length MITSUBISHI 3000GT 1991 Owner's Guide

37B-84-WHEEL STEERING SYSTEM (4WS) - Power Cylinder
(4) When the tie rod ends and the installation holes at the
trailing arm do not meet, loosen the tie rod end securing
nut, then adjust the length. The dust cover fastener clip
should be removed for this.
(5) The difference between the lengths of the left and
right’
Ljtie rods should be less than 1 mm
( ,039 in.).
NOTEThe threads of the tie rod ends may be used as a guide
for this.
DISASSEMBLY AND REASSEMBLYM37SE. -
::::::::::::;::: ::.
&
:::::y .:::5;:;. . . . . . . . .. .
11.
13G0070
Grease: Silicone greaseDisassembly steps
1. Nut**2. Tie rod end assembly3.Clip4.Wirel *5. Dust cover6.Bleedercaps
7.Bleeder screws8.Cylinder assembly
2
13A0128
13G0070
Rod13A025
SERVICE POINTS OF REASSEMBLYM37SHAA5. INSTALLATION OF DUST COVER
Apply the specified grease to the place indicated in the
illustration, then install the dust cover to the cylinder
assembly.
Specified grease: Silicone grease2. INSTALLATION OF TIE ROD END ASSEMBLY
Temporarily attach the tie rod end assembly to the cylinder
assembly at the place of dimension as illustrated.
NOTETo adjust the assembly dimensions of the tie rod end
assembly, remove the dust cover clip and rotate the rod.
TSB Revision

BODY - Window Glass
42-25
WINDOW GLASS
M42LAAL
/GENERAL
LiFor bonding of the windshield and liftgate glass, a single-liquid urethane adhesive is used.
ADHESIVE AND RESERVE ITEMS
Adhesive and Reserve ItemsApplicationsQuantityAdhesive
3M SUPER FAST URETHAN 8609
One cartridge
3M SUPER FAST URETHAN PRIMER 8608
As requiredReserve items
Wire (dia. x length)for cutting adhesiveFive pieces of wire
0.6 mm x 1 m
f.02 in. x 3.3 ft.)
Adhesive gun
for adhesive application
One
3M ATD Part No. 8906
for cleaning jointing surfaces
As required
Wiping rags
As required
Sealer
for prevention of water leaks and
gathering after adhesive applicationAs required
Glass holder
Two
Windshield moulding
One
(Service Part)
Window dam(Service Part)
As requiredTSB Revision

51-2
SPECIFICATIONSEXTERIOR
- Specifications
GENERAL SPECIFICATIONSMSlKB-
-\ IItems
Windshield wiper motorType
Speed control system
Braking system
rpm at load of 1 Nm (0.72
ft.lbs.)Low speed
High speed
Nominal torque
Nm (ft.lbs.)
Rear wiper motor
Motor type
Braking system
rpm at load of 0.6 Nm (0.43
ft.lbs.)Windshield wiper blade
Wiping angle
Driver’s side
Passenger’s side
Wiper blade length
mm (in.)
Driver’s side
Passenger’s side
Tear wiper blade
Wiping angle
Wiper blade lengthmm (in.)
Nindow washer motor and pump
Motor type
Pump type
Power consumption A
Time of continuous usesec.
With washer fluid
Empty operation
Nozzle jet pressure
kPa (psi)
Tank capacity
lit.
(qts.)
3ear window washer motor and pump
Motor type
Pump type
Power consumption A
Time of continuous use
sec.With washer fluid
Empty operation
Nozzle jet pressure
kPa (psi)
Tank capacity
lit. (qts.)Specifications
Ferrite-magnet type
Third brush system
Dynamic brake system
48
_+ 4
70
2 724(17)
Ferrite-magnet type
Dynamic braking system
38
+ 5
89”
91”
525 (20.7)
500 (19.7)87”
k 1.5”
550 (21.7)Direct current ferrite magnet type
Centrifugal type
3.8 or less
Max. 60
Max. 20
120 (17) or more
2.0
(2.1) or more
Direct current ferrite magnet type
Centrifugal type
3.8 or less
Max. 60
Max. 20
120 (17) or more
1.2 (1.3) or more
LJ
L/iTSB Revision

52A-8INTERIOR - Instrument Panel
INSTRUMENT PANELM52UAAT
For installation of the instrument panel, the bolts and screws described below are used. They are indicated by
symbols in the illustration.
,4x
16(.I6x.63)
5x16(.20x.63)4x
12(.I6x.47)
6x16(.24x.63)
II6 x 25 (.24 x .98)19N0001I
NOTED = Thread diameter
L = Effective thread length
TSB Revision
1