display MERCEDES-BENZ C-Class SEDAN 2017 W205 Comand Manual

lane recommendations with a lower boundary
line. Highway information
Display mode Requirement: the
Highway Information
Highway Information map
content must be enabled (Y page 83).
While driving on the highway, gas stations, rest
stops, rest areas and highway exits are dis-
played along with their immediate distances
from the current vehicle position.
Calling up the selection mode X
When highway information is displayed, slide
9 the controller.
The marker is on the highway information. The
associated position is highlighted on the map.
X To select the desired rest stop/freeway
exit:
turn and press the controller.
The available POIs are displayed. Starting route guidance to a POI X
To select a POI: turn the controller and press
to confirm.
The POI details are displayed.
You can perform the following functions:
R Store in the address book (Y page 80)
R View on the map (Y page 84)
R Call if a phone is connected and a phone
number is available (Y page 98)
R Select for route guidance and calculate a
route to it (Y page 59)
Using the traffic jam function Highway information enables the use of the traf-
fic jam function. The remaining route on the
highway in this case is blocked in the direction of
travel from the selected exit.
X To select Detour Detour: turn and press the control-
ler.
The traffic jam function appears
(Y page 76). Route guidance
73Navigation Z

Route information
Destination information X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Route
Route: turn and press the controller.
X Select Destination Information
Destination Information.
The destination and existing intermediate
destinations are displayed with distances,
travel time and arrival time.
X To select destination or intermediate des-
tination: turn and press the controller.
The address appears.
X Select Save
Save .
The destination or intermediate destination
can be saved as:
R a navigable address book contact
R a home address
X To call up the map, select Map
Map.
X Move the map, change the map scale and
select the destination or the intermediate
destination (Y page 64).
X To call the destination or intermediate desti-
nation, select Call
Call .
If a phone is connected and a phone number
is available, the multimedia system switches
to the telephone function. Taking an alternative route If the
Calculate Calculate Alternative
Alternative Routes
Routessetting
is activated 0073, different routes will be offered
each time a route is calculated (Y page 55).
You can call up alternative routes to the current
route.
Routes 1, 2 and 4 are displayed with a dark blue line.
Route 3 is the most economic route and is dis-
played with a green line.
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Route
Route: turn and press the controller.
X Select Alternative Route Alternative Route.
Route 1 is shown.
X To display additional routes: select Next
Nextor
Previous
Previous .
X To start a new route guidance: select
Start
Start.
Route list X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Route
Route: turn and press the controller.
X Select Route List
Route List .
The route list shows the next change of direc-
tion and the immediate distances from the
current vehicle position.
X To display additional route sections: turn
the controller.
The position of the change of direction that
belongs to the respective route section is
indicated on the map with a cross. Route guidance
75Navigation Z

Where am I?
X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Position
Position: turn and press the con-
troller.
X Select Where am I?
Where am I?.
The street you are currently on and the pre-
vious and next intersections are displayed. Traffic jam function
X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Route
Route: turn and press the controller.
X Select Detour
Detour.
X To specify the start of the traffic jam sec-
tion: select Beginning
Beginning.
The next possible traffic jam section starting
point is marked.
X Turn the controller.
The marking moves along the route to the
next starting position.
X Press the controller.
The start of the traffic jam is set. X
To specify the end of a traffic jam section:
select End
End.
The next possible traffic jam section end point is marked.
X Turn the controller.
The marking moves along the route to the
next end position.
X Press the controller.
The end of the traffic jam is determined.
X To calculate the detour: selectStart Start. Off-road
General notes The navigation system may guide you to off-road
routes that your vehicle cannot drive on without
causing damage to the tires or wheels or the
vehicle itself. It is the driver’s sole responsibility to determine the suitability of the route. The
condition of the off-road routes may vary. The
navigability of off-road routes may be influenced
by various factors such as time of day, time of
year and prevailing weather conditions. The nav-
igation system cannot judge these factors or
take them into account for route guidance.
Route guidance to an off-road destina-
tion The multimedia system can guide you to desti-
nations which are within the area of the digital
map, but which are not themselves on the map.
These destinations are known as off-road des-
tinations, which you can enter using the map, for example. The multimedia system guides you for
as long as possible with navigation announce-
ments and displays on roads known to the sys-
tem.
If the vehicle reaches an area which is not part of the digital map, the display appears as a split-
screen view. On the right, an arrow appears that
points to the off-road destination. You hear the
announcement: "Please follow the arrow on the display". As the vehicle approaches the desti-
nation, you will see a display to this effect.
Route guidance from an off-road loca-
tion to a destination Off-road location: the vehicle's position is on the
digital map, but the map does not contain any
information about that location. The multimedia 76
Route guidanceNavigation

system is able to guide you to a destination even
from an off-road location.
At the start of route guidance, you will see the
Road Not Mapped
Road Not Mapped message, an arrow and the
distance to the destination. The arrow shows
the compass heading to the actual destination.
As soon as the vehicle is back on a road known
to the system, route guidance continues in the
usual way.
Off-road during route guidance Due to road construction, for example, there
may be differences between the data on the
digital map and the actual course of the road.
In such cases, the system will temporarily be
unable to locate the vehicle position on the dig- ital map. The vehicle is therefore in an off-road
position.
In the display, you will then see the Road Not
Road Not
Mapped Mapped message, an arrow and the distance to
the destination. The direction arrow shows the
compass heading to the destination.
As soon as the system can assign the vehicle
position to the map again, route guidance con-
tinues in the usual way. Real-time traffic reports
Prerequisites
This function is currently not available for Can-
ada.
In order to receive real-time traffic reports via
satellite radio, you need to subscribe to SIRIUS
XM Satellite Radio Traffic Message Service.
Further information on satellite radio
(Y page 136).
The multimedia system can receive traffic
reports via satellite radio and take account of
these for route guidance in the navigation sys-
tem. Received traffic reports are displayed on
the map either as text or as symbols. Real-time traffic reports on the map
The multimedia system can show certain traffic
incidents on the map with symbols (type of inci-
dent) and colored lines (extent). Traffic reports
are shown on the map at scales of 1/32 mi to
20 mi.
When 0043is displayed, traffic reports can be
received or traffic reports are available. If it is
not displayed, no reception is possible.
X To hide the menu: slide5and press the
controller.
The map can be seen in the full-screen dis-
play.
X To set the map scale: turn the controller
until the desired map scale is selected. 0043
Traffic jam on the route
0044 Slow-moving traffic on the route
0087 Road blocked
0085 Traffic jam
0083 Traffic warning
0084 Dashed red and white line delimiting the
traffic warning
006B Road block (crosses along the affected
road)
006C Slow-moving traffic (orange line along the
affected route)
006D Traffic jam (red line along the affected route) Real-time traffic reports
77Navigation Z

Displaying real-time traffic reports
Starting a search for traffic reports X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Traffic
Traffic: turn and press the con-
troller.
If satellite signals cannot be received or there are no traffic reports, you will see a message
to this effect.
X To close the report: press the controller.
Traffic symbol information 0043
Affected roads with indication of direction
0044 Symbol for report type, e.g. traffic flow mes-
sage
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Traffic Traffic: turn and press the con-
troller.
X To select Traffic Symbol Information
Traffic Symbol Information:
turn and press the controller.
The map appears and shows the available
traffic information as icons. The first traffic
information is highlighted. X
To highlight additional traffic symbols, select
Next
Next orPrevious Previous.
X To move the map: selectMap
Map.
You can move the map to enable further traf-
fic information to be displayed. You can have the traffic report relevant to a traf-
fic icon shown.
X To select Details
Details: turn and press the con-
troller.
The report shows the following information:
R State/province, road and display of the affec-
ted direction
R Section of the road to which the traffic report
applies
R Traffic icon and traffic report
X To close the detailed display: press the
0038 button.
Displaying reports on the route The function is only available while route guid-
ance is active. It shows the available traffic
reports affecting the current route.
If there are no reports for the route or the func- tion is not supported in the selected language:
the Messages Messages On
OnRoute
Route menu item is gray and
cannot be selected. 78
Real-time traffic
reportsNavigation

X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Traffic
Traffic: turn and press the con-
troller.
X To select Messages On Route
Messages On Route: turn and
press the controller.
The traffic report window appears. Several
traffic reports may be available for the calcu-
lated route, marked for example by 1/3.
The report shows the following information:
R State/province, road and display of the
affected direction
R Section of the road to which the traffic
report applies
R Traffic icon and traffic report
X To display the next/previous traffic
report: turn the controller.
X To close the display: press the0038button.
Displaying all traffic reports X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Traffic
Traffic: turn and press the con-
troller.
X To select All Messages All Messages: turn and press the
controller.
A list is shown containing all roads, areas or
regions affected by traffic reports. Roads,
areas or regions not on the route also appear in the list.
X To select the road, area or region: turn the
controller and press to confirm.
The traffic report is displayed (Y page 78).
There may be several traffic reports for the
affected road.
X To close the display: press the0038button. Settings for the display on the map You can switch these displays on/off on the
map:
R Incidents
R Speed & Flow
R Free Flow
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Traffic Traffic: turn and press the con-
troller.
X To select Traffic Information On Map
Traffic Information On Map :
turn and press the controller.
X Select Incidents
Incidents ,Speed & Flow
Speed & Flow orFree
Free
Flow
Flow.
The display is on 0073or off 0053. Reading out traffic reports on the
route
Introduction The text reader function is only available while
route guidance is active. It reads out traffic
reports affecting the current route.
You can select from the following text reader
properties:
R Language (Y page 41)
R Text reader speed (Y page 38)
You can start the text reader function manually
or set it to automatic.
Starting the text reader function man-
ually X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Traffic Traffic: turn and press the con-
troller.
X Select Read
Read Out
OutAll
AllMessages
Messages on
onRoute
Route .
The multimedia system reads out the reports in sequential order. Real-time traffic reports
79Navigation Z

If there are no reports for the route, the
Read
Read
Out All Messages on Route
Out All Messages on Route menu item is
gray and cannot be selected.
X To cancel the read-aloud function:
selectCancel Read-Aloud Function Cancel Read-Aloud Function.
The multimedia system reads the current
report aloud and then exits the read-aloud
function.
Automatic text reader function X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Traffic
Traffic: turn and press the con-
troller.
X Select Read Traffic Announcements
Read Traffic Announcements
Automatically Automatically.
Depending on the previous state, switch the
option on 0073or off 0053. Recalculating the route dynamically
The Dynamic Dynamic Traffic
TrafficRoute
Routeroute type takes
into account all of the traffic reports it receives
for the current route when calculating the route
(Y page 55).
If you have selected Dynamic Traffic Route Dynamic Traffic Route
as the route type, the multimedia system guides
you to your destination along the updated route. Storing destinations
General notes
If a route to a destination has been calculated,
the multimedia system saves the destination to the last destinations memory. If the memory is
full, the multimedia system overwrites the old-
est destination. When you save the current vehi-
cle position or a crosshair position, this position is stored in the "Last destinations" memory.
You can save destinations permanently in the
address book and on an SD card. For example,
you can save a destination as your home
address immediately after entering the address
(Y page 58).
Requirements: the SD card has the FAT data
system format (e.g. FAT32). Storing the destination in the address
book The example shows a POI.
X To select Save Save: turn and press the controller.
A menu appears.
X New contact: selectAs New Contact
As New Contact.
If the address book already contains con-
tacts, the entry Add
Addto
toContact
Contact is also avail-
able.
X Select Not Classified
Not Classified, Home
HomeorWork
Work.
An input menu shows the destination
address.
X Enter a surname and first name. Character
entry (Y page 30).
X To select OK OK: turn and press the controller.
The Saving Successful
Saving Successful message appears.
The destination address is saved in the
address book as a navigable contact.
X To add to a contact: selectAdd to Con‐ Add to Con‐
tact
tact.
The address book appears.
X Search for a contact (Y page 104).
X Press the controller.
The Saving Successful Saving Successful message appears.
The destination address is allocated to a con-
tact in the address book.
Telephone numbers are not transferred to the
telephone number fields of the address book.
After selecting the destination address from
the address book for navigation, the associ-
ated telephone number will be displayed.
If the contact already has two destination
addresses, a prompt will appear asking if a
destination address should be overwritten.
X Select Yes
Yes orNo No.
If you select Yes
Yes, a list showing both destina-
tion addresses appears. 80
Storing destinationsNavigation

X
To select the destination address: turn and
press the controller.
The destination address is overwritten.
X To save as "My address" selectAs "My
As "My
Address" Address".
The destination is saved as your home
address. Saving a destination to an SD card
X Insert the SD memory card (Y page 145).
X Select a POI, for example (Y page 61).
X To select Save Save: turn and press the controller.
A menu appears.
X Select To Memory Card
To Memory Card.
If no destination has been saved yet on the SD
card, an input menu will appear.
or X Select Not
NotClassified
Classified or, if available, select
a category that you have created yourself.
An input menu appears.
X Enter a new name and a new category for the
destination in the input menu if required.
Character entry (Y page 31).
X Select OK OK.
The Saving Successful
Saving Successful message appears.
The destination is saved to the SD card. Saving the current vehicle position
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Position
Position: turn and press the con-
troller.
X Select Save
Save.
The current vehicle position is saved in "Last
destinations". Saving the crosshair position
X To switch to navigation mode: press the
00BE button.
X To display the crosshair: press the control-
ler.
X Move the map to the desired position
(Y page 54).
X To show the menu: press the controller. X
To select Position
Position: turn and press the con-
troller.
X Select Save
Save.
The crosshair position is saved in the last des- tinations. Editing the last destinations
X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Destination
Destination : turn and press the
controller.
X Select From Previous Destinations
From Previous Destinations.
The "Last destinations" memory appears.
X To save the destination: select the destina-
tion.
The destination address appears.
X Store the destination in the address book
(Y page 80).
X Save the destination to the SD card
(Y page 81).
X To view the details: while in the "Last desti-
nations" memory, turn the controller and
highlight the entry.
X Slide 9the controller.
A menu appears.
X To select Details
Details: press the controller.
i The destination address can be changed if
desired. For instance, a different street or
house number can be selected.
X To delete one or all destinations: while in
the "Last destinations" memory, turn the con-
troller and highlight the entry.
X Slide 9the controller.
A menu appears. Storing destinations
81Navigation Z

X
To select Delete
DeleteorDelete All
Delete All: turn and
press the controller.
A prompt appears.
X Select Yes
Yes orNo No.
Selecting Yes
Yesdeletes the selected destina-
tion or all destinations. Map functions
General notes
Company logos displayed on the map are trade- marks of the respective companies and used
solely for the purpose of indicating the locations
of these companies. The use of such logos on
the map does not indicate approval of, support
of or advertising by these companies for the
navigation system itself.
i Alternatively, you can carry out this opera-
tion using the touchpad (Y page 24).Map settings
Setting the map scale Requirement: the map is in full screen mode, the
menu is faded out (Y page 54).
The lower left-hand section of the map shows
the currently set map scale and compass nee-
dle.
Right-hand-drive vehicles: the currently set map
scale and compass needle are displayed in the
lower right-hand section of the map.
X To show the map in full screen mode: to
hide the menu, push the 0038button.
or
X Slide the controller to the center of the map
and press to confirm.
X To set the map scale: as soon as you turn the
controller, the scale bar appears on the bot-
tom of the display.
X Turn the controller until the needle points to
the desired map scale.
Once you are finished selecting a map scale,
the new map scale will be shown. Selecting map orientation
X
To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Options Options: turn and press the con-
troller.
X Select Map Orientation
Map Orientation .
The 003Bdot indicates the current setting.
X Turn and press the controller.
The map orientation is set. Change
map direc-
tion Explanation
North Up North Up 005B
The map view is displayed
so that north is always up. Heading Up
Heading Up ¤
The map view is aligned to
the direction of travel. The
direction of travel is always at
the top; the red tip of the sym-
bol points north. 3-D Map 3-D Map ¤
The map view is aligned to
the direction of travel. The
map displays a 3D oblique
view with elevation; the red tip
of the symbol points north. 82
Map functionsNavigation

Selecting POI symbols on the map
POIs can be displayed as symbols in the map
display. POIs include, for example, gas stations,
hotels and restaurants.
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Options
Options: turn and press the con-
troller.
X Select Map Content
Map Content.
X Select POI Symbols On Map
POI Symbols On Map.
The 003Bdot indicates the current setting.
X Turn and press the controller.
Default Symbols
Default Symbols shows symbols of prede-
fined categories in the map.
Custom Custom Symbols
Symbols allows symbols to be selec-
ted from other/all available categories.
X Turn and press the controller.
You have the option of selecting symbols to
be displayed 0073or not displayed 0053on the
map.
The list shows all symbols that are contained
on the digital map across all countries. How-
ever, not all points of interest are available in all countries. As a result, certain point of inter-
est symbols may not be displayed on the map, even if the symbol display is switched on.
Selecting text information on the map At the bottom of the display, you can specify
whether to display geo-coordinates or not to
display text information for the street you are
currently on.
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Options
Options: turn and press the con-
troller. X
Select Map Content Map Content.
X Select Text Information On Map
Text Information On Map.
The 003Bdot indicates the current setting.
X Turn and press the controller.
Current
Current Street
Streetshows the current street at
the bottom of the display.
Geo-coordinates Geo-coordinates shows the longitude and
latitude, elevation and number of satellites
received.
The elevation shown may deviate from the
actual elevation.
X Turn and press the controller.
Switching highway information on/off The following can be displayed when driving on
a highway:
R the nearest gas stations and rest stops
R rest areas and highway exits
and their present distances from the vehicle's
current position (Y page 73)
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Options Options: turn and press the con-
troller.
X Select Map Content
Map Content.
X Select Highway Information
Highway Information.
Switch the display in the map on 0073or off 0053.
Further information (Y page 73).
Displaying the next crossroads If route guidance is not active, the next cross-
roads can be displayed at the upper edge of the
display.
X To switch to navigation mode: press the
00BE button.
X To show the menu: slide6the controller.
X To select Options Options: turn and press the con-
troller.
X Select Map Content
Map Content.
X Select Next Intersecting Street
Next Intersecting Street.
Switch the display in the map on 0073or off 0053. Map functions
83Navigation Z