MERCEDES-BENZ C-Class COUPE 2017 CL205 Owner's Manual
Manufacturer: MERCEDES-BENZ, Model Year: 2017, Model line: C-Class COUPE, Model: MERCEDES-BENZ C-Class COUPE 2017 CL205Pages: 354, PDF Size: 8.66 MB
Page 291 of 354

Checking theoil level usin gthe oil dip-
stick
Example
XPull oil dipstick :out of th edipstick guide
tube.
XWipe off oil dipstick :.
XSlowly slide dipstick :intothe guide tub eto
th es top, and tak eitout again after approx-
imately 3seconds.
If th elevelisb etween MIN mark =and MAX
mark ;,theoil leve liscorrect.
XIf theoil leve lhas dropped to MIN mark =or
below, add 1. 1USqt(1.0l iter) of engineo il.
Adding engine oil
HEnvironmental note
When addingo il, takecaren otto spill any. If
oil enters th esoil or waterways, it is harmful to
th ee nvironment.
!Only use engineo ils and oil filters that have
been approved for vehicle swithas ervicesys-
tem. You can obtain alist of th eengineo ils
and oil filters tested and approved in accord- anc ewitht heMercedes-Ben zSpecifications
for Servic eProduct satany Mercedes-Benz
Servic ecenter.
Damage to th eengineore xhaust system is
caused by th efollowing:
Rusinge ngineo ils and oil filters that have not
been specifically approved for th eservice
system
Rreplacin gengineo il and oil filters after the
interval for replacements pecifiedbythe
servic esystem has been exceeded
Rusinge ngineo il additives.
!Do no tadd to omucho il. addingt oomuch
engineo il can result in damagetot heengine
or to th ecatalyti cconverter. Hav eexcess
engineo il siphoned off.
Example
XTurn cap :counter-clockwise and remove it.
XAdde ngineo il.
If th eoil leve lisatorb elow theMIN mar kon
th eo il dipstick ,add 1. 1USq t(1.0 l)of engine
oil.
XReplace cap :on the filler neck and turn
clockwise.
Ensure that the cap locks into place securely.
XCheck the oil level again with the oil dipstick
(Ypage 289).
Further information on engine oil (
Ypage 346).
Additional service products
Important safety notes
GWARNING
Certain components in the engine compart-
ment,s uch as the engine, radiator and parts
of the exhaust system, can become very hot.
Working in the engine compartment poses a
risk of injury.
Where possible, let the engine cool down and touch only the components described in the
following.
GWARNING
The cooling system is pressurized, particularly
when the motor is warm. If you open the cap,
you could be scalded if hot coolant sprays out.
There is arisk of injury.
Engine compartment289
Maintenance and care
Z
Page 292 of 354

Let the engine cool down before you open the
cap. Wear gloves and eye protection. Slowly
open the cap to relieve pressure.
GWARNING
Windshield washer concentrate could ignite if it comes into contact with hot engine compo-
nents or the exhaust system. There is arisk of
fire and injury.
Make sure that no windshield washer con-
centrate is spilled next to the fillern eck.
Checking coolant level
XPark the vehicle onalevel surface.
Only check the coolant level when the vehicle
is on alevel surface and the engine has cooled
down.
XTurn the SmartKey to position 2in the ignition
lock (Ypage 131).
or
XOn vehiclesw ith KEYLESS-GO, press the
Start/Stop button twice (Ypage 131).
XCheck the coolant temperature display in the
instrument cluster (Ypage 201).
The coolant temperature must be below
158 ‡(70 †).
XTurn the SmartKey to position 0in the ignition
lock (Ypage 131).
or
XOn vehiclesw ith KEYLESS-GO, pul lthe Start/
Stop button from the ignition lock
(
Ypage 131).
XSlowl yturn cap :half aturn counter-clock-
wise to allow excess pressure to escape.
XTurn cap :further counter-clockwise and
remove it.
If the coolant is at the level of marker bar =
in the fillern eck when cold, there is enough
coolant in coolant expansio ntank ;.
If the coolant level is approximately 0.6 in
(1.5 cm) above marker bar =in the fillern eck
when warm, there is enough coolant in expan-
sion tank ;.
XIf necessary ,add coolant that has been tested
and approved by Mercedes-Benz.
XReplace cap :and turn it clockwise as far as
it wil lgo.
For further information on coolant, see
(
Ypage 347).
Adding washe rfluid to the windshield
washe rsystem
XTo open: pullcap : upwards by the tab and
open.
XAdd the premixed washer fluid.
XTo close: press cap :onto the fillern eck
until it engages.
If the washer flui dlevel drops belowt he recom-
mended minimum of 1liter, amessag eappears
in the multifunction display prompting you to
add washer flui d(
Ypage 245).
Further information on windshield washer fluid/
antifreeze (
Ypage 348).
ASSYST PLUS
Servic emessage
The ASSYST PLUS service interval display
informs you of the next service due date.
290ASSYST PLUS
Maintenancea nd care
Page 293 of 354

Information on the type of service and service
intervals (see the separate Maintenance Book-
let).
You can obtain further information from an
authorized Mercedes-Benz Center or at
http://www.mbusa.com (USA only).
iThe ASSYST PLUS service interval display
does not show any information on the engine
oil level.O bserve the notes on the engine oil
level (
Ypage 288).
The multifunction display shows aservice mes-
sage for several seconds, e.g.:
RService AinXXD ays
RServiceADue
RService AOverdue by XX Days
Depending on the operating conditions of the
vehicle,t he remaining time or distance until the
next service due date is displayed.
The letter A
orB,possibly in connection with a
number or another letter, indicates the type of
service. A
stands for aminor service and Bfor a
major service.
You can obtain further information from an
authorized Mercedes-Benz Center.
The ASSYST PLUS service interval display does
not take into account any periodsoft ime during
which the battery is disconnected.
Maintaining the time-dependent service sched-
ule:
XNote down the service due date displaye din
the multifunction display before disconnect-
ing the battery.
or
XAfter reconnecting the battery, subtract the
battery disconnection periodsf rom the ser-
vice date shown on the display.
Hiding aservicem essage
XPress the aor% button on the steering
wheel.
Displaying servic emessages
XSwitch on the ignition.
XUse ò on the steering wheel to call up the
list of menus.
XPress 9or: on the steering wheel to
select the Servicemenu and confirm with
a.
XPress 9or: on the steering wheel to
select the ASSYST PLUSsubmenu and con-
firm with a.
The service due date appears in the multi-
function display.
Information about Service
Resetting the ASSYST PLUS service
interval display
!If the ASSYST PLUS service interval display
has been inadvertently reset, this setting can
be corrected at aqualifieds pecialist work-
shop.
Have service work carried out as describedi n
the Maintenance Booklet. This may otherwise
leadtoi ncreased weara nd damage to the
major assemblies or the vehicle.
Aq ualifieds pecialist workshop, e.g. an author-
ized Mercedes-Benz Center, wil lreset the
ASSYST PLUS service interval display after the
service work has been carried out. You can also
obtain further information on maintenance
work, for example.
Special servic erequirements
The specifiedm aintenance interval takes only
the normal operation of the vehicle into
account. Under arduous operating conditions or
increased load on the vehicle,m aintenance
work must be carried out more frequently, for
example:
Rregular city driving with frequent intermediate
stops
Rif the vehicle is primarily used to travel short
distances
Ruse in mountainou sterrain or on poor road
surfaces
Rif the engine is often left idling for long periods
Under these or similar conditions, have, for
example ,the air filter, engine oil and oil filter
replaced or changed more frequently. Under
arduous operating conditions, the tires must be
checked more often. Further information can be obtained at aqualifieds pecialist workshop, e.g.
an authorized Mercedes-Benz Center.
ASSYST PLUS291
Maintenancea nd care
Z
Page 294 of 354

Drivingabroad
An extensive Mercedes-Ben zService networ kis
also available in other countries. You can obtain
further information from any authorized
Mercedes-Ben zCenter.
Car e
General notes
HEnvironmental not e
Dispose of empty packagin gand cleanin g
cloths in an environmentally responsible man -
ner.
!Fo rc leanin gyour vehicle, do no tuse any of
th ef ollowing:
Rdry, rough or har dcloths
Rabrasiv ecleanin gagents
Rsolvents
Rcleanin gagents containin gsolvents
Do no tscrub .
Do no ttou ch th esurfaces or protective films
wit hh ardo bjects ,e.g.a ringori cescraper.
You could otherwise scratch or damage th e
surfaces and protective film.
!Do no tparkt he vehicle fo ranextende d
period straight after cleanin git,particularly
after havin gcleaned th ewheels wit hwhee l
cleaner. Wheel cleaners could cause
increase dcorro sion of th ebrake discs and
brake pads/linings. Fo rthisr eason ,you
should drive fo rafewminutes after cleaning.
Brakin gheat sthe brake discs and th ebrake
pads/linings, thus drying them. The vehicle
can then be parked.
Regular car eofyour vehicle is aconditi on for
retainin gthe qualit yint he longterm.
Use car eproducts and cleanin gagents recom -
mended and approved by Mercedes-Benz.
Washing th evehicle an dcleaning th e
paintwor k
Automatic car was h
GWARNING
Brakin gefficiency is reduce dafter washin g
th ev ehicle. There is ariskofana ccident.
Afte rthe vehicle has bee nwashed, brake
carefully whil epayin gattenti on to th etraffic
condition suntil full braking powe risrestored .
!If DISTRONIC PLU SortheHOLD function is
activated, th evehicle brake sautomatically in
certain situations.
To preven tdamage to th evehicle, deactivat e
DISTRONIC PLU Sand th eHOLDf unction in
th ef ollowin goro ther similar situations:
Rwhen towin gthe vehicle
Rin th ecar wash
!Never clean your vehicle in aTouchless
Automatic Car Wash as these use special
cleanin gagents .These cleanin gagents can
damage th epaintwor korplasticparts .
!Mak esuret hat:
Rthes idew indows and th eslidin gsunroof
are full yclosed.
Rth ev entilation/heatin gisswitched of f(th e
OF Fb utto nhas bee npressed).
Rthew indshield wipe rswitch is at position 0.
Rthe3 60°c amera or rea rviewc amera is
switched off.
The vehicle may otherwise be damaged .
!If theSmartKey is within th ereard etection
range of KEYLESS-GO ,the followin gsitua-
tions, fo rexample, could lead to th euninte
n
-
tional opening of th etrunk :
Rusin gac ar wash
Rusingap owerwasher
Mak esuret hatthe SmartKey is at leas t10ft
(3 m) away from th evehicle.
!Mak esuret hatthe automatic transmissio n
is in neutral position Nwhen washin gyour
vehicle in atow-throu gh car wash .The vehicle
may otherwise be damaged .
ROperatingwitht he SmartKey:
Do no tremov ethe SmartKey from th eigni-
tion lock. Do no topent he driver's doo r
292Care
Maintenance an dcare
Page 295 of 354

when theengine is switche doff or at very
low speeds.O therwise, when in transmis-
sion position Dor Rthea utomatic trans-
mission will automatically switch to park
position Pand blockt hewheels.
ROperatin gwith th eStart/Stop button:
Do not open th edriver's door when the
engine is switche doff or at veryl ow
speeds.O therwise, when in transmission
position Dor Rth ea utomatic transmission
will automatically switch to park position P
and blockt hewheels.
Observe th efollowing to makes ure that the
automatic transmission stays in position Nneu-
tral:
Operatin gwith th eSmartKey and th eStart/
Stop button:
XMake sure that th eignitio nisswitche don.
XMake sure that th evehicle is stationary.
XDepress and hold th ebrakep edal.
Operatin gwith th eStart/Stop button only:
XEngage park position P.
XRelease thebrakep edal.
XRemoveS tart/Stop button fromi gnitionlock
(Ypage 131).
XInsert th eSmartKey int othe ignitio nlock.
XSwitch on th eignition.
XDepress and hold th ebrakep edal.
Operatin gwith th eSmartKey and th eStart/
Stop button:
XShif tton eutral N.
XRelease th ebrakep edal.
XRelease th eelectric parking brake, if neces-
sary.
XSwitch off th eignitio nand leave th eSma rtKey
in th eignitio nlock.
You can wash th evehicle in an automatic car
wash fromt heverys tart.
If th evehicle is veryd irty, pre-wash it bef
ore
cleaning it in an automatic car wash.
After using an automatic car wash, wipe off wax
fromt hewindshield and th ewiper blades. This
will prevent smearsa nd reducewiping noises
caused by residue on th ewindshield.
Washing by hand
In some countries, washingbyh and is only
allowed at specially equipped washingb ays.
Observe th elegal requirements in each country.
XDo not use hot water and do not wash the
vehicle in directs unlight.
XUseasofts ponge to clean.
XUse amild cleaning agent, such as acar
shampoo approved by Mercedes-Benz.
XThoroughly hose down th evehicle with agen-
tle jet of water.
XDo not pointt hewater jet directly towards the
air inlet.
XUse plenty of water and rinse out th esponge
frequently.
XRinse th evehicle with clean water and dry
thoroughly with achamois.
XDo not let th ecleaning agentd ry on thepaint-
work.
Carefull yremove all deposits of road salt as
soon as possible when driving in winter.
Power washers
GWARNING
The water jet fromac ircular jet nozzle (dirt
blasters) can cause invisible exterior damage
to th etires or chassis components. Compo-
nents damaged in this way may fail unexpect-
edly. Thereisar isk of an accident.
Do not use power washersw ith circular jet
nozzles to clean th evehicle. Have damaged
tires or chassis component sreplaced imme-
diately.
!Always maintain adistanc eofatl east
11.8 in (30 cm) between th evehicle and the
power washer nozzle. Information about the
correctd istanceisavailable fromt heequip-
mentm anufacturer.
Move th epower washer nozzle aroundw hen
cleaning your vehicle.
Do not aim directly at any of th efollowing:
Rtires
Rdoor gaps, roof gaps, joints, etc.
Relectrical components
Rbattery
Rconnectors
Care293
Maintenance and care
Z
Page 296 of 354

Rlights
Rseals
Rtrim
Rventilation slots
Damaged seals or electrical component scan
lead to leaks or failures.
!If the SmartKey is within the rear detection
rang eofK EYLESS-GO, the followings itua-
tions, for example, could lead to the uninten-
tional opening of the trunk:
Rusing acar wash
Rusing apower washer
Make sure that the SmartKey is at least 10 ft
(3 m) away fromt he vehicle.
!Edition1special model: partsofy our vehi-
cle are covered with adecorative foil. Main-
tain adistanc eofatl east 70 cm betwee nthe
foil-wrapped partsoft he vehicle and the noz-
zle of the high pressure cleaner.
Information about the correctd istanceis
available fromt he equipmentm anufacturer.
Move the power washer nozzle around when
cleaning your vehicle.
Cleaning th epaintwork
!Do not affix:
Rstickers
Rfilms
Rmagnetic plates or similar items
to painted surfaces. You could otherwise
damage the paintwork.
Scratches, corrosived eposits, areas affected by
corrosiona nd damage caused by inadequate
care cannot always be completely repaired. In
such cases ,visit aqualified specialist workshop.
XRemove dirt immediately, where possible,
while avoidingr ubbingtoo hard.
XSoak insect remainsw ith insect remover and
rinse off the treated areas afterwards.
XSoak bird droppings with water and rinse off
the treated areas afterwards.
XRemove coolant, brakef luid, tree resin,oils,
fuels and greases by rubbingg ently with a
clot hsoaked in petroleum ether or lighter
fluid.
XUse tar remover to remove tar stains.
XUse silicone remover to remove wax. If water no longer forms "beads" on the paint
surface, use the paint care products recommen-
ded and approved by Mercedes-Benz. This is the
case approximately everyt
hree to five months,
depending on the climat econdition sand the
care productu sed.
If dirt has penetrate dthe paint surfaceorift he
paint has becom edull, the paint cleaner recom-
mended and approved by Mercedes-Benz
should be used.
Do not use these care products in the sun or on
the hood while the hood is hot.
XUse asuitable touch-up stick, e.g. MB Touch-
Up Stick ,torepair slight damage to the paint-
work quickly and provisionally.
Matte finish care
!Never polish the vehicle or the light alloy
wheels. Polishingc auses the finish to shine.
!The followingmay cause the paint to
becom eshinya nd thus reducet he matte
effect:
Rstrong rubbingoft he paintwork with
unsuitable materials
Rfrequent use of automatic car washes
Rwashing the vehicle in directs unlight
!Never use paint cleaner, buffingorp olishing
products, or gloss preserver,e .g. wax. These
products are only suitable for high-gloss sur-
faces. Their use on vehicles with matt efinish
leads to considerable surfaced amage (shiny,
mottled areas).
Always have paintwork repairs carried out at a
qualified specialist workshop.
!Do not use wash programs with ahot wax
treatment under any circumstances.
Observe these notes if your vehicle has aclear
matt efinish. This will help you to avoid damage
to the paintwork due to incorrect treatment.
These notes also apply to light alloy wheels with ac lear matt efinish.
The vehicle should preferably be washed by
hand using asoft sponge, car shampooa nd
plent yofw ater.
Use only insect remover and car shampoof rom
the rang eofapproved Mercedes-Ben zcare
products.
294Care
Maintenance and care
Page 297 of 354

Cleaning thevehicle parts
Cleaning th ewheels
GWARNING
The wate rjet from acircular je tnozzle (dirt
blasters)c an causeinvisible exterior damage
to th etires or chassis components .Compo-
nent sdamaged in this way may fail unexpect-
edly. Thereisar iskofana ccident.
Do no tuse power washers withc ircular jet
nozzles to clean th evehicle .Haved amaged
tires or chassis components replaced imme-
diately.
!Do no tuse acidic wheel cleanin gproducts
to remove brak edust.T his coul ddamage
wheel boltsa nd brakecomponents.
!Do no tpark th evehicle for an extended
period straigh tafter cleanin git, particularly
after having cleane dthe wheelsw ithwheel
cleaner. Wheelc leaners couldcause
increased corrosion of th ebrak ediscsa nd
brak epads/linings. For this reason,y ou
should driv efor afew minute safter cleaning.
Brakin gheatst hebrak ediscsa nd thebrake
pads/linings, thus dryin gthem. The vehicle
can then be parked.
Cleaning th ewindows
GWARNING
You coul dbecome trapped by th ewindshield
wipersift heys tart moving while cleanin gthe
windshield or wiper blades.T hereisarisko f
injury.
Always switch off th ewindshield wipersa nd
th ei gnition before cleanin gthe windshield or
wiper blades.
!Do no tuse dry cloths, abrasive products,
solvents or cleanin gagents containing sol-
vents to clean th einside of th ewindows. Do
no ttou ch th einsides of th ewindows with
hard objects, e.g .anice scrape rorring. There
is otherwise ariskofd amaging th ewindows.
!Clean th ewaterdrainage channels of the
windshield and th erear window at regular
intervals. Deposits suchasl eaves, petals and
pollenm ay undercertain circumstances pre- ven
twate rfromd raining away. This can lead
to corrosion damagea nd damagetoelec-
tronic components.
XClean th einside and outside of th ewindows
withad amp cloth and acleanin gproduct that
is recommended and approved by Mercedes-
Benz.
Cleaning wiper blades
GWARNING
You coul dbecome trapped by th ewindshield
wipersift heys tart moving while cleanin gthe
windshield or wiper blades.T hereisarisko f
injury.
Always switch off th ewindshield wipersa nd
th ei gnition before cleanin gthe windshield or
wiper blades.
!Do no tpull th ewiper blade. Otherwise, the
wiper blade coul dbedamaged.
!Do notclean wiper blades to ooften and do
no trub them to ohard .Otherwise, th egraph-
ite coatin gcoul dbed amaged. This could
caus ewiper noise.
!Holdthe wiper arm securely when folding
back .The windshield coul dbedamaged if the
wiper arm smacks against it suddenly.
XFol dthe windshield wiper arm saway from the
windshield (Ypage 116).
XCarefully clean th ewiper blades withad amp
cloth.
XFol dthe windshield wiper arm sback again
before switching on th eignition.
Cleaning th eexterior lighting
!Only use cleanin gagents or cleanin gcloths
whicha re suitable for plastic light lenses.
Unsuitable cleanin gagents or cleanin gcloths
coul dscratch or damag ethe plastic light len-
ses.
XClean th eplastic lenses of th eexteri or light-
ing usingaw et sponge and amild cleaning
agent, e.g .Mercedes-Ben zcar shampoo or
cleanin gcloths.
Care295
Maintenance and care
Z
Page 298 of 354

Cleaning themirror turn signals
!Only use cleanin gagents or cleanin gcloths
that are suitable for plastic lenses.U nsuitable
cleanin gagents or cleanin gcloth scould
scratch or damag ethe plastic lenses of the
mirror tur nsignals.
XClean th eplastic lenses of th emirror tur nsig-
nals in th eexteri or mirror housing usingaw et
sponge and mild cleanin gagent, e.g.
Mercedes-Ben zcar shampoo or cleaning
cloths.
Cleaning th esensors
!If you clean th esensorsw ithapower
washer, mak esure that you keep adistance
of at least 11.8 in (30 cm)between the vehicl e
and th epower washer nozzle. Information
about th ecorrec tdistanc eisavailabl efrom
th ee quipment manufacturer.
XClean sensors :of th edriving systems with
water, car shampoo and asoftc loth.
Cleaning th erearv iew camera and 360°
camera
!Do no tclean th ecamera lensa nd thearea
aroun dthe rear view camera or 360°camera
with ahigh-pressurew aterjet.
XMakes ure that th evehicle is stationar yand
that th eSmartKey is in position 2in th eigni-
tio nlock.
XOpen th ecamera cover for cleanin gvia the
multimedia system (see th eseparate operat-
ing instructions).
XTo clean th ecamera: use clean wate rand a
softc loth to clean camera lens :.
360°camera: if you driveatspeeds above
20 mph (30 km/h) or with th eSma rtKey in posi-
tion 0or 1in th eignition lock, th ecover of the
360° camera closes automatically.
Cleaning th eexhaust pipes
GWARNING
The exhaust tail pipe and tail pipe trim can
become ver yhot.Ify ou com eintoc ontact
with these part softhevehicle ,you coul dburn
yourself. Thereisar isk of injury.
Always be particularly careful aroun dthe
exhaust tail pipe and th etail pipe trim. Allow
these component stocooldown before touch-
ing them.
!Do no tclean th eexhaust pipe with acid-
based cleanin gagents ,suchasb athroom
cleaner or wheel cleaner.
!Mercedes-AM Gvehicle swith black exhaust
pipes:t heblack-chrome tailpipe finishers
shouldn otbe polished with achrom epolish.
They will otherwise lose their black sheen. For
optimal care, th efaceplates shouldber ubbed
with alightly oiled cloth after everyc ar wash.
Commercially availabl eengine and car eoils
are suitable for this.
For heavier soiling, you can apply afinep aint-
work polishw itham icrofiber cloth .Remove
th ee xcess polishr esidue after polishing.
296Care
Maintenance and care
Page 299 of 354

Impurities combined with the effects of road grit
and corrosive environmental factors may causeflash rust to form on the surface. You can
restore the originals hine of the exhaust pipe by
cleaning it regularly ,especially in winter and
after washing.
XClean the exhaust pipe with acare product
tested and approved by Mercedes-Benz.
Interio rcare
Cleaning the display
!For cleaning, do not use any of the following:
Ralcohol-base dthinner or gasoline
Rabrasive cleaning agents
Rcommercially-availabl ehousehold cleaning
agents
These may damage the display surface. Do
not put pressure on the display surface when cleaning. This could leadtoi rreparabledam-
age to the display.
XBefore cleaning the display, make sure that it
is switched off and has cooled down.
XClean the display surface using acommer-
ciallya vailable microfiber cloth and TFT/LCD
display cleaner.
XDry the display surface using adry microfiber
cloth.
Cleaning the plastic trim
GWARNING
Care products and cleaning agents containing solvents cause surfaces in the cockpit to
become porous. As aresult, plastic parts may
come loose in the event of air bag deploy-
ment. There is arisk of injury.
Do not use any care products and cleaning
agents to clean the cockpit.
!Do not affix the following to plastic surfaces:
Rstickers
Rfilms
Rscented oil bottles or similar items
You can otherwise damage the plastic.
!Do not allow cosmetics, insect repellent or
sunscreen to come into contact with the plas- tic trim. This maintains the high-quality look of
the surfaces.
XWipe the plastic trim with
adamp, lint-free
cloth, e.g. amicrofiber cloth.
XHeavy soiling: use care and cleaning prod-
ucts recommended and approved by
Mercedes-Benz.
The surface may change color temporarily.
Wai tuntil the surface is dry again.
Cleaning the steering whee land gear or
selecto rlever
XThoroughly wipew ithadamp cloth or use
leather care agents that have been recom-
mended and approved by Mercedes-Benz.
Cleaning genuine wood and trim ele-
ments
!Do not use solvent-based cleaning agents
such as tar remover, wheel cleaners, polishes
or waxes. There is otherwise arisk of damag-
ing the surface.
!Do not use chrome polish on trim pieces.
The trim pieces have achrome look but are
mostly made of anodized aluminum and can
lose their shine if chrome polish is used .Use
ad amp, lint-free cloth instead when cleaning
the trim pieces.
If the chrome-plated trim pieces are very
dirty, you can use achrome polish. If you are
unsure as to whether the trim pieces are
chrome-plated or not, consult an authorized
Mercedes-Benz Center.
XWipe the wooden trim and trim pieces with a
damp, lint-free cloth, e.g. amicrofiber cloth.
XTrim elements with piano black finish:
clean with asoft, damp cloth and acommer-
ciallya vailable soap solution.
XHeavy soiling: use care and cleaning prod-
ucts recommended and approved by
Mercedes-Benz.
Cleaning the seat covers
General notes
!Do not use amicrofiber cloth to clean covers
made out of real leather, artificia lleather or
DINAMICA. If used often, these can damage
the cover.
Care297
Maintenancea nd care
Z
Page 300 of 354

Note that regular care is essential to ensure that
the appearance and comfort of the covers is
retained over time.
Genuine leather seat covers
!To retain the natural appearance of the
leather, observe the following cleaning
instructions:
RClea ngenuine leather covers carefully with
ad amp cloth and then wipe the covers
down with adry cloth.
RMake sure that the leather does not
become soaked. It may otherwise become
rough and cracked.
ROnly use leather care agents that have
been tested and approve dbyMercedes-
Benz. You can obtain these from aqualified
specialist workshop.
Leather is anatural product.
It exhibits natural surface characteristics, for
example:
Rdifferences in the texture
Rmarks caused by growth and injury
Rslight nuances of color
These are characteristics of leather and not
material defects.
Seat covers of other materials
!Observe the following when cleaning:
Rclean artificia lleather covers with acloth
moistened with asolutio ncontaining 1%
detergent (e.g. dish washing liquid).
Rclean cloth covers with amicrofiber cloth
moistened with asolutio ncontaining 1%
detergent (e.g. dish washing liquid). Rub
carefully and always wipe entire seat sec-
tions to avoid leaving visiblel ines. Leave
the seat to dry afterwards. Cleaning results
depend on the type of dirt and how long it
has been there.
Rclean DINAMICA covers with adamp cloth.
Make sure that you wipe entire seat sec-
tions to avoid leaving visiblel ines.
Cleaning the seat belts
GWARNING
Seat belts can become severely weakened if
bleached or dyed .This could cause the seat
belts to tear or fail, for instance, in the event of
an accident. This poses an increased risk of
injury or fatal injury.
Never bleach or dye the seat belts.
!Do not clean the seat belts using chemical
cleaning agents. Do not dry the seat belts by
heating at temperatures above 176 ‡(80 †)
or in direct sunlight.
XUse clean, lukewarm water and soaps olution.
Cleaning the headliner and carpets
XHeadliner:if it is very dirty ,use asoft brus hor
dry shampoo.
XCarpets: use the carpe tand textile cleaning
agents recommended and approved by
Mercedes-Benz.
298Care
Maintenancea nd care