stop start MERCEDES-BENZ GL SUV 2012 User Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2012, Model line: GL SUV, Model: MERCEDES-BENZ GL SUV 2012Pages: 441, PDF Size: 10.66 MB
Page 98 of 441

Oper
ating the panorama sliding sun-
roof
Opening and closing Overhead control panel
:
To raise
; To open
= To close/lower
The panorama sliding sunroof can only be
operated when the roller sunblind is open
(Y page 96).
X Turn the key to position 1or 2in the ignition
lock.
X Press or pull the 2switch in the corre-
spondin gdirection.
i If you press the 2switch beyond the
point of resistance, an automatic opening/
closing process is started in the corre-
sponding direction. You can stop automatic
operation by pressing again.
The automatic opening featur eisavailable
onl yw hen the slidin gsunroof is closed.
Rain-closin gfeature If the key is in position
0in the ignition lock
or if it is removed, the panoram asliding sun-
roof closes automatically:
R if it start storain
R at extreme outside temperatures
R after six hours
R if there is amalfunction in the power supply The panorama sliding sunroof remains raised
at the rear in order to allow ventilation of the
vehicle interior.
i
If the panorama sliding sunroof is obstruc-
ted while being closed by the rain-closing
feature, it opens again slightly. The rain-
closing feature is then deactivated.
The panorama sliding sunroof does not close
if:
R it is raised at the rear.
R it is blocked.
R no rain is falling on the area of the wind-
screen being monitored by the rain sensor
(e.g. because the vehicle is under abridge
or in acarport). Operating the panorama sliding sun-
roof roller sunblinds
Important safet ynotes G
WARNING
Make sure that nobody can become trapped
as you open or close the roller sunblinds.
The roller sunblinds shield the vehicle interior
from sunlight. The two roller sunblinds can
only be opened and closed together when the
panoram asliding sunroof is closed. Slidin
gsunroof
95Openingand closing Z
Page 99 of 441

Opening and closing th
eroller sun-
blinds Overhead control panel
:
To open
; To open
= To close
X Turn the key to position 1or 2in the ignition
lock.
X Press or pull the 2switch in the corre-
sponding direction.
i If you press the 2switch beyond the
point of resistance, an automatic opening/
closing process is started in the corre-
sponding direction. You can stop automatic
operation by pressing again.
Resetting the panorama sliding sunroof
and the roller sunblinds !
If the panoram asliding sunroof and the
roller sunblind cannot be fully opened or
closed after resetting, contact aqualified
specialist workshop.
Reset the panorama sliding sunroof and the
roller sunblinds if the panorama sliding sun-
roof or the roller sunblinds do not move
smoothly.
X Turn the key to position 1or 2in the ignition
lock.
X Pull the 2switch repeatedly to the point
of resistance in the direction of arrow =
until the panorama sliding sunroof is fully
closed. X
Keep the 2switch pulled for an addi-
tional second.
X Pull the 2switch repeatedly to the point
of resistance in the direction of arrow =
until the roller sunblinds are fully closed.
X Keep the 2switch pulled for an addi-
tional second.
X Make sure that the panorama sliding sun-
roof (Y page 95) and the roller sunblinds
(Y page 96) can be fully opened again.
X If this is not the case, repeat the steps
above again. 96
Sliding sunroofOpenin
gand closing
Page 114 of 441

i
Further related subjects:
R EASY-ENT RY/EXIT feature
(Y page 111)
R storing setting s(Ypag e115) Ste
ering wheel heating
Switchin gon/off X
Make sure that the key is in position 2in
the ignition lock.
X To switch on/off: turn the lever in the
direction of arrow :or;.
Indicator lamp =lights up or goe sout.
Vehicles without KEYLESS-GO: when you
remove the key from the ignition lock, the
steering wheel heating is switched off.
Vehicles with KEYLESS-GO: when you switch
off the ignition and open the driver' sdoor, the
steerin gwheel heating is switched off.
Problems wit hthe steering whee lheat-
ing The steerin
gwheel heating has switched
itsel foff prematurely or cannot be switched
on. Th evehicle' selectrical system voltage is
too low because too many electrical consum-
ers are switched on.
X Switc hoff elect rical consumers that you do
not need, such as the rear window heating
or inte rior lighting. EASY-ENTRY/EXIT feature
Important safety notes G
WARNING
Make sur ethat nobody can becom etrapped
when you activate th eEASY-ENTRY/EXI Tfea-
ture.
If there is arisk of someon ebecomin gtrap-
ped, stop th eadjustment procedure. To halt
the procedure:
R press the steerin gcolum nadjustment but-
ton.
R briefly press one of the memory fun ction
position buttons.
The steerin gcolum nstops moving immedi-
ately.
Do not keep the memory function position
button pressed down, otherwise the memory
function will start and the steerin gwheel and
seat will begin to move.
Never leav echildren unsupervised in the vehi-
cle. They coul dopen the driver' sdoor and
thereby unin tentionally activate the EASY-
ENTRY feature and become trapped.
The EASY-ENTRY/EX ITfeature make sgetting
in and out of your vehicle easier.
You can activa teand deactivat ethe EASY-
ENTRY/ EXIT feature in th eon-board com-
puter (Y page285).
Positio nofthe steering whee lwhen the
EASY-ENTRY/EXIT feature is active Th
es teering whee ltilts upwards if you:
R remov ethe key from the ignition lock
R open the driver's door and KEYL ESS-GO is
in position 1
R ope nthe driver's door and the key is in
position 0or 1in the ignition lock
i The steerin gwheel only moves upwards if
it has not already reached the upper end
stop. Steering wheel
111Seats, steering whee land mirrors Z
Page 136 of 441

X
Firml ypress release knob :and pull the
wipe rblade upwards from the wiper arm in
the directio nofthe arrow.
Fitting th ewiper blades X
Position the new wiper blade in the retainer
on the wiper arm and slide it into place in
the opposite direction to the arrow.
The wiper blade audibly engages.
X Make sure that wiper blade is seated cor-
rectly.
X Fold the wiper arm back onto the wind-
screen.
Replacing the rear window wiper blade Removing the wiper blades
G
WARNING
The wiper arm could be set in motion and
injur eyou if the windscreen wiper sare
switched on.
Remove th ekey from the ignition lock before
replacing the wiper blade. X
Remov ethe key from the ignition lock.
X Fold wiper arm :away from the rea rwin-
dow until it engages.
X Position wiper blade ;atar ight angle to
wiper arm :.
X Hold wiper arm :and press wiper
blade ;in the direction of the arrow until
it releases.
X Remove wiper blade ;.
Fitting the wiper blade
X Place new wiper blade ;onto wiper
arm :.
X Hold wiper arm :and press wiper
blade ;in the opposite direction to the
arrow until it engages.
X Make sure that wiper blade ;is seated
correctly.
X Position wiper blade ;parallel to wiper
arm :.
X Fold wiper arm :back onto the rear win-
dow. Problems with the windscreen wipers
The windscreen wipers are obstructed X
For safety reasons, you should remov ethe
key from the ignition lock.
or
X Switc hoff th eengine using the Start/Stop
butto nand ope nthe driver's door.
X Remove the cause of the obstruction.
X Switc hthe windscreen wiper sback on.
The windscreen wipers are inoperative The windscreen wiper drive is malfunctioning.
X
Select another wiper spee donthe combi-
nation switch.
X Hav ethe windscreen wiper schecked at a
qualified specialist workshop. Windscreen wipers
133Lights and windscreen wipers Z
Page 162 of 441

boostin
geffect. Yo uwill require considerably
more effor ttosteer and brake. There is arisk
of an accident.
Do not switch off the ignition while driving. G
WARNING
If the parking brake has not been fully
released when driving, the parking brake can:
R overheat and cause afire
R lose its hold func tion.
There is arisk of fire and an accident .Release
the parking brak efully before driving off.
! Warm up the engine quickly. Do not use
the engine's full performance until it has
reached operating temperature.
Only set the automatic transmission to the
respective drive positions when the vehicle
is stationary.
Where possible, avoid spinning the drive
wheels when pulling away on slippery
roads. Othe rwise, you could damage the
drive train.
! AMG vehicles: at low engine oil temper-
atures (below +20 †), the maximum
engine speed is restricted in order to pro-
tec tthe engine. To protec tthe engin eand
maintain smoo thengine operation ,avoid
driving at full throttle when th eengine is
cold. Key positions
Key g
To remove the key
1 Power supply for some consumers, such
as the windscreen wipers
2 Ignition (power supply for all consumers)
and drive position
3 To start the engine
i If the key doe snot belong to the vehicle,
it can still be tur nedint he ignition lock.
However ,the ignition will not be switched
on. The engin ecannot be started.
KEYLESS-GO General notes
R
Do not keep the KEYLESS-GO key together
with:
- electronic devices, e.g. amobile phone
or anothe rkey
- metallic objects, e.g. coins or metal film
- metallic objects, e.g. ametal case
This can affect the fun ction of the key with
KEYL ESS-GO.
Do not keep the KEYLESS-GO key in the tem-
perature-controlled cup holder
(Y pag e347). Othe rwise, the KEYL ESS-GO
key will not be dete cted.
Vehicles with KEYLESS-GO are equipped with
ak ey featuri ngan integrated KEYLESS-GO
function and adetachable Start /Stopbutton. Driving
159Drivingand parking Z
Page 163 of 441

The Start/Stop button must be inser
tedint he
ignition lock and the key with the integrated
KEYL ESS-GO function must be in the vehicle.
Pressing the Start/Stop butto nseveral times
in succession corresponds to the different
key positions in the ignition lock. This is only
the case if you are not depressing the brake
pedal.
If you depress the brak epedal and press the
Start/Stop button ,the engin estart simmedi-
ately.
i Thee ngine can be switched off whil ethe
vehicle is in motion by pressing and holding
the Start/ Stop button for three seconds.
This func tion operates independently of the
ECO star t/stop automatic engine switch-
off func tion.
Key positions with KEYLESS-GO Switching on th
epower supply
X If Start/ Stop button :has not yet been
pressed, this corresponds to the key being
removed from the ignition.
X Press Start/Stop button :once.
The power supply is switched on. You can
now activa tethe windscreen wipers, for
example.
i The powe rsupply is switched off again if:
R the driver' sdoor is opened and
R you press Start/Stop button :twice
when in this position Switching on th
eignition
X Press Start/Stop button :twice.
The ignition is switched on.
i The power supply is switched off again if:
R the driver' sdoor is opened and
R you press Start/Stop button :once
when in this position
Removing th eStart/Stop button You can remove the Start/Stop butto
nfrom
th ei gnition lock and star tthe vehicle as nor-
ma lusing the key.
X Remove Start/ Stop button :from ignition
lock ;.
i You do not have to remove the Start/Stop
button from the ignition lock when you
leav ethe vehicle.
i It is only possible to switc hbetween KEY-
LE SS -GO mode and key operation whe nthe
transmission is in position P.
i When you inser tStart/St op button :
int oignition lock ;,the system needs
approximatel ytwo seconds' recognition
time. You can then use Start/ Stop but-
ton :. 160
DrivingDriving and pa
rking
Page 164 of 441

Sta
rting the engine
Impor tant safety notes G
WARNING
Combustion engines emi tpoisonous exhaust
gases such as carbon monoxide. Inhaling
these exhaust gases leads to poisoning. There
is ar isk of fatal injury. Therefore never leave
the engine running in enclosed spaces with-
out sufficient ventilation.
i Vehicles with apetrol engine: the cat-
alytic converter is preheate dfor up to
30second safter acold star t.The sound of
the engin emay change during this time.
Automatic transmission X
Shift the transmission to position
P(Y page 168).
The transmission position displ ay inthe
multifunction displa yshows
P(Y page 168).
i You can also star tthe engin ewhen the
transmission is in position N.
Sta rting procedur ewith the key X
To star tapetrol engine: turn the key to
position 3in the ignition lock
(Y page 159 )and releas eita ss oon as the
engin eisrunning.
X To star tadiesel engine: turn the key to
position 2in the ignition lock
(Y page 15 9).
The % preglow indicator lam pinthe
instrumen tcluster lights up.
X When the %preglow indicator lamp
goes out, tur nthe key to position
3(Y page 159) and release it as soon as the
engin eisrunning.
i You can start the engine without preglow
if the engine is warm. Usin
gKEYLESS-GO to star tthe en gine G
WARNING
Your vehicle can be started using avalid KEY-
LESS-GO key. For this reason, children should
never be left unsupervised in the vehicle.
Always take the key with you when leaving the
vehicle, even if you are only leaving it for a
short time.
X Depress the brake pedal and keep it
depressed.
X To star tapetrol engine: press the Start/
Stop button (Y page 159) once.
The engin estarts.
X To start adiesel engine: press the Start/
Stop button (Y page 159)once.
Preglow is activated and the engin estarts.
i The Start/Stop button can be used to
start the vehicle without insertin gthe key
int ot he ignition lock .The key must be in
the vehicle and the Star t/Stop butto nmust
be inserted in the ignition lock. This mode
for startin gthe engin eoperates independ-
ently of the ECO start /stop automatic
engine start function. Pulling away
Automatic transmission G
WARNING
If the engine speed is above the idling speed
and you engag etransmission position Dor
R,t he vehicle coul dpull away suddenly. There
is ar isk of an accident.
When engaging transmission position Dor R,
always firmly depress the brake pedal and do
not simultaneously accelerate.
X Depress the brake pedal and keep it
depressed.
X Shift the transmission to position Dor
R(Y page 167). Driving
161Driving and parking Z
Page 166 of 441

ECO start/stop function
Important safety notes G
WARNING
If th eengine is switched off automatically and
you exit the vehicle, the engine is restarted
automatically. The vehicle may begin moving.
There is arisk of accident and injury.
If you wish to exit the vehicle, always turn off
the ignition and secure the vehicle against
rolling away.
General notes :
ECO start/stop display
The ECO start/stop func tion switches the
engin eoff automatically if th evehicle stops
moving.
When pulling away again, the engine starts
automatically. The ECO start/stop function
thereby helps you to reduc ethe fuel con-
sumption and emissions of your vehicle.
Every tim eyou switc honthe engin eusing the
key or the Star t/Stop button, the ECO start/
sto pfunction is activated.
AMG vehicles: the ECO start/stop function
is only available in drive program C.
The system is operational when the ¤
symbol is shown in green in the multifunction
display.
AMG vehicles: the AMG menu in the multi-
function displa yadditionally shows the Stop/Star
tactive message.
If no tall condition sfor automatic engine
switch-of fare fulfill ed (Ypage 164), the
¤ symbol is shown in yellow in the multi-
function display. AMG vehicles:
the AMG menu in the multi-
function display additionally shows the Stop/ Star
tinactive message.
If th eECO start/stop function has been man-
uall ydeactivated (Y page 163) or if amal-
function has caused the system to be deac-
tivated, the ¤symbol is not displ ayed.
AMG vehicles: theStop/Start active or
Stop/Start inactive displa
ymessage
goes out in the AMG men uofthe multifunc-
tion display.
If the engin eisswitched off and the ¤
symbol is shown in green in the multifunction
display, the engine has been switched off
automatically .However, all vehicle systems
remain active.
Deactivating/activa ting th eECO start/
stop function ECO button
X
To switch off (except AMG vehicles):
press button :.
Indicator lamp ;on button :and the
¤ symbol in the multifunction display go
out.
X To switch on (except AMG vehicles):
press button :.
Indicator lamp ;lights up. If all conditions
for automatic engine switch-off
(Y page 164 )are fulfilled ,the ¤ symbol
is shown in gree ninthe multifunc tion dis-
play.
If not all conditions for automatic engine
switch-off ar efulfilled, the Driving
163Drivingand pa rking Z
Page 167 of 441

(
Y page 16 4)¤ symbol is shown in yel-
low in the multifu nction display .Ifthis is the
case ,the ECO star t/stop function is not
available.
X To switch of f(AMG vehicles): in program
C,p ressbutton :.
or
X Switc htod rive program Sor M
(Y page 170).
Indi cator lamp ;on button :and the
¤ symbol in the multifunction display go
out.
The Stop/Star tactive or
Stop/Start inactive message in th
eAMG men uinthe
multifunction displa ygoes out.
X To switch on (AM Gvehicles): press but-
ton :.
Indicator lamp ;lights up. If drive pro-
gram Sor Mis active, the automatic trans-
mission switches to drive program C.
If all conditions for automatic engine
switch-of f(Ypage 16 4)are fulfilled, the
¤ symbol is shown in green in the mul-
tifunction display. In addition, the Stop/Star
tactive message is show
ninthe
AMG men uinthe multifunction display.
If not all condition sfor automatic engine
switch-of f(Ypage 16 4)are fulfilled, the
¤ symbol is not shown. If this is the
case, the ECO start/stop function is not
available. In addition, the Stop/Startinactive message is shown in the AMG
menu in the multifunction display.
i If indicator lamp ;is off, the ECO start/
stop function has been deactivated man-
ually or as the result of amalfunction .The
engin ewill then not be switched off auto-
matically when the vehicle stops.
i Ever ytime you switch on the engine using
the key or the Star t/Stop button, the ECO
start/stop function is activated. Automatic engine switch-off If the vehicle is braked to
astandstill in Dor
N,t he ECO start/stop func tion switches off
the engin eautomatically.
The ECO start/stop function is operational
and the ¤symbol is displayed in green in
the multifunction displa yif:
R thei ndicato rlamp in the ECO button is lit
green
R none of the off-road programs are selected
R the vehicle is stationary
R the outside temperature is within the com-
fort range
R the engine is at normal operating temper-
ature
R the set temperature for the vehicle interior
has been reached
R the battery is sufficiently charged
R the system detects that the windscreen is
not misted up when the air-conditioning
system is switched on
R the bonnet is closed
R the driver' sdoor is closed and the driver's
seat belt is fastened
If not all condition sfor automatic engine
switch-of fare fulfilled ,the ¤ symbol is
shown in yellow.
AM Gvehicles: the AMG menu in the multi-
func tion display additionally shows the Stop/ Star
tinactive message.
i If yo ushift the transmission from Rto D,
the ECO start/stop func tion is available
again onc ethe ¤ symbol reappear sin
green in the multifunction display.
i All vehicles (except AM Gvehicles):
automatic engine switch-off can take place
am aximum of four times consecutively (ini-
tial stop, then three subsequent stops). The
¤ symbol is shown in yellow in the mul-
tifunction displ ayafter the engine has been
started automatically for the fourth time.
When the ¤symbol is shown in green 164
DrivingDriving and parking
Page 168 of 441

in the multifunction display, automatic
engin eswitch-of fisa gain possible.
i AMGvehicles: times which the engine
can be automatically switched off.
i You can also activat ethe HOL Dfunction
when the vehicle is stationary if the engine
has been switched off automatically. It is
then not necessary to continue depressing
the brak epedal during the automatic stop
phase. When you depress the accelerator
pedal, the engine star tsautomatically and
the braking effect of the HOLD function is
deactivated. Depress the accelerator pedal
gently, as the engine must be started first.
i During automatic engine switch-off ,the
climate con trol system only operates at a
reduced capacity. If you require full climate
con trol capacity, the ECO star t/stopfunc-
tion can be deactivated by pressing the
ECO button (Y page 163).
Automatic engin estart The engine is started automatically if:
R you switch off the ECO start/stop function
by pressing the ECO button
R you releas ethe brakes when in transmis-
sion position Dor N,w hen the HOL Dfunc-
tion is inactive
R you depres sthe accelerator pedal
R you engage reverse gear R
R you mov ethe transmission out of position
P
R you switc htodrive program Sor M(AMG
vehicles)
R yo us witch to an off-road program (except
AMG vehicles)
R you unfasten your seat belt or open the
driver's door
R the vehicle start storoll
R the brake system requires this
R the tempera turein the vehicle interior devi-
ates from the set range R
the system detect smoistur eont he wind-
screen when the air-conditionin gsystem is
switched on
R the battery's charge status is too low
i Shifting the transmission to position P
doe snot star tthe engine. Driving
165Driving and pa rking Z