service MITSUBISHI MONTERO 2000 Service User Guide

ENGINE <6G7> -General Information/Service Specifications11A-3
GENERAL INFORMATION
Items6G74-GDI
Total displacement ml3,497
Bore´Stroke mm93´85.8
Compression ratio10.4
Combustion chamberPentroof + ball-in-piston
Camshaft arrangementDOHC
Number of valveIntake12
Exhaust12
Valve timingIntakeOpeningBTDC 8_
ClosingABDC 56_
ExhaustOpeningBBDC 48_
ClosingATDC 16_
Fuel systemElectronically controlled multipoint fuel injection
Rocker armRoller type
Auto-lash adjusterEquipped
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
Basic ignition timing5_BTDC±3_-
Ignition timingApprox. 20_BTDC*1-
Idle speed r/min600±100*1-
CO contents %0.5 or less-
HC contents ppm100 or less-
Compression pressure (at engine speed of 280 r/min) kPa1,275980
Compression pressure difference of all cylinders kPa-Max. 98
Intake manifold vacuum kPa-Min. 56*2
Auto tensioner rod depth (mm)Within 1-
Timing belt tension torque N×m4.4-
Auto-tensioner rod protrusion amount mm3.8 - 5.0-
NOTE
*1: Indicates the value measured within 4 minutes since the engine was started.
*2: Indicates the value when more than 4 minutes have passed since the engine was started.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

11B-1
ENGINE <4D5>
CONTENTS
GENERAL INFORMATION 2..................
SERVICE SPECIFICATIONS 3.................
SEALANTS 3................................
SPECIAL TOOLS 4..........................
ON-VEHICLE SERVICE 5.....................
Drive Belt Tension Check and Adjustment 5......
Auto-tensioner check 7.........................
Valve Clearance Check and Adjustment 8........
Injection Timing Check and Adjustment 9........
Idle Speed Check and Adjustment 12............
Idle-up Mechanism Check and
Adjustment-For A/C 12.........................Compression Pressure Check 13................
Timing Belt Tension Adjustment 14..............
Timing Belt B Tension Adjustment 15............
OIL PAN AND OIL SCREEN 17..............
TIMING BELT AND TIMING BELT B 19......
CRANKSHAFT OIL SEAL 25.................
CAMSHAFT AND CAMSHAFT OIL SEAL 27..
CYLINDER HEAD GASKET 30...............
ENGINE ASSEMBLY 34.....................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE <4D5> -Service Specifications/Sealants11B-3
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
A/C compressor drive beltVibration frequency Hz157 - 176–
(When inspection)Tension N260 - 325–
Deflection mm 8.0 - 8.5–
A/C compressor drive beltVibration frequency Hz157 - 176–
(When adjustment)Tension N260 - 325–
Deflection mm 8.0 - 8.5–
A/C compressor drive beltVibration frequency Hz192 - 208–
(When replacement)Tension N390 - 450–
Deflection mm 6.5 - 7.0–
Valve clearance (at hot) mm0.25-
Injection timing (Value indicated on dial gauge mm)9_ATDC (1±0.03)-
Idle speed r/min750±100-
Compression pressure kPa (at engine speed of 280 r/min)3,040Min. 2,256
Compression pressure difference of all cylinder (at engine speed of 280
r/min) kPa-Max. 294
Timing belt tension mm4-5
Timing belt B tension mm4-5
SEALANTS
ItemsSpecified sealantRemarks
Oil panMITSUBISHI GENUINE PART
MD970389 or equivalentSemi-drying sealant
Semi-circular packing and rocker
cover gasket seal, and cylinder head
seal3M ATD Part No. 8660 or equivalent


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

11B-1
ENGINE <4D5>
CONTENTS
GENERAL 2.................................
Outline of Changes 2...........................
GENERAL INFORMATION 2..................
SERVICE SPECIFICATIONS 2.................
SEALANT 2..................................
SPECIAL TOOLS 3...........................ON-VEHICLE SERVICE 4.....................
Injection Timing Check and Adjustment 4.........
Idle Speed Check 4............................
OIL PAN AND OIL SCREEN 5................
TIMING BELT AND TIMING BELT B 7........
CYLINDER HEAD GASKET 13................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE <4D5> -General/General Information/Service Specifications/Sealant11B-2
GENERAL
OUTLINE OF CHANGES
Some service procedures have been revised as the following changes have been made to comply to
the Emission Regulation StepIII.
DInjection timing and idle speed check and adjustment have bee changed as the electronic-controlled
fuel injection pump has been introduced.
DThe oil pan has a cover in order to reduce noise due to an enhanced engine output.
DA crank angle sensor and crankshaft sensing blade have been added due to the introduction of
an electronic-controlled fuel injection pump. Due to this change, the timing belt front lower cover
has been reshaped.
DThe tightening torque of the cylinder head bolts and the cylinder head gasket have been changed.
GENERAL INFORMATION
Items4D56
Total displacement mL2,477
Bore x Stroke mm91.1 x 95.0
Compression ratio21
Combustion chamberVortex chamber type
Camshaft arrangementSOHC
Number of valveIntake4
Exhaust4
Valve timingIntakeOpeningBTDC 20_
ExhaustClosingABDC 49_
IntakeOpeningBBDC 55_
ExhaustClosingATDC 22_
Fuel systemElectronically controlled type injection pump
Rocker armRoller type
Adjusting screwElephant foot type
SERVICE SPECIFICATIONS
ItemsStandard value
Idle speed r/min750±30
Timing belt tension mm4-5
Timing belt B tension mm4-5
SEALANT
ItemsSpecified sealantRemarks
Oil panMITSUBISHI GENUINE PART
MD970389 or equivalentSemi-drying sealant


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

11C-1
ENGINE <4M4>
CONTENTS
GENERAL INFORMATION 2..................
SERVICE SPECIFICATIONS 2.................
SEALANTS AND ADHESIVES 3..............
SPECIAL TOOLS 3..........................
ON-VEHICLE SERVICE 5.....................
Drive Belt Tension Check and Adjustment 5......
Valve Clearance Check and Adjustment 8........
Injection Timing Check and Adjustment 9........
Idle Speed Check 12...........................Compression Pressure Check 12................
OIL PAN 14.................................
VACUUM PUMP 16..........................
TIMING CHAIN 17...........................
CRANKSHAFT OIL SEAL 21.................
CAMSHAFT 23..............................
CYLINDER HEAD GASKET 27...............
ENGINE ASSEMBLY 33.....................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE <4M4> -General Information/Service Specifications11C-2
GENERAL INFORMATION
Items4M41
Total displacement mL3,200
Bore´Stroke mm98.5´105.0
Compression ratio17.0
Camshaft arrangementDOHC
Number of valveIntake8
Exhaust8
Valve timingIntakeOpeningBTDC 13_
ClosingABDC 31_
ExhaustOpeningBBDC 55_
ClosingATDC 17_
Fuel systemDistribution type injection pump
Rocker armRoller type
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
Alternator drive beltVibration frequency Hz122 - 161–
(When inspection)Tension N207 - 363–
Deflection mm 8-11–
Alternator drive beltVibration frequency Hz122 - 136–
(When adjustment)Tension N207 - 259–
Deflection mm 10 - 11–
Alternator drive beltVibration frequency Hz149 - 161–
(When replacement)Tension N311 - 363–
Deflection mm 8-9–
A/C compressor drive beltVibration frequency HzA177 - 191–
(When inspection)B145 - 156–
Tension NC343 - 392–
Deflection mm
C7.5 - 8.5–
A/C compressor drive beltVibration frequency HzA177 - 191–
(When adjustment)B145 - 156–
Tension NC343 - 392–
Deflection mm
C7.5 - 8.5–
A/C compressor drive beltVibration frequency HzA177 - 191–
(When replacement)B145 - 156–
Tension NC490 - 539–
Deflection mm
C6.0 - 6.5–


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE <4M4> -On-vehicle Service11C-13
8. If there is a cylinder which compression or compression
difference is outside the limit, pour a small amount of
engine oil through the glow plug hole, and repeat the
operations in steps 6 - 7.
(1) If the compression increases after the oil is added,
the cause of the malfunction is a worn or damaged
piston ring and /or cylinder inner surface.
(2) If the compression does not rise after the oil is added,
the cause is a burnt or defective valve seat, or pressure
is leaking from the gasket.
9. Connect the fuel cut solenoid valve connector.
10. Install the glow plugs.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE <4M4> -Cylinder Head Gasket11C-27
CYLINDER HEAD GASKET
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
DEngine Coolant Drain and Refill
(Refer to GROUP 14 - On-vehicle Service.)
DEngine Oil Check andRefill
(Refer to GROUP 12 - On-vehicle Service.)

DFuel Line Air-bleeding
(Refer to GROUP 13C - On-vehicle Service.)

DDrive Belt TensionCheck and Adjustment
(Refer to P.11C-5.)DCamshaft Removal and Installation
(Refer to P.11C-20.)
DCooling Fan and Fan Clutch Assembly Removal and
Installation (Refer to GROUP 14.)
DIntake Manifold Removal and Installation
(Refer to GROUP15.)
DTurbocharger Removal and Installation
(Refer to GROUP15.)
DExhaust Manifold Removal and Installation
(Refer to GROUP15.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

Service Bulletins
Click on the applicable bookmark to select the Service Bulletin.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk