rims MITSUBISHI 3000GT 1991 User Guide

51-16
EXTERIOR - Garnishes and Mouldings
GARNISHES AND MOULDINGS
M51RDAFREMOVAL AND INSTALLATION
13 Nm2.5Nm18FO174
Front deck garnish removal steps
1. Wiper arm assembly
2. Front deck garnish
Drip moulding and center pillar garnish removal
steps
Drip line weatherstrip(Refer to GROUP 42
-Door weatherstrip holderDrip Line Weatherstrip.)
3. Drip moulding
Quarter upper trim (Refer to GROUP
52A-Trims.)
4. Center pillar garnish
Adhesive tape:3M ATD Part No. 6382 or equivalentWindshield moulding removal steps
3. Drip moulding
5. Windshield moulding (Refer to
GROUP 42 -Windshield.)
Liftgate moulding removal
6.
Liftgate moulding (Refer to
GROUP 42 - Liftgate Glass.)
Quarter window moulding and glass
removal steps
4. Center pillar garnish
7. Quarter window moulding and
glass (Refer to GROUP42
-Quarter Window Glass.)
Side garnish removal
l * l *8. Sidegarnish
Rear panel garnish removal steps
Rear end trim
Rear side trim
3(Refer to GROUP
52A-Trims.)9. Rear combination light
10. Rear panel garnish
I
I
I
I
I1
~
:Ij ~
I
I1
I
I
L.JTSB Revision

51-20EXTERIOR - Aero Parts
AERO PARTSM5lXAA.J
REMOVAL AND INSTALLATION
25NmI:8 ft.lbs.
18FO179
@ Adhesive tape:3M ATD Part No. 6382 or equivalent
m Adhesive:3M ATD Part No. 8609 SUPER FASTURETHAN or equivalent
18FO251Side air dam removal steps
Front splash shield (Refer to GROUP 42
-Fender.)
Quarter trim (Refer to GROUP
52A-Trims.)
l * **1. Side air dam
Rear spoiler removal steps
Liftgate lower trim (Refer to GROUP 52A-Trims.)
2. Rear spoiler assembly
3. Center stay
4. High mounted stop light
TSB Revision

EXTERIOR - Aero Parts51-21
8
Side air dam removal steps
Front splash shield
(Refer to GROUP 42
- Fender.)
+I) l +1. Side airdamRear spoiler removal steps
Liftgate lower trim
(Refer to GROUP 52A-Trims.)2. Rear spoiler assembly
4. High mounted stop light
Front under cover panel, air dam link assembly
removal steps
5. Side cover panel
(L.H.)6. Front cover panel
7. Center cover panel
8. Front under cover panel
9. Lower plate
10. Upper plateI)* 11. Air dam link assembly
12. Under cover bracket
16FO252
16FOO53Active aero switch removal steps
13. Switch garnish C
14. Active aero switch
Active aero control unit removal steps
Rear side trim
(L.H.)(Refer to GROUP 52A-Trims.)15. Active exhaust control unit
16. Active aero control unitTSB Revision

EXTERIOR - Rear Wber and Washer51-35
REAR WIPER AND WASHERM51 KKAO
,/REMOVAL AND INSTALLATION
16FO104.lO
.llRemoval steps of wiper motor
1. Wiper blade
l *2. Wiper arm
3. SpacerRemoval steps of washer tube
Front pillar trim
(RH)Quarter trim (RH)
Liftgate lower trim (Refer to GROUP 52A -Quarter upper trim
(RH)Rear roof rail trim!R$$f$$ GRoUP 52A
Trims.)Rear side trim
(RH)i .
4. Wiper motor
l *8. Liftgate moulding, upper
9. Washer nozzle
Removal steps of washer tank
Rear end trim (Refer to GROUP
52A-Trims.)5. Cap
6. Washer tank
7. Washer motor
10. Tube and grommet assembly
11. Washer tube
1 TSB Revision

EXTERIOR - Rear Wiper and Washer
51-3718N007F
jINTERMITTENT WIPER RELAY
(1) Remove the quarter trim. (Refer to GROUP 52A
- Trims.)
(2) With the intermittent wiper relay connected to the wiring
harness connector, let the wiper operate intermittently and
check the voltage at terminal
0.WASHER MOTOR
(1) When the washer motor is inspected, make sure that it is
mounted on the washer tank and that the washer tank is
filled with water.
(2) Connect the battery as shown to check whether water is
pumped out.
SERVICE POINT OF INSTALLATION
2. INSTALLATION OF WIPER ARM
After assembling the wiper blade to the wiper arm, install
the wiper arm with its tip positioned along the ceramic part.
TSB Revision

INTERIORCONTENTSNWAA-A~
FLOOR CONSOLE*
____....._.........__._..._......_..._...... 11
REAR SEAT . .._._____..______....____.._.._._..___.._._____.....___....24
FRONT SEAT*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18SEAT BELT*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25IHEADLINING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17TRIMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12INSTRUMENT PANEL*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . .
i
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components, (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
2I

52A-12INTERIOR - Trims
19POO70
4Trim
19POO80
hornm
in.)
19POO8,
Pin
Trim
19POO8219POO80TRIMS
IM52UCW
TRIM CLIP REMOVAL/INSTALLATION
PROCE-DURES
The type of clip shown in the illustration, which is used for the
Eli ~
installation of instrument panel, should be removed and
installed by the following procedures described below.
REMOVAL
(1) Use a cross-tip (+) screwdriver to push inward the pin (at
the center of the trim clip) to a depth of about 2 mm
(.08
in.).(2) Pull the trim clip outward to remove it.
Caution
Do not push the pin inward more than necessary
because it may damage the grommet, or the pin may
fall in, if pushed too far.
INSTALLATION
(1) With the pin pulled out, insert the trim clip into the hole in
the trim.
(2) Push the pin inward until the pin’s head is flush with the
grommet.
(3) Check whether the trim is secure.
TSB Revision

INTERIOR - Trims52A-13EMOVAL AND INSTALLATION
19FOO33
Scuff plate
D-D1Quart&
upper trim19FOO2C
1B-B
Front piiar trimc-cIQuart&
upper trim
,wca*
Rear roof rail trim 1 igFoo22Cowl side trim removal steps
1. Scuff plate
2. Cowl side trim
Front pillar trim removal steps
4. Hanger bracket
5. Sash guide cover mounting bolt
6. Clip
7. Front pillar trimRear roof rail trim removal steps
8. Screw
10. Rear roof rail trim
Quarter upper trim removal steps
3. Quarter trim (Refer to
P.52A-14.)48: ;;;;anger9. Quarter upper trim
1 TSB Revision
NOTE(1) @: Location of metallic clip(2) c: Location of resin clip(3)* indicates trim clip. (Refer to P.52A-12.)(4)For door trim,. refer to GROUP 42 - Door TrimandWaterproof Film.
I

52A-14
INTERIOR - Trims
Scuff plate
19FOO46
33 ftlbs.19FOl60
Quarter trim removal steps
** ** 11. Rear seat
12. Shelf cover assembly
13. Shelf catcher
14. Cover
15. Garnish19. Rear seat belt anchor plate mounting bolt
20. Screw
21. Quarter trim
22. Rear side trim (Refer to
P.52A-15.)23. Quarter trim bracket
16. Sash guide cover mounting bolt
17. Front seat belt anchor plate mounting bolt
18. Retractor cover
NOTE*: Location of resin clipSERVICE POINT OF REMOVAL
11. REMOVAL OF REAR SEAT
With the lever pulled forward, raise the seat cushion to
remove it.
TSB Revision

INTERIOR - Trims52A-15

ISERVICE POINT OF INSTALLATION
11. INSTALLATION OF REAR SEAT
(1) Fit the seat cushion attachment wire under the seat-back positively.
(2) Pass the rear seat belt buckles through the. seat
cushion.
(3) Insert the lock plate of seat cushion in the hole provided
in the floor positively.
4-A{-
Rear endtrimB-Br-Rear side trim, rear end trim removal steps
I. Luggage compartment floor box (R.H.)2. Luggage compartment floor box (L.H.)9. Luggage compartment light connector con-
nection_ -10. Hear side trim
NOTE(1) @ : Location of metallic clip(2) * : Location of resin clip 3. Lid
(R.H.)4. Lid (L.H.)5. Rear end trim
6. Screws
7. Floor mat mounting clip
8. High floor center board
1 TSB Revision