speed sensor MITSUBISHI MONTERO 2000 Service Repair Manual

AUTOMATIC TRANSMISSION -Troubleshooting 23-59
Inspection procedure 18
Dual pressure switch system
Probable cause
The cause is probably a malfunction of thedualpressure switch circuit, or of the
engine-A/T-ECU or A/T-ECU.DMalfunction of dualpressure switch
DMalfunction of harness or connector
DMalfunction of A/C system
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
Dual pressure switch check
(Refer to GROUP 55 – On-Vehicle Service.)NG
Measure at engine-A/T-ECU connector D-121
<6G7> or at A/T-ECU connector D-107 <4M4>.
DDisconnect the connector and measure at the
harness side.
DIgnition switch: ON
DA/C switch: ON
D<6G7> Voltage between terminal 83 and earth
<4M4> Voltage between terminal 10 and
earth
OK:System voltage
OKCheck the following connectors:<6G7> D-121,
A-04,<4M4> D-107,A-04NG
Repair OK
Check the trouble symptoms.Replace
A/C system check (Refer to GROUP 55 -
Troubleshooting.)NG
Replace the engine-A/T-ECU or A/T-ECU. NG
Inspection procedure 19
Vehicle speed sensor system
Probable cause
The cause is probably a malfunction of the vehicle speed sensor circuit, or of
the A/T-ECU or the engine-A/T-ECU.DMalfunction of vehicle speed sensor
DMalfunction of connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
MUT-
IIData List
DNo.29 Vehicle speed sensor
OK:Refer to P.23-61 (Data List Chart).NO
Speedometer check
(Refer to GROUP 54A - Combination Meter.)
OK
OKNG NG
YES
Is the speedometer correct?
OK
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
Check the trouble symptoms.
Replace the engine-A/T-ECU or A/T-ECU.NG
Check the following connectors:<6G7> C-09, E-113, E-13,
D-121<4M4>C-09, E-113, E-13, D-109
DCheck the harness between the engine-A/T-ECU and the
vehicle speed sensor. <6G7>
DCheck the harness between the A/T-ECU and the vehicle
speed sensor.<4M4>Repair
NG
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-61
DATA LIST REFERENCE TABLE
Data
list No.Check itemInspection conditionsNormal condition
11APSIgnition switch: ON
Engine: StoppedAccelerator pedal:
Fully closed985 - 1085 mV
Engine: Stopped
Selector lever posi-
tion: P
Accelerator pedal:
DepressedGradually increases from the above
value.
Accelerator pedal:
Fully open4000 mV or higher
15A/T fluid tempera-
ture sensorDriving after en-
gine has warmed
upDrive for 15 minutes
or more until the ATF
temperature reaches
70 - 80°C.Gradually increases to 70 - 80°C.
21Crank angle sen-
sor <6G7>Engine: Idling
Selector lever posi-Compare the engine
speeds displayed onIdentical
sor <6G7>
Engine speed sen-
sor <4M4>Selector lever posi-
tion: Pspeeds displayed on
the tachometer and
the MUT-II.
22Input shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
23Output shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
25Wide open throttleAccelerator pedalReleasedOFF
switchpositionDepressedON
26Stop lamp switchIgnition switch: ON
Engine: StoppedBrake pedal: De-
pressedON
Engine: Stopped
Brake pedal: Re-
leasedOFF
29Vehicle speed sen-
sorSelector lever posi-
tion: Sports modeIdling in 1st
(Vehicle stopped)0 km/h
Driving at a constant
speed of 50 km/h in
3rd50 km/h
31LR solenoid valve
duty ratioSelector lever posi-
tion: Sports modeData List No.No. 31No. 32No. 33No. 34No.35
32UD solenoid valve
duty ratioDriving at a constant
speed in 1st0%0%100%100%0%
332nd solenoid valve
duty ratioDriving at a constant
speed in 2nd100%0%0%100%0%
34OD solenoid valve
duty ratioDriving at a constant
speed in 3rd100%0%100%0%0%
35RED solenoid
valve duty ratioDriving at a constant
speed in 4th0%0%100%0%100%
Driving at a constant
speed in 5th100%100%0%0%100%


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-67
Ter-
minal
No.Standard value Inspection conditions Check item
10A/C compressor load signalA/C switch: OFF0V
A/C switch: ONSystem voltage
11Power supplyIgnition switch: OFF0V
Ignition switch: ONSystem voltage
12EarthAt all times0V
13EarthAt all times0V
14OD solenoid valveEngine: Idling
Shift range: 3rdSystem voltage
Engine: Idling
Shift range: Park7-9V
15DCC solenoid valveEngine: Idling
Shift range: 1stSystem voltage
162nd solenoid valveEngine: Idling
Shift range: 2ndSystem voltage
Engine: Idling
Shift range: Park7-9V
172nd shift indicator lampShift range: 2ndSystem voltage
Shift range: Other than the above0V
184th shift indicator lampShift range: 4thSystem voltage
Shift range: Other than the above0V
24Power supplyIgnition switch: OFF0V
Ignition switch: ONSystem voltage
25EarthAt all times0V
26EarthAt all times0V
31Input shaft speed sensorMeasure between terminals (31) and (43) using an
oscilloscope.
Engine: 2 000 r/min
Shift range: 4thCheck Procedure
using an Oscillo-
scope (Refer to
P.23-69.)
32Output shaft speed sensorMeasure between terminals (32) and (43) using an
oscilloscope.
Engine: 2 000 r/min
Shift range: 4thCheck Procedure
using an Oscillo-
scope (Refer to
P.23-69.)
33Engine speed sensorEngine: Idling2.0 - 2.4 V
38Backup power supplyAt all timesSystem voltage
43Sensor earthAt all times0V
44A/T fluid temperature sensorA/T fluid temperature 20°C3.8 - 4.0 V
A/T fluid temperature 40°C3.2 - 3.4 V
A/T fluid temperature 80°C1.7 - 1.9 V
45Accelerator pedal positionAccelerator pedal: Fully closed (engine stopped)0.985 - 1.085 V
sensor (APS)Accelerator pedal: Fully open (engine stopped)4.0 V or higher
51RED solenoid valveEngine: Idling
Shift range: 5thSystem voltage
Engine: Idling
Shift range: Park7-9V
53Output communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-68
Ter-
minal
No.Standard value Inspection conditions Check item
54Input communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D
55Inhibitor switch PIgnition switch: ON
Selector lever position: PSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
56Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
57Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
58Downshift switchIgnition switch: ON
Selector lever position: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
59Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V
62DIR solenoid valveEngine: Idling
Shift range: ParkSystem voltage
Engine: Idling
Shift range: 2nd7-9V
65Wide open throttle switchAccelerator pedal: Released4.5 - 5.5 V
Accelerator pedal: DepressedLess than 0.4 V
66Inhibitor switch RIgnition switch: ON
Selector lever position: RSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
67Inhibitor switch DIgnition switch: ON
Selector lever position: DSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
68Upshift switchIgnition switch: ON
Selector lever position: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
69Vehicle speed sensorWhen stopped0V
When starting to drive forward slowly.0 V and 5 V alter-
nates
71A/T control relayIgnition switch: OFF0V
Ignition switch: ON10 - 12 V
72EarthIgnition switch: ON0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-75
Code No. 22, 23 Front propeller shaft speed sensor
systemProbable cause
Code No. 22 is output to indicate anopencircuit or short-circuit in the front
propeller shaft speed sensor if no signal is input from the front propeller shaft
speed sensor when shifting from 2WD to 4WD while driving atmedium to low
speeds.
Code No. 23 is output to indicate anopencircuit or short-circuit in the front
propeller shaft speed sensor if the signal input from the front propeller shaft
speed sensor is unstable when the freewheelengageswitch is on.DMalfunction of front propeller shaft speed sensor
DMalfunction of harness or connector
DMalfunction of transfer-ECU
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
OK NG
OK
OK
To the nextpage
NG
OK
NG
NG
Repair
Replace the transfer-ECU.
OKMUT-
IIData List
DNo. 2 Front propeller shaft speed sensor
OK:Refer to P.23-87 (Data List Chart).
OK
OK
NG
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminals 18 and earth
OK:0.5 V or less
NG
Repair
Replace the transfer-ECU.
NG
Check the trouble symptoms.
Check the trouble symptoms.
Replace the transfer-ECU.
OK
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDisconnect front propeller shaft speed sensor connector
C-17.
DIgnition switch: ON
DVoltage between terminals 7 and earth
OK:4.8 - 5.2 V
Measure the front propeller shaft speed sensor output wave
pattern at transfer-ECU connector E-105 (using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 3rd
DVoltage between terminals 7 - 18
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope tern B>) should be output, and the maximum value
should be 4.8 V or more and the minimumvalue
should be 0.8 V or less.
There should be no noise in the output wave pattern.
NG
RepairCheck the following connectors:C-17, E-105NG
NG
Repair
Check the following connector:E-105Repair
NG
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU.
Check the following connector:C-17
Check the trouble symptoms.
Check the following connector:E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-76
(2)NG
(3)NG
From the previouspage
(1)NG
OK
NG
Measure at front propeller shaft speed sensor connector C-17.
DDisconnect the connector and measure at the harness
side.
(1) Resistance between terminal 1 and earth
OK:2
Wor less
(2) Voltage between terminal 2 and earth
(Ignition switch: ON)
OK:4.8 - 5.2 V
(3) Voltage between terminal 3 and earth
(Ignition switch: ON)
OK:System voltage
Check the harness between the front propeller shaft speed
sensor and the ignition switch, and repair if necessary.
Check the following connectors:D-208, D-213, D-32, E-115
NG
Check the trouble symptoms.
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Earth
line)
Replace the front propeller shaft speed sensorOK
OK
Repair
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Sensor
line)
Eliminate the cause of the noise.
NG
Check the trouble symptoms.
NG
Repair
OK
NG
Repair
OK
DCheck the harness between the front propeller shaft speed
sensor and the transfer-ECU.
DCheck the harness between the front propeller shaft speed
sensor and the ignition switch.
Check the following connectors:D-208, D-213, D-32, E-115,
E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-77
Code No. 24, 25 Rear propeller shaft speed sensor systemProbable cause
Code No. 24 is output to indicate anopencircuit or short-circuit in the rear
propeller shaft speed sensor if the signal input from the rear propeller shaft
speed sensor is unstable when the APS voltage is 1.5 V or higher.
Code No. 25 is output to indicate anopencircuit or short-circuit in the rear
propeller shaft speed sensor if the signal input from the rear propeller shaft
speed sensor is unstable when the freewheelengageswitch is on.DNo. 3 Rear propeller shaft speed sensor
DMalfunction of harness or connector
DMalfunction of transfer-ECU
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
OK NG
Check the following connector:E-105
OK
OK
To the nextpage
NG
OK
NG
NG
Repair
Check the following connector:C-08
Replace the transfer-ECU.
OKMUT-
IIData List
DNo. 3 Rear propeller shaft speed sensor
OK:Refer to P.23-87 (Data List Chart).
OK
OK
NG
Check the trouble symptoms.
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminals 18 and earth
OK:0.5 V or less
NG
Repair
Replace the transfer-ECU.
NG
Check the trouble symptoms.
Check the trouble symptoms.
Replace the transfer-ECU.
OK
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDisconnect rear propeller shaft speed sensor connector
C-08.
DIgnition switch: ON
DVoltage between terminals 9 and earth
OK:4.8 - 5.2 V
Measure the rear propeller shaft speed sensor output wave
pattern at transfer-ECU connector E-105 (using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 3rd
DVoltage between terminals 9 - 18
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope) should be
output, and the maximum value should be 4.8 V or
more and the minimumvalue should be 0.8 V or
less.
There should be no noise in the output wave pattern.
NG
RepairCheck the following connectors:C-08, E-108NG
NG
Repair
Check the following connector:E-108Repair
NG
Check the harness between the rear propeller shaft speed
sensor and the transfer-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-78
(2)NG
(3)NG
From the previouspage
(1)NG
OK
NG
Measure at rear propeller shaft speed sensor connector C-08.
DDisconnect the connector and measure at the harness
side.
(1) Resistance between terminal 1 and earth
OK:2
Wor less
(2) Voltage between terminal 2 and earth
(Ignition switch: ON)
OK:4.8 - 5.2 V
(3) Voltage between terminal 3 and earth
(Ignition switch: ON)
OK:System voltage
Check the harness between the rear propeller shaft speed
sensor and the ignition switch, and repair if necessary.
Check the following connectors:D-208, D-213, D-32, E-115
NG
Check the trouble symptoms.
Check the harness between the rear propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Earth
line)
Replace the rear propeller shaft speed sensorOK
OK
Repair
Check the harness between the rear propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Sensor
line)
Eliminate the cause of the noise.
NG
Check the trouble symptoms.
NG
Repair
OK
NG
Repair
OK
DCheck the harness between the rear propeller shaft speed
sensor and the transfer-ECU.
DCheck the harness between the rear propeller shaft speed
sensor and the ignition switch.
Check the following connectors:D-208, D-213, D-32, E-115,
E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting II>23-87
DATA LIST REFERENCE TABLE
Item
No.Check itemInspection conditionsNormal condition
1Accelerator pedalEngine: StoppedAccelerator pedal: Fully closed985 - 1,085 mV
position sensor
(APS)Selector lever position:
PAccelerator pedal: DepressedGradually increases from
the above value.
Accelerator pedal: Fully open4000 mV or higher
2Front propeller shaft
speed sensorTransfer position: 4WDDriving at a constant speed of
30 km/h30 km/h
3Rear propeller shaftTransfer position: 4WDDriving at a constant speed of30 km/h3Rear propeller shaft
speed sensorTransfer position: 4WDDriving at a constant speed of
30 km/h30 km/h
4Difference between
front and rear pro-
peller shaft speedsTransfer position: 4WDDriving at a constant speed of
30 km/hWithin 5 km/h
5Vehicle speedIdling in 1st (Vehicle stopped)0 km/h
Driving at a constant speed of 50 km/h in 3rd50 km/h
6Transfer lever posi-Ignition switch: ONTransfer shift lever position: 2H2H
tionEngine: StoppedTransfer shift lever position: 4H4H
Transfer shift lever position:
4HLc4HLc
Transfer shift lever position:
4LLc4LLc
7Transfer positionDriving at a constant
speed of 10 km/hTransfer shift lever position:
2H®4H2H - 4H®4H
Transfer shift lever position:
4H®4HLc4H - 4HL®4HL
Engine: Stopped
Selector lever position:Transfer shift lever position:
4HLc®4LLc4HL - 4LL®4LL
NTransfer shift lever position:
4LLc®4HLc4HL - 4LL®4HL
Driving at a constant
speed of 10 km/hTransfer shift lever position:
4HLc®4H4H - 4HL®4H
Transfer shift lever position:
4H®2H2H - 4H®2H
8Main relay voltageIgnition switch: ONSystem voltage (V)
9Ignition voltageIgnition switch: ONSystem voltage (V)
10Shift actuator cur-
rentDuring transfer selection (while motor is running)0A®0.2 A®0A
11Target currentDuring transfer selection (while motor is running)0A®1.5 A®0A
12Shift actuator volt-
ageIgnition switch: ON
Selector lever position: N
Transfer shift lever position: 2H®4H (or 4H®4HLc,
4HLc®4LLc)System voltage (V)
Ignition switch: ON
Selector lever position: N
Transfer shift lever position: 4LLc®4HLc (or 4HLc®4H,
4H®2H)System voltage (V)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting II>23-90
Ter-
minal
No.Check itemInspection conditionsStandard value
1Shift actuatorTransfer shift lever position: 2H®4H5.6 V®11.0 V®
5.6 V
3Shift actuatorTransfer shift lever position: 4H®2H5.6 V®11.0 V®
5.6 V
5Accelerator pedal positionAccelerator pedal: Fully closed (engine stopped)0.985 - 1.085 V
sensor (APS)Accelerator pedal: Fully open (engine stopped)4.0 V or higher
7Front propeller shaft speed
sensorMeasure the voltage between terminals 7 and 18 using
an oscilloscope.
Engine: 2 000 r/min
Shift range: 4thOscilloscope check
procedure (Refer to
P. 23-69 Pattern B>.)
9Rear propeller shaft speed
sensorMeasure the voltage between terminals 9 and 18 using
an oscilloscope.
Engine: 2 000 r/min
Shift range: 4thOscilloscope check
procedure (Refer to
P. 23-69 Pattern B>.)
11Diagnosis outputWhen normal (no diagnosis codes are output)0 V and 5 V alterna-
tes
13Power supplyIgnition switch: OFF0V
Ignition switch: ONSystem voltage
18Sensor earthAt all times0.5 V or less
20Transfer lever switch 2HTransfer shift lever position: 2HSystem voltage
Transfer shift lever position: Other than the above0V
21Transfer lever switch 4HTransfer shift lever position: 4HSystem voltage
Transfer shift lever position: Other than the above0V
22Transfer lever switch 4HLcTransfer shift lever position: 4HLcSystem voltage
Transfer shift lever position: Other than the above0V
23Transfer lever switch 4LLcTransfer shift lever position: 4LLcSystem voltage
Transfer shift lever position: Other than the above0V
24Diagnosis control––
25EarthAt all times0V
26EarthAt all times0V
31Backup power supplyAt all timesSystem voltage
32Inhibitor switch NSelector lever position: NSystem voltage
Selector lever position: Other than the above0V
33Inhibitor switch PSelector lever position: PSystem voltage
Selector lever position: Other than the above0V
34Stop lamp switchBrake pedal: DepressedSystem voltage
Brake pedal: Released0V
35EarthAt all times0V
37Rear wheel indicator lampOther than during transfer selectionSystem voltage
38Front wheel indicator lampDuring 4WDSystem voltage
39Earth <6G7>At all times0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk