engine oil NISSAN 300ZX 1984 Z31 Automatic Transmission Workshop Manual

GENERAL SERVICE NOTICE
I (Cont'd) Oil Cham
OIL CHANNELS IN DRUM SUPPORT OIL CHANNELS IN CONVERTER HOUSING
To lock-up ~ontrol valve
rDrain (E4N71Bl
clutch (Front)
Forward clutch
clutch pressure Front & 0 0 lubrmtmn
SAT706
3peration Mechanic:
In the E4N71B and 4N71B automatic transmission, each part operates as shown in the following table at
each gear select position
'arking
pawl
Htgh-
'everse
Front) Forward clutch (Rear) 0 D band servo Direct
clutch Range -
Release
ON ON
1 Reverse 1 ON 1 ION) ON
+-
ON I
I Neutral I ON I (ON) ON
T-
ON
-
ON
-
ON
ON
JT
I ION
'34
(0 D 1 ON I ON
Second I ON I (ON) ON
1 ON I (ON) 12
(Second) ON ON I ON
ON ord ON I I ON
The low & reverse brake IS applied In "1 I" range to prevent free wheeling when coasting and allows engine braking.
AT-7

TROUBLE-SHOOTING AND DIAGNOSES
Pressure Testing ~ ~~
2
LINE PRESSURE
1 Install
pressure gauge to line pressure port
785 - 1,128 (8 0- 11 5, 114- 164)
SAT765
1
2 Warm up engine until engine oil and AT F
reach operating temperatures.
A.T.F. temperature:
3 Set parking brake and block wheels.
4 Measure line pressure at idle and at stall point
while depressing brake pedal
fully
50 ~ 80°C (122 - 176°F)
275 - 373 (2 8.3 8.40.54)
At idling
VG90E engine without turbo
Range 1 Line pressure kPa (kg/crn2. psi)
R I 451 -588(46-60,65-85)
D 1 275-373(28-38.40-54)
2 I 785.1,079 (80- 11 0,114- 156)
1 1 275-373(28-38.40-54)
VG3OE turbo engine
Range Line pressure kPa (kg/cm2, psi)
304-441 (31-45.44-64)
275
- 373 (2 8.38.40.54)
At stall test
1 Start engine and place select lever in "D"
range
2 Apply foot brake and accelerate to wide-open
throttle
3 Quickly note the line pressure and immediately
release throttle
4 Shift select lever to "N".
5 Cool off A.T F.
6 Perform line pressure testing in the same man-
ner as in steps 2 through 6 with select lever
in
"2". "1" and "R", respectively.
Do not perform tests for more than five
seconds
at any shift range.
Do not proceed to next "range" test imrnedi-
ately after one "range"
test is done. Wait until
oil temperature decreases
AT-91

TROUBLE-SHOOTING AND DIAGNOSES
Pressure Testing (Cont'd)
Intake manifold
vacuum
kPa (mmHg,
inHsl
VG30E engine without turbo
Propeller $haft
Vehicle speed revolutions
kmlh (MPH)
rpm
Range I Line pressure kPa (kglcm', psi)
Intake manifold
vacuum
kPa (mrnHg.
inHg) ~
R I 1,961 - 2,393
(20 0.24 4,284 .347)
Propeller shaft Vehicle speed
kmlh (MPH) revolutions
rpm
D I 1.079-1,226(110-125,156-178)
2 I 1,079 - 1,275 (11 0.13 0, 156 - 185)
1 I 1,079 - 1,226 (1 1 0 - 12 5, 156 - 178)
VG30E turbo engine
Range I Line pressure kPa (kgtcm', psi)
R I 1,961 - 2,354 (20 0 - 24 0,284 - 341)
D I 1,667 - 1,883 (17 0- 19 2,242 -273)
2 I 1.667-1,883(170-192,242-273)
1 I 1.667-1.8831170-192.242-273)
Judgment by measuring line pressure
If line pressure does not rise, first check to make
sure that vacuum
hose is connected properly.
1) When line pressure is low at all positions, the
problem may be due to
Wear on interior of oil pump
Oil leakage at or around oil pump, control
valve body, transmission case or governor
Sticking pressure regulator valve
Sticking pressure modifier valve
2) When line pressure is low at a particular posi-
tion, the problem may be due to the following
If oil leaks at or around forward clutch (rear)
or governor, line pressure
is low in "D", "2" or
"1" range but is normal in "R" range.
If oil leaks at or around low and reverse brake
circuit, line pressure becomes low in
"R" or
"P" range but IS normal in "D", "2" or "1"
range.
3) When line pressure is high, pressure regulator
valve may have stuck
Cutdown point
The cut-down point indicates
a point where line
pressure changes from high to low value.
Before proceeding cut-down testing, make sure
that line pressure "At Idle" and "At
Stall'' is
normal
Install vacuum gauge
VG30E engine without turbo
28 - 37
o(o'o) I (17-231 I 900- 1,200
12.22
(7 - 14) I 400-700 (-100. -133 -3 94) I
VG30E turbo engine
+467 I 29 - 39 1,200- 1,600 (+350, +13 78) (18 - 24)
13.23
(-200,
-267 -7 871 I (8. 14) 400 - 800
Judgment by cut-down testing
(1) When cut-down point disappears, the problem
Sticking pressure modifier valve
Sticking governor valve
Oil leaks at oil passage
(2) When cut-down point is too low or too high,
the problem may be due to
Incorrect springs (at pressure modifier valve
or governor valve)
Oil leaks at oil passage
may be due to
AT-92

SERVICE DATA AND SPECIFICATIONS (S.D.S.)
General Specifications
X8075 Engine model ~ I VG30E t VG30Eiurbo X8006 -
Autamatictranrmirrion model I E4N71B I 4N71B ~~
Stall torque ratlo
Transmission gear ratio
1st
2nd
TOP OD
Reverse
Recommended 011
1 X8075 1 X8006 Tianrmwon model code
number ~
20 1
2 458
1458
1000
0 686
2 182
Aurornar~c lranmwon fluid 'oexro" type
2 0 IO 0791
Oil capacity
2 2 (0 0871
7 0 hferr
17-3/8 US qt, 6-1/8 Imp qtl
5 6 (0 220)
5 8 (0 2281
6 0 (0 2361 6 2 IO 2441
6 4 10 2521
6 6 10 2601 6 8 (0 2681
7 0 (0 2761
--Specifications and Adjustment,
31567-XZ903
31567-XZ904
31567-XZ905
31567-XZ906
31507-X86W
31507-X8601
31537-XZ800
31537-XZ801
Tr.msmirrmn model code number
Torque converter assembly
Srarnped mark on the
torque COnYerter
Number of drive plates
Number of driven plates
Clearance rnm Ion1
Standard Allowable limit
Drive plate thickness mm (in1
Standard
Allowable limit
Thlcknesr of retamng
Dlate
1 GC GK
1 50 1 65 (0 0591 .O 06501
1 4 (0 0551
Thickness I numbel Part
mrn Iml
Thickness number
AT-95