lock MITSUBISHI 3000GT 1991 Repair Manual

22-1
iv,MANUAL ~
TRANSAXLE
~
I
CONTENTSM22AA. -
MANUAL TRANSAXLE . . . . . . . . . . . .._...48INPUT SHAFT ASSEMBLY_..________.............: . . . . . . . . . . . . . . . . . . . . . . . . . .30
GENERAL INFORMATION....................................................48
SERVICE ADJUSTMENT PROCEDURES
............................51
Drive Shaft OilSealsReplacement....................................
52Speedometer Cable Replacement....................................
53Transfer Oil Seal Replacement............................................53Transmission Oil Level Inspection....................................51Transmission Oil Replacement............................................51
SHIFT LEVER ASSEMBLY....................................................
53
SPECIAL TOOLS........................................................................50
SPECIFICATIONS
....................................................................49
General Specifications........................................................49Lubricants............................................................................49
TRANSAXLE ASSEMBLY....................................................56,60
TRANSAXLE CONTROL*........................................................54
TRANSFER ASSEMBLY
........................................................59
MANUAL TRANSAXLE ....................2
CLUTCH HOUSING ASSEMBLY............................................46
DIFFERENTIAL ASSEMBLY
....................................................43
5TH SPEED SYNCHRONIZER ASSEMBLY
........................28
GENERAL INFORMATION
....................................................2INTERMEDIATE GEAR ASSEMBLY
....................................
OUTPUT SHAFT ASSEMBLY................................................
SERVICE ADJUSTMENT PROCEDURES............................
Drive Shaft Oil Seals Replacement....................................Speedometer CableReplacement....................................Transmission Oil Level Inspection....................................Transmisston Oil Replacement............................................
SHIFT LEVER ASSEMBLY....................................................
SHIFT RAILS AND FORKS....................................................
SPECIAL TOOLS........................................................................
SPECIFICATIONS....................................................................
General Specifications........................................................
Lubricants............................................................................
Sealants and Adhesives........................................................Service Specifications........................................................
Snap Ring (for Adjustment) and Spacer............................
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................
TRANSAXLE ASSEMBLY _____...._........__....................................
TRANSAXLE CONTROL*. . ..________.___.._ ..__._.__.__...............
36
41
9
10
9
9
9
13
42
6
3z
63
3
45
14
11TROUBLESHOOTING
___.._______._____.......,..................................8
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the
SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

22-6MANUAL TRANSAXLE - Specifications / Special Tools
LUBRICANTS
M22CD-A
Items
Manual transmission oil
Drive shaft oil seal lip
Specified lubricant
Hypoid gear oil, SAE
75W-90 or75W-85W conforming to APIclassification GL-4 or higherQuantity lit.
(qts)
2.3 (2.4)
As required
SEALANTS AND ADHESIVES
Items
Transaxle case - clutch housing mating surfaces
Transaxle case
- rear cover mating surfaces
Differential drive gear bolts
Bearing retainer screw (flush head screw)
Reverse brake cone mounting screw bolts
MUCE- _
Specified sealants and adhesives
Mitsubishi genuine part No. 997740 or equivalent
3M Stud Locking part No. 4170 or equivalent
Air breather
3M ATD part No. 8001 or equivalent
SPECIAL TOOLSM22DA-A.
nstallation of spring pin and lock
MD998323-01TSB Revision

MANUAL TRANSAXLE - Special Tools22-7
MD998348-0 1
Bearing remover
Removal of gears and bearings of input
shaft, intermediate gear and output shaft
andintermediate shaft lock nut
M
D998808-01Snap ring installerInstallation of input shaft rear snap ring
MD998822installer adapterInstallation of differential case bearings
iTSB Revision

22-16MANUAL TRANSAXLE - Transaxle Assembly
9. DISCONNECTION OF TRANSAXLE MOUNT
Raise transaxle assembly with a jack up to a level where
mount bracket no longer receives its weight and remove
transaxle mount insulator bolt.
CautionSupport the transaxle assembly with the jack so that
no localized force is applied to the assembly.
13. DISCONNECTION OF TIE ROD ENDUsing the special tool, disconnect the tie rod end from the
knuckle.
Caution1. Be sure to tie the cord of the special tool to the
nearby part.2. Loosen the nut but do not remove it.
14. DISCONNECTION OF LOWER ARM BALL JOINTUsing the special tool, disconnect the lower arm ball joint
from the knuckle.
Caution1. Be sure to tie the cord of the special tool to the
nearby part.2. Loosen the nut but do not remove it.
17. REMOVAL OF DRIVE SHAFT (LEFT SIDE), INNER SHAFT
ASSEMBLY(1) Remove the bearing bracket mounting bolts and insert
the pry bar between the bearing bracket and the
cylinder block.
(2) Remove drive shaft (left side) and inner shaft assembly
from transaxle assembly.
NOTERemove drive shaft and inner shaft assembly as an
assembly together with hub, knuckle, and other parts.
(3) Suspend the removed drive shaft (left side) and inner
shaft assembly with wire or something similar to
prevent it from sharply bending or turning at each joint.
TSB RevisionI

22-18MANUAL TRANSAXLE - Transaxle Assemblv
TRANSAXLE ASSEMBLYIM22ME.A
I
DISASSEMBLY AND REASSEMBLY
l5-22Nmdl
11 - 15 ftlbs.
-42 Nm
- 30 ftlbs.30-35 Nm
4.0 -5.5Nm
22
- 25 ft.lbs.lIll42.9 -3.9ftlbs.
/I18
J6140-160Nm1102-115ftlbs.
3-5Nm2.5 - 3.5 ftlbs.
11Disassembly steps
1.Bolt2.Rear cover3.Wave spring4.Screw bolts5. Reverse brake cone
6. Backup light switch
7.Gasket8.Poppet plug9.Poppet springIO. Poppet ball11.Bolt12. Speedometer driven gear assembly13.Air breather+* +* 14. Spring pin
*+ l * 15. Lock nut*+ l + 16. Lock nut17. 5th speed synchronizer assembly
18. 5th speed shift fork
19.Synchronizer ring20. 5th speed gear21.Needle bearing22. 5th speed intermediate gearTSB Revision

MANUAL TRANSAXLE - Transaxle Assemblv
;EALING AND ADHESION POINTS
Adhesive: 3M StudLocking Part No. 4170TFM0016
M ATD Part No. 8001
1 TSB RevisionI

MANUAL TRANSAXLE - Transaxle Assembly
Lock nut‘;
201021
SERVICE POINTS OF DISASSEMBLYMZZMFAW
14. REMOVAL OF SPRING PINRemove the spring pin using a pin punch.
NOTE\,/If the spring pin interferes with the synchronizer ring or
cone gear, rotate the gear for dislocation and remove the
spring pin.15.16. REMOVAL OF LOCK NUTS
(1) Unstake lock nuts of the input shaft and intermediate
gear.
(2) Shift the transaxle in reverse using the control lever and
select lever.(3) Install the special tool onto the
inout shaft.
(4) Screw a bolt [IO mm] into the hole on the periphery ofclutch housing and attach a spinner handle to the
special tool.
(5) Remove the lock nut, while using the bolt as a spinner
handle stopper.48.49. REMOVAL OF SPRING PINS
Remove the spring pins for 1 st-2nd and 3rd-4th speed shiftforks using a pin punch.
TSB RevisionI
1

22-24
MANUAL TRANSAXLE - Transaxle Assembly
63. INSTALLATION OF OIL SEALInstall the input shaft front oil seal using the special tool.
MD998321-01
Oil seal2010041
50. INSTALLATION OF SHIFT RAIL ASSEMBLY
(1) Set the 1 st-2nd speed shift sleeve at 2nd speed.
(2) Set the 3rd-4th speed shift sleeve at 4th speed.
(3) Fit the shift forks of shift rail assembly to groove of
sleeves.
‘LJ(4) Insert the shift rails into the shift rail holes of clutch
housing.
(5) Turn the shift rails in the directions indicated by the
arrows in the order shown in the illustration, and
engage the shift lugs to control finger and the interlock
plate.48.49. INSTALLATION OF SPRING PINS
(1) Install the spring pins using the special tool or a pin
punch.
CautionDo not reuse the spring pins.
TSB Revision

22-26MANUAL TRANSAXLE . - Transaxle Assembly
Amountl-2 mm
27. INSTALLATION OF OIL GUIDEInstall the oil guide to the transaxle case as illustrated.
26. INSTALLATION OF TRANSAXLE CASE(1) Place the selected spacers on the intermediate gear
and differential’s bearing outer race. Also insert the
selected spacer between the output shaft bearing outer
race and the transaxle case.
(2) Set so that the threaded hole of the reverse idler gearshaft’s head is facing in the direction indicated in the
illustration.
NOTE
If there is a great deviation in the direction in which the
threaded hole is facing, it will be impossible to align thethreaded hole and the hole in the case after the
transaxle case is installed.
(3) Apply specified sealant to the clutch housing side of the
transaxle case.
Specified’ sealant: MITSUBISHI genuinePart No. MD997740 or equiva-
lentLJ
Caution
Squeeze out sealant from the tube uniformly with-
out excess or discontinuity.(4) Install the transaxle case onto the clutch housing.
(5) Insert a Phillips screwdriver
[8 mm (.32 in.) shaft
diameter] into the bolt hole in the case, as shown in thefigure, and use it to align the threaded hole of the
reverse idler gear shaft with the bolt hole in the
transaxle case.
(6) Install the reverse idler gear shaft bolt and tighten thebolt by fingers.
(7) Tighten the all transaxle tightening bolts to specified
torque.(8) Tighten the reverse idler gear shaft bolt to specified
torque.16.15. INSTALLATION OF LOCK NUTS
(1) Install the special tool to the splined end of input shaft.(2) Screw a bolt
[lo mm (.40 in.)] into the hole on the
periphery of clutch housing and attach a spinner handleto the special tool.
TSB Revision

MANUAL TRANSAXLE - Transaxle Assembly22-27
(3) Shift the transaxle in reverse using control lever and
select lever.
(4) Tighten the lock nut to specified torque, while using thebolt attached in the above step as a spinner handle
stopper.(5) Loosen the lock nuts.
(6) Retighten the lock nuts to the specified torque.
(7) Stake the lock nut.
IMD998245-01Spring pir
Shift rail
14. INSTALLATION OF SPRING PIN(1)
rr;‘tl.the spring pin using the special tool or a pin
CautionDo not reuse the spring pins.
(2) When installing, make sure that the slit of the spring pinis aligned with the shift rail center line.
TSB RevisionI