brake sensor MITSUBISHI 3000GT 1991 Owner's Manual

FRONT SUSPENSION - Strut Assembly33A-5
STRUT ASSEMBLY
IREMOVAL AND INSTALLATION
‘=Il Adjustment of Wheel Alignment
M33lA- *
6
45 Nm
2
33 ft.lbs.4!
AI$
c3liI7 // ;I jI ’II ;/ ~I: /I /j j
1
-r11Ii /’ I--‘-
Removal steps
1. Brake hose tube clamo mountina bolt
2. Brake hose tube clam;-,3. Fr;;tSs;eed sensor clamp mountmg nut
4. Front speed sensor clamp
tABS>5. Strut lower mounting bolt
6. Strut upper mounting bolt
7. ECS connector

8. Cap
9. Strut assembly
1 TSB Revision

I,
ELECTRONIC CONTROL SUSPENSION (ECS) - ;;~i%:~ustment339-15
Item No.Check
PointCheck ConditionSoundness Determination Value
24
Check by actually operating
vehicle.Speedometer indication and
MUT indication coincide.
26
61
62
63
64Vehicle
speed
sensorstop
lightswitch
F.R.actuator
F.L.actuator
R.R.actuator
R.L.actuatorDepress brake pedal.
ON
Do not depress brake pedal.OFF
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD4. ACTUATOR CHECK
(I) Using the MUT, force-drive the actuator and fix the damping force changeover.
(2) Check service data (Item No. 61 through 64) to verify that the actuator has been force-driven.
NOTE
lAll of the four actuators in the shock absorbers are simultaneously changed over by forced drive.
lThe damping force changed over and fixed by forced drive is cleared by the following three conditions.1. Ignition switch OFF
2. Vehicle speed 3 km/h (1.9 mph) or more
3. MUT disconnected
Actuator Check List
Item No.Check Point
Check ConditionMUT Service Data Item
No. 61 - 64 Indicated
01Damping force SOFT
03Damping force MEDIUM
04Damping force HARD
Vehicle in stationary
conditionSOFT
MEDIUM
HARD
i
TSB Revision

33B-20 ELECTRONIC CONTROL SUSPENSION (ECS)-llwmtk Positkm .semor I stop tight switch I POriticm DetsctionSWitEh 1 DPmping Force changeover Acluatc., / EC3 Indii.ar l.igil*
THROTTLE POSITION SENSORM33ZKA6
INSPECTION AND ADJUSTMENTIRefer to GROUP 13
- Fuel System.‘lJ ’
STOP LIGHT SWITCHM33ZCAC
To remove or mount the stop light switch, refer to GROUP 35 -
Brake Pedal.
INSPECTIONRefer to GROUP 35
- Brake Pedal.
POSITION DETECTION SWITCH and
DAMPING FORCE CHANGEOVER
ACTUATORM33ZCAD
To remove or mount the position detection switch and dampingforce changeover actuator, refer to GROUP 33A
- Strut LJAssembly and GROUP 34
- Shock Absorber Assembly.
CautionThe position detection switch and damping force
changeover actuator are built into the shock absorber
assemblies of front and rear suspensions. Since they are ofthe non-disassembly type, remove or mount them in the
form of a strut assembly or shock absorber assembly.
ECS INDICATOR LIGHTM33ZLAB
To remove or mount the ECS indicator lights, refer to GROUP54
- Meters and Gauges.
TSB Revision

REAR SUSPENSION - Rear Suspension Assembly34-7
REAR SUSPENSION ASSEMBLYM34GA-A
L/
REMOVAL AND INSTALLATION
140- 160 Nm*IOI- 116ftlbs.
Removal steps
1. Shock absorber mounting nuts (upper)2. ECS connector (ECS)3. Cap4. Brake line clamp bolt5. Brake caliper mounting bolt6. Brake caliper assembly7. Brake disc
8. Parkina brake cable clamo bolt
(Refer to GROUP 15 - Exhaust Pipe and
l * l +9. ParkinG brake cable end ”(Refer to GROUP 36 - Parking Brake.)10. Rear speed sensor clamp bolt (ABS)11. ABS speed sensor (ABS)12. Trailing arm mounting bolt and nut*I)13. Crossmember mounting nut*I)14. Rear suspension assembly
NOTE*.indicates parts which should be temporarily tightened, and
then fully tightened with the vehicle in the unladencondition.
Post-installation Operationl Installation of the Main Muffler(Refer to GROUP 15 - Exhaust Pipe andMain Muffler.)l Check of Wheel Alignment(Refer.to P.34-5.)l Check of Parking Brake Lever Stroke(Refer to GROUP 36 -Service AdjustmentProcedures.)l Installation of the Absorber Lid to Rear Side Trim(Refer to GROUP 52A-Trims.)A12FOllO
SERVICE POINTS OF REMOVALM34GBAT
13. REMOVAL OF CROSSMEMBER MOUNTING NUT / 14.
REAR SUSPENSION ASSEMBLYSupport the crossmember with a transmission jack, then
remove the crossmember mounting nut and rear suspen-
sion assembly.
TSB Revision

REAR SUSPENSION - Trailing Arm34-11
TRAILING ARMM34TA-A
t’REMOVAL AND INSTALLATION
,’
i;
18
90Nm* A65ft.lbs.* 15Post-installation Operation
lCheck of Wheel Alignment
‘Refer to P.34-5.)>heck of Parking Brake Lever Stroke(Refer tn GROIJP 36 - Service Adiustment
r/A -50-60Nm36 - 43ftlbs.
(Refer to GROUP 35 -Service Adjustment
-160Nm* -- 116ft.lbs.*Removal steps
1. Brake caliper mounting bolt
2. Brake caliper
3. Brake line clamp bolt
4. Rear brake disc5. Hubcap
6. Wheel bearing nut
7. Hub assembly
8. Parking brake cable clamp bolt*I) I)*9. Parking brake cable end (Refer to GROUP 36- Parking Brake.)IO. Rear speed sensor clamp bolt (ABS)
11. ABS speed sensor (ABS)
36 - 43 ftlbs.12FOlll
12. Backing plateI)+ 13. Stabilizer link mounting nutl I)14. Self-locking nut
15. Shock absorber mounting bolt (upper)
l *16. Self-locking nutl *17. Self-locking nut
18. Trailing arm mounting bolt and nut
19. Trailing arm assembly
NOTE*:indicates parts which should be temporarily tightened, and
then fully tightened with the vehicle in the unladen
condition.
1 TSB Revision1

REAR SUSPENSION - Rear Axle Hub
REAR AXLE HUB34-17
REMOVAL AND INSTALLATION
50-60Nm36 - 43 ftlbs.
1
Removal steps
*I)I, Rear speed sensor a*2. Caliper assembly
3. Brake disc
4. Hubcap
l +5. Wheel bearing nut
6. Tongued washer
7. Rear hub assembly
*I)8. Rear rotor 9. Rear hub unit bearing
Caution
Rear hub unit bearing cannot be disassembled.
llN0018
14NOlO14N009E
SERVICE POINTS OF REMOVALM34MBAC
1.REMOVAL OF REAR SPEED SENSOR ABS>Caution
Be careful when handling the pole piece at the tip of the
speed sensor and the toothed edge of the rotor so as
not to damage them by striking against other parts.
2. REMOVAL OF CALIPER ASSEMBLY
Remove the caliper assembly and suspend it with a piece of
wire.
8. REMOVAL OF REAR ROTOR ABS>Caution
Care must be taken not to scratch or scar the rotor’s
toothed surface, and not to drop it.
If the rotor’s toothed surface is chipped or the rotor is
deformed, it might not be able to accurately sense the
wheel rotation speed and the system as a result might
not perform normally.
TSB Revision1

34-24REAR SUSPENSION - Rear Suspension Assembly
REAR SUSPENSION ASSEMBLY
REMOVAL AND INSTALLATION
M34GA-B
L
Rel
145 Nm9- 33 ftlbs.
1. Shock absorber mounting nuts (upper)*
2. ECS connector
*Pre-removal Operationl Removal of the Rear Side Trim Absorber Lid
(RefertoGROUP52A-Trims.)l Removal of the Center Exhaust Pipe and Main Muffler
(Refer to GROUP 15
- Exhaust Pipe and Main Muffler.)
5. Brake caliper*
1,50-60NmI36 - 43 ft.lbs.35 Nm
$8 Nm“?C,ILc. ashwez I,..“=.BP’----12Nm9 ftlbs.
15..e12FO1088. Pressure tube assembly to pipe assembly
connection
<4WS>9. Feed pipe assembly to suction hose connec-
tion
<4WS>10. Return pipe assembly to rubber hose con-
nection t4WS>11. Power cylinder tie rod coupling nut <4WS>*12. Differential carrier to propeller shaft coupling
bolt and nut
Post-installation Operationl installation of the Center Exhaust Pipe and Main Muffler
(Refer to GROUP 15
- Exhaust Pioe and Main Muffler.)
l Installation of the Rear Side Trim Absorber Lid
(Refer to GROUP
52A-Trims.)13. Center bearing mounting nut
14. Harness connector connection
CABS>*15. Parking brake cable and ABS sensor fixingl Refilling and Bleeding of the Power Steering System
(Refer to GROUP
37A- Service AdjustmentProcedures.)bolt
*16. Cable band*
17. Crossmember bracket*
18. Crossmember mounting nut (on differential
side)”19. Rear suspension assemblyl Checking Wheel Alignment
(Refer to P.34-23.)
l Bleeding of 4WS System
(Refer to GROUP 37B
- Service Adjustment
Procedures.)
l Operation Inspection of the 4WS System
(Refer to GROUP 37B - Service AdiustmentProcedures.)
NOTEParts marked with * are symmetrical.
,* Checking the Parking Brake Lever Stroke
(Refer to GROUP 36 -Service Adjustment
Procedures.)i
1 TSB RevisionI

34-30REAR SUSPENSION - Trailing Arm
TRAILING ARMM34TA-B1
REMOVAL AND INSTALLATIONN/A
$icJ
14 ft.lbs.T/C vehicles26-30Nm
50-60Nm936 - 43 ftlbs.\19 - 22 ft.lbs.
55-65Nm40 - 47ft.lbs.
200
- 240 Nm*145- 174ft.lbs.* I
P100 Nm
72 ft.lbs.
58 Nm’ <842 ft.lbs.Removal steps
*I)
*I)
+*+*
1. Rear brake caliper assembly
2. Rear brake disc
3. Drive shaft to companion flange mounting
bolt and nut
4. Self-locking nut
5. Companion flange
6. Rear axle shaft
7. Parking brake cable end
8. Parking brake cable clamp bolt
9. Rear speed sensor
(ABS)IO. Rear speed sensor cable and parking brake
cable bands (ABS)II. Dust shield
12. Self-locking nut (upper arm)
13. Self-locking nut (lower arm)
14. Tie rod end mounting
nut15. Trailing arm mounting bolt and nut
16. Rear shock absorber mounting bolt
17. Trailing arm
NOTEFor tightening points marked with *, first temporarily tighten
and then ground the vehicle to torque to specification where the
vehicle is empty.‘7
il 6’
12FOO89
Post-installation Operationl Check of Wheel Alignment
(Refer to P.34-23)l Check of Parking Brake Lever Stroke(Refer to GROUP 36 - Service Adiustment
TSB Revision

L,
SERVICE
BRAKES
CONTENTSM35AA..
ANTI-LOCK BRAKING SYSTEM TROUBLESHOOTING7Actuator Test Function
. . . . ..___..._____.__................................ I 2, 36Check Using Self Diagnosis Function __._.....,_._.._____........ 11, 28
Diagnosis Code Chart ..,,........,......_..................................,. 1 I, 28
How to Use the Troubleshooting Flow Chart
_____.___......._._.7Method of Clearing Diagnosis Code Memory._.,._...... 12, 30
Particular Phenomena of the Anti-lock Braking System
7Troubleshooting (ABS-AWD) ._______._.._...........................,... 26
Troubleshooting (ABS-FWD) ______.._._........_...........,.....,.....,....8
TroubleshootingMethods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
BRAKE LINE . . . . . . .._.......................................................................71
BRAKEPEDAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
ELECTRONIC CONTROL UNIT (ABS). . . . .._._..___..__._............93/
L
FRONT DISC BRAKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73G SENSOR (AWD-ABS)’
____.____.___.__._._.................,,......,.....,.... 92
HYDRAULIC UNIT (ABS) .___.._._._._.______.............,...,,..........~ .,_____86
MASTER CYLINDER AND BRAKE BOOSTER ..__.._____.._____67SPECIFICATIONS ._....._.___.....................................
REAR DISC BRAKE . . . . . . .._..._._.___................................................81
SERVICE ADJUSTMENT PROCEDURES..___........45Bleeding48
Brake Booster Operating Inspection.
46
Brake Drum Inside Diameter Check. . .56
BrakeFluidLevelSensor Check.46
Brake Lining and Brake Drum Connection Check56Brake
Linrng Thickness Check............................................Brake Pedal Inspection and Adjustment............................Check Valve Operation Check............................................Front Brake Disc Run-out Check........................................Front Brake Disc Run-out Correction................................Front Disc Brake Pad Check and Replacement................Inspection of Front Brake Disc Thickness........................Inspection of Hydraulic Unit................................................Inspectton of Power Relay....................................................Inspection of Valve Relay and Motor Relay (ABS)............Measurement of Wheel Speed Sensor Output Voltage
Proportioning Valve Function Test
....................................Rear Brake Disc Run-out Check........................................Rear Brake Disc Run-out Correction................................Rear Brake Disc Thickness Check....................................Rear Disc Brake Pad Check and Replacement................Remedy in Case of DischargedBattery............................56
45
46
52
53
48
5258
62
62
57
47
55
55
55
53
62
SPECIAL TOOLS ..__.......___..........................................................General Specifications
........................................................Lubricants............................................................................Sealants and Adhesives........................................................Service Specifications........................................................3
TROUBLESHOOTING............................................................5
WHEEL SPEED SENSOR (ABS)............................................88
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
i

35-2SERVICE BRAKES - Specifications
SPECIFICATIONSrvKwx.- -
GENERAL SPECIFICATIONSItems
FWDAWD
Master cylinderTypeTandem type
(with level sensor)Tandem type
(with level sensor)
I.D. mm (in.)
25.4
(1) or 26.9 (1 %s)*26.9 (1 '/l6)Brake boosterTypeVacuum type, tandemVacuum type, tandem
Effective dia. of power cylinder
mm (in.)
180 (7.0) + 205 (8.0) or203 (8.0) + 230 (9.0)
203 (8.0) + 230 (9.0)”
Boosting ratio
6.0 [at 247 N (54
Ibs.)] or7.0
[Brake pedal depressing force]
7.0 [at 261 N (58 Ibs.)]”[at 261 N (58 Ibs.)]Proportioning valve
Split point
MPa (psi)3.75 - 4.25 (533 - 604)3.75 - 4.25 (533 - 604)
Decompression ratio
0.370.37
Front brakesTypeFloating caliper, 2-piston,Rigid caliper, 4-piston,
ventilated disc (M-R57W)ventilated disc
(M-R66Z)Disc effective dia.mm (in.)
227
(9.0)249 (9.8)Disc thickness
mm (in.)24
(.94)30 (1.18)
Pad thicknessmm (in.)
16 (.63)15 l.59)
Wheel cylinder I.D.mm (in.)
42.8(1"/16)X240.4(1'g/32)x2 +42.8(1"/16)~2
Clearance adjustment
AutomaticAutomatic
Rear brakesTypeFloating caliper, l-piston,
ventilated disc
(M-R45V)Floating caliper, 1 -piston,
ventilated disc (M-R58V)Disc effective dia.mm (in.)
228
(9.0)237 (9.4)Disc thicknessmm (in.)
18 (.71)20 (.79)Pad thickness
mm (in.)15.5
(.61)15.5 (.61)Wheel cylinder I.D.mm (in.)
34.9 (13/8)38.1 (1%)
Clearance adjustmentAutomaticAutomatic
Rotor teeth
Front wheel side
4747Rear wheel side
4747Speed sensor
Magnet coil typeMagnet coil type
NOTE*:ABS
TSB Revision