring
Free length
Out-of-square
Camshaft IN Standard 45.0 (1.7716)
mm (in) Maximum 46.5 (1.831)
EX Standard 45.0 (1.7716)
Maximum 46.5 (1.831)
Standard mm (in) 46.26 (1.821)
Minimum N (kg, Ib)/mm (in) 224-253 (22.8-25.8, 50--57)/39.5 (1.555)
mm (in) 1.62 (0.064) max.
I C+^~rl^.A
44.094 (1.7360)
43.894 (1.7281)
44.600 (1.7560)
44.400 (1.7480) IN 3Ldl l”dl u
Cam height mm (in) Wear limit
EX Standard
Wear limit
Standard
Journal diameter mm (in) (No.l-No.5) 25.940-25.965 (1.0213-l .0222)
Out-of-round 0.03 (0.001) max.
Standard
Camshaft bearing oil clearance mm (in) (No-1-No.5) 0.035-0.081 (0.0014-0.0032)
Maximum 0.15 (0.006)
Camshaft runout mm (in) 0.03 (0.0012) ma
IX.
Camshaft end play mm (in) ’ Standard 0.07-O. 19 (0.0028-0.0075)
Maximum I
I n 9 m mm “.L \“.“““,
Cylinder block
Height
Distortion
Grinding mm (in) 221.5 (8.720)
mm (in) 0.15 (0.006) max.
mm (in) 0.20 (0.008) max.
Cylinder bore diameter Standard size 83.006-83.013 (3.2679-3.2682)
mm (in) 0.25 (0.010) c oversize 83.256-83.263 (3.2778-3.2781)
n.vl IO0701 I -.--
\-----I Jversize 83.506-83.513 (3.2876-3.2879)
Cylinder bore taper and out-of-round mm (in) 0.019 (0.0007) max.
Piston
I
I I
Piston diameter 82.954-82.974 (3.2659-3.2667)
Measured at 90” to pin
bore axis and 16.5mm
83.21 l-83.21 7 (3.2760-3.2763)
(0.650 in) below oil ring
groove
mm fin) 0.50 (0.020) oversize 83.461-83.467 (3.2859-3.2861)
r~ Piston to cylinder clearance
mm On) (Standaid 0.039-0.052 (0.0015-0.0020)
Piston ring
Thickness
End gap
(Measured in the cylinder) mm (in) ‘W
Second
Top
Second
mm (in) Oil (rail)
Maximum
Too I .‘t, - I .ct3 (“.“a, 3-u
1.47-l .49 (0.0579-C
0.1%0:30 (0.006--C
0.15-0.30 (0.006-C
I I.01 2)
0.20-0.70 (0.008-0.028)
1.0 (0.039)
1,520-l
,535 (0.0598-0.0604)
1.52-l .54 (0.0598-0.0606)
3.02-3.04 (0.1189-O. 1197)
I Ring groove width in piston mm (In) n
;_A
TD-6

TECHNICAL DATA TD
Item Engine
BP DOHC
?ston ring-to-ring groove clearance Piston pin
3iameter -fop
C----A 0.030-0.065 (0.0012-0.0026)
n n-an n fi7t-i m n
mm (in) imL;UI IU
I “.“a”-“.“, ” \“.~012-0.0026)
Maximum 0.15 (0.006)
mm (in) 19.987-19.993 (0.7869-0.7871)
.0002-0.0005)
~004-0.0011) ‘iston-to-piston pin clearance
Connecting rod bush-to-piston pin clearance Connecting rod and connecting rod bearing
-ength (Center to center)
3ending
Small end bore (Bush inner diameter) mm (in) 1 -0.005-0.013 (-0
mm (in) 1 0.010-0.027 (0.0
I I mm (in) 132.85-132.95 (! 5.230-5.234)
mm (in) 0.075 (0.0030) m lax.150 (1.97)
mm (in) 20.003-20.014 (0.
I , 7875-0.7880)
3ig end bore mm (in) 48.000-48.016 (1.8898-l .8904)
Big end width mm (in) 21.838-21.890 (0.8598-0.8618)
I Cl0nAa.A
Connecting rod side clearance mm (in) I YI’:“‘Yal” 0.11 O-O.262 (0.0043-0.0103)
1 rvraxrmum +
I 0.30 (0.012) Crankshaft
Crankshaft runout mm (in) 0.04 (0.0016) max.
Standard Standard 49.938-49.956 (1.9661-l .9668)
size
Minimum 49.904 (1.9647)
0.25 (0.010) Standard 49.704-49.708 (1.9568-l .9570)
49.652 (1.9548)
Main journal diameter undersize
Minimum
mm (in) 0.50 (0.020) Standard
undersize
Minimum 49.402 (1.9450)
0.75 (0.030) 1 Standard 49.204-49.208 (1.9372-l .9373)
I undersize
I j Minimum
I I
I 49.152 (1.9351)
Main journal taper and out-of-round mm (in) 0.05 (O.OiO) max.
I .7699)
44.908 il.76801
I .7601) Standard Standard
size
Minimum
0.25 (0.010) Standard I 44.940-44.956 (1.7693-l
I
44.690-44.706 il.7594’-1
Crankpin diameter undersize
Minimum 44.658 (1.7582) ’
mm (in) 0.50 (0.020) Standard 44.440-44.456 (1.7496-1.7502) I
undersize I MinimrIm . -. 7 44.408 (1.7483)
0.75 (0.030) Standard 44.190-44.206 (1.7398-l .7404)
undersize
Minimum 44.158 (1.7385)
Crankpin taper and out-of-round mm (in) j 0.05 (0.020) max. Main bearing
Main journal bearing oil clearance Standard 0.018-0.036 (0.0007-0.0014)
mm (in) Maximum 0.10 (0.004)
-m I)
Available undersized bearing mm (in) 0.25 (0.010) 0.50 (0.020) 0.75 (0.030) Crankpin bearing
Crankpin bearing oil clearance
bearing 3Lalluaru
mm (in) .,-..:--..-
Available undersized Thrust bearing I mL^^A^--I
I rvraxrmurTr
mm (in)
Crankshaft end play 0.028-0.068 (0.001 I-0.0027)
0.10 (0.004)
0.25 (O.OlO), 0.50 (0.020) 0.75 (0.030)
Ct-Y.TdQ*A 0.080-0.282 (0.0031-0.0111) ..- -.
0.30 (0.012) I
Standard si7e _._.._
-. - _.-- 2.500-2.550 (0.0984-o. 1004)
Cl c)C In n+A\ nthysize
2.625-2.675 (0.1033-O. 1053)
?rsize 2.750-2.800 ,
(0.1083-0.1102)
0.75 (0.030) oversize 2.875-2.925 (0.1132-0.1152) mm (in) I- Bearing width Timing belt
Belt deflection mm (in)/98 N (10 kg, 22 lb) 1 9.0-l 1.5 (0.35-0.45)
TD-7

TECHNICAL DATA
D. LUBRICATION SYSTEM
Item I I bhricatinn mothnd
Engine
B6 SOHC BP SOHC
Force-fed BP DOHC 1
Requlated pressure kPa (kg/Cm”, p
Inner rotor tooth tip to outer rotor Standard
I-‘---- -.----,
clearance mm (in) Maximum 0.20 (0.0078)
Outer rotor to body clearance mm (in) Standard 0.09-0.18 (0.0035-0.0071)
Maximum 0.22 (0.0087)
Side clearance mm (in) Standard 0.03-0.11 (O.pniq n nnn=’
Maximum n4rl ‘-
“” I r-“.““+..I,
I “. I ‘t (U.0055)
I
1
Oil filter
_ Type
Relief pressure differential
Engine oil
I
Capacity
liters (US qt, Imp qt)
Grade
I Viscosity Full-flow, paper element
kPa (kg/cm’, psi) 1 78-l 18 (0.8-I .2, 1 l-l 7) Tntal /An, nnr*inol 3.4 (3.6, 3.0) 1 4.0 (4.2, 3.5)
3.0 (3.2, 2.6) 1 3.6 (3.8, 3.2)
VII 111Lb1 0.17 (0.18, 0.15)
API Service SG Energy Conserving II (ECQ
1
SA!f InW-Xl 1~ Above -25% (-13OF _ .-.. --
I
I
number
1 Below O’C (32OF) SAE 5W-30
1
E. COOLING SYSTEM
Cooling method EnginelTransaxle
MTX ] ATX 1 MTXl
Water-cooled, forced circulation
J B6 SOHC BP SOHC BP DOHC
, ATX 1 MTX ) ATX
LThermostat
Type Opening temperature
Full-open temperature
Full-open lift
Radiator
_ Type
Cap valve opening pressure
Cooling circuit checking pressure Wax, two-stage
“C (OF) Sub: 83.5-86.5 (182--188), Main: 86.5-89.5 (188-193)
OC (OF) 100 (212)
mm (in) Sub: 1.5 (0.06) min., Main: 8.0 (0.31) min.
Corrugated fin
kPa (kg/cm2, psi) 74-103 (0.75-1.05, 11-15)
kPa (kg/cm’, psi) 103 (1.05, 15)
~..
Cooling fan
Type Electric .-
Number of blades 4
_.---- _I___-
Outer diameter mm (in) 320 (12.6)
--_ ~~-
Capacity w-v 80-12 - 160-12 80-l 2 160-12
6.6 Hi : 13.3
6.6 Hi : 13.3
Current A
Low : 8.8 Low : 8.8
_------ ._____
Water thermoswitch
“c (OF) 1
OFF-ON 97 (207)
I--.
Radiator thermoswitch
__-I____-
OFF+ON “C (OF) 1 1105 (221)( - (105 (221)
TD-8

TECHNICAL DATA TD
Item
Coolant Engine/Transaxle B6 SOHC BP SOHC BP DOHC
MTX 1 ATX 1 MTX 1 ATX 1 MTX 1 ATX
Capacity
liters tus qt, Imp qt) (5Z.4) (8.E.3) (5&4) (SE.3) (5.?i.4) (S.E.3)
Coolant protection Volume percentage %
Specific gravity at
Water Coolant 20% (68OF)
Antifreeze solution Above -16OC (3OF)
65 35 1.054
Above -26OC (-15OF) 55 45 1.066
I Above -4OOC (-40°F) 45 55
1.078
F. FUEL AND EMISSION CONTROL SYSTEMS Item
idle speed*‘**
Ignition timing** Fuel pump
Maximum output pressure Fuel filter Engine
B6 SOHC BP SOHC BP DOHC
vm 700-800
BTDC 6O--8O 4O---6O 90-l 10
kPa (kg/cm*, psi) 1 441-637 (4.5-6.5, 64-92) ‘Type
Low-pressure side Nylon element (in fuel pump)
High-pressure side Paper element Pressure regulator
Regulating pressure kPa (kg/cm*, psi) 1 265-314 (2.7-3.2, 38-46) Injector
Type
High-ohmic
Type of drive Electromechanical
Resistance n 12-16 Idle speed control (ISC) valve
Type
Rotary
Resistance n ] 11-13 Purge control solenoid valve
Resistance n 1 23-27 Water thermosensor
-20°C( -4OF) 14.6-17.8
Resistance k6 20°C( 68QF) 2.21-2.69
40% (104OF) 1.0-l .3
80°C(1760F) 0.29-0.35 Airflow meter
E2++Vs Fully closed 20-600 q D Fully open 20-l ,000
E~HVC 200-400
Resistance g Ez++THAA -2O%(-4OF) 13,600-18,400
(Intake air 20%( 68OF) 2,210-2,690
thermosensor)
60°C(1400F) 493-667
Eic*Fc Fully closed 00
Fully open 0 Fuel tank
Capacity liters (US gal, Imp gal) I
Hatchback 50 (13.2, 11.0) PROTEGE . . . . 55 (14.5, 12.1) Air cleaner
Element type Oil permeated Fuel
Specification Unleaded regular (RON 91 or higher)
*’ With parking brake applied (Canada)
*’ TEN terminal of diagnosis connector grounded
TD-9