run flat MITSUBISHI 3000GT 1991 Service Manual

31-1
ii~
WHEEL.I
AND TIRE~
CONTENTSM3IA& -
SERVICE ADJUSTMENT PROCEDURES............4TROUBLESHOOTING:...........................................3
Tire Inflation Pressure Check................................4Bald Spots
Tire Wear Check....................................................4
Cracked Treads
Wheel Runout Check............................................4Feathered Edge
SPECIFICATIONS2Rapid Wear at Center....................................................
General Specifications2Rapid Wear at Shoulders........................................
Service Specifications........................................2Scalloped Wear
Torque Specifications2Wear on One Side............................................

31-2WHEEL AND TIRE - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONS
MOICA- -
‘\
Items
Wheel
Tire size
Wheel type
Wheel size
Amount of wheel offsetmm (in.)
Tire inflation pressure
kPa (psi)
Front
Rear
DOHC-N/A
225l55R 16 93U
Aluminum type
16X8J ’
46 (1.8)
220 (32)
200 (29)DOHC-T/C
245145ZR 17
Aluminum type
17 x
8.5J
46 (1.8)
220 (32)
200 (29)
Spare wheel
Tire size
T125190D16T135/90D16
Wheel size
l6x4Tl6x4T
Amount of wheel offsetmm (in.)46 (1.8)46 (1.8)
Tire inflation pressurekPa (psi)
420 (60)420 (60)
SERVICE SPECIFICATIONSM31CB. -
Items
Specifications
Limit
Wheel
runout
Radialmm (in.)2.0 (.08)
Lateralmm (in.)2.0 t.08)
Tread depth of tiremm (in.)1.6 (.06)
TORQUE SPECIFICATIONSMBlCC- -
ItemsNm
Hub nuts120- 140
ft.lbs.
87-iO1TSB Revision

WHEEL AND TIRE - Service Adiustment ProceduresllFOO1753Y510
Wear indicator
/LateralllFOO1:
1SERVICE ADJUSTMENT PROCEDURES
TIRE INFLATION PRESSURE CHECKM3lFDA.E
Check the inflation pressure of the tires. If it is not within the
standard value, make the necessary adjustment.
TIRE WEAR CHECKMJlFBAC
Measure the tread depth of tires.
Limit: 1.6 mm
(.06 in.)
If the remaining tread depth is less than the limit, replace the
tire.
NOTE
When the tread depth of tire is reduced to 1.6 mm (.06 in.) orless, wear indicator will appear.
WHEEL RUNOUT CHECKM31 FCAEJack up the vehicle so that the wheels are clear of the floor.
While slowly turning the wheel, measure wheel runout with a
dial indicator.
Limit:
Radial2.0 mm
(.08 in.)
Lateral2.0 mm (.08 in.)
If wheel
runout exceeds the limit, replace the wheel.
TSB Revision

STEERING - Service Adjustment Procedures37A-9
LL:13N002E
FluId f[uctuatlon
While
engineWhile engme
runningstopped13uo13:
Return ho
Vinyl hose13AO142
j
1.Press in V-belt at the illustrated position with about 100 N
(22 Ibs.) and measure deflection.
Standard value:
When belt tension is inspectedor readjusted
When new belt is installed
/ 9 - 11 mm (.35 - .43 in.)
I
’ 7 - 8.5 mm (.28 - .33 in.)
2.If the deflection is out of the standard values, adjust the belt
tension using the following procedure.
(1) Loosen the tension pulley’s securing bolts A and
B.(2) Mount the extension bar on the tension pulley.
(3) While increasing the tension of the V-belt with the
extension bar, retighten the tension pulley’s securing
bolts A and B in the order mentioned.
FLUID LEVEL CHECKM37FlAJ
1.Park the vehicle on a flat, level surface, start the engine, and
then turn the steering wheel several times to raise the
temperature of the fluid to approximately 50
- 60°C (122 -
140°F).
2.With the engine running, turn the wheel all the way to the
left and right several times.
3.Check the fluid in the oil reservoir for foaming or milkiness.
Check the difference of the fluid level when the engine is
stopped, and while it is running. If the fluid level changes
considerably, air bleeding should be done.
FLUID REPLACEMENTM37FJAL1. Raise the front wheels on a jack, and then support them
with rigid racks.
2. Disconnect the return hose connection.
3. Connect a vinyl hose to the return hose, and drain the oil
into a container.
4. Disconnect the high-tension cable, and then while operat-
ing the starting motor intermittently, turn the steering
wheel all the way to the left and right several times to drain
all of the fluid.
Caution
Be careful not to position the high-tension cable nearthe carburetor or the delivery pipe.
5.Connect the return hoses securely, and then secure it with
the clip.
6.Fill the oil reservoir with the specified fluid up to the lower
position of the filter, and then bleed the air.
Specified fluid:MITSUBISHI PLUS ATF/Automatic
transmission fluid “DEXRON” or
“DEXRON II”
1 TSB Revision