NISSAN 300ZX 1984 Z31 Body Repair Manual

SEAT
Front Driver Seat (Cont'd)
Air diagram
AN make
tl if hose mnnemon IS disconnected, apply sealant to hoseconnection to prevent air leakage [@ portion onlv) Install each valve ~n Its proper PoSltlOn
[Yellow marking)
Onewav valve
@ sealant portion
SBF392B
BF-51

SEAT
Front Driver Seat (Cont'd)
POWER SEAT
12 151
SBF3878
BF-52

t IGNITION SWITCH I ON or START
IGNITION RELAY 35M
Big;
(For power window and
CIRCUIT
BREAKER
power seat)
To engine room harness L (Ground1
!
t B
,,-CIRCUIT BREAKER
M [ I
r CIRCUIT BREAKER SEAT SWITCH ~~ (Seat Ilfter. sllde. reclining and
thigh support1
Seat cushion ground
- CIRCUIT BREAKER
in harness
LD m ll W (D W m
SEAT BACK SWITCH
RTR AIR PUMP MOTOR
Seat cushion ground
IRiI
CIRCUIT BREAKER Seat curhian ground -

SEAT
Front Driver Seat (Cont'd)
Air diagram
Lumbar support
Thigh support switch
e
If hose connection 1s disconnected, apply sealant to hose
connection to prevent air leakage I@ portion only) Be sure air pump 1s free from dust. foreign substance, etc
Install safety valve in Its proper direction
Air pump operates only when each swjtch IS turned ON
@ Sealant portion
SBF394B
BF-54

SEAT
Front Assist Seat
Basically, this seat is the same as manual type front driver seat 2 + 2 seater model differs from manual
type front
seat in that walk-in mechanism has been added to it Refer to the description on manual
type driver
seat except for walk-in mechanism
WALK-IN MECHANISM
Release lever
a
Release wire assembly
Release wire adjustment Push down reclining device lever so there IS no play, then adlust the release wire
Releare wme assembly
TO (Seat release back lever frame) Mw
Walk-on wve adjustment When assembling, make sure - there 1s no play left SBF47OB
BF-55

SEAT
Rear Seat
Striker eat back hinge
N rn (kg-m. ft-lbl
SBF395B
BF-56

SEAT BELT
Refer to MA section for installation of seat belts.
GLL model has been equipped with seat belts with tension reducer This unit reduces the force required
to pull out seat belt while in use, and lessens pressure on the shoulder and hips for greater comfort
TENSION REDUCER WIRING DIAGRAM
IGNITION SWITCH I ON or ST
TENSION REDUCER-Assist
FUSE BLOCK
@
U
SEAT BELT SWITCH-Assist Iinrjde retractor1 (Main harness1
TENSION REDUCER-Driver (Inside retractor)
SEAT BELT SWITCH-Drwer IM~I~ IPower
harness1 To rime control unit (Seat belt warning lamp1
To engine room harness (Ground)
__ seat cushion ground
TENSION REDUCE OPERATION
SBF439B
Fully Seat belt stroke Fully retraned pulled out SBFMOE

TRIM AND MOLDING
When removlng clip or fastener, refer to CLIP & FASTENER
When handllng trim or molding, do not use excessive force and take care not to damage them.
inside Trim
SIDE, LUGGAGE AND FLOOR TRIM
1
BF-58

TRIM AND MOLDING
Inside Trim (Cont’d)
ROOF TRIM
Front portion
I LRmf trim
Rear portion
BF-59

TRIM AND MOLDING
Exterior
Apply sealing compound where necessary while installing parts
When applying sealing compound, be careful that the sealing compound does not protrude from parts
@ Side guard molding
Side guard molding is affixed to body panel
with sealant. And
the repair part is affixed with
double-faced adhesive tape.
Remove
it only if it is necessary to do so. e
1
Remova I :
Heat molding portion to 30 to 40°C (86 to
104'F) with
a heat gun
SBF455A
2
Installation
1 Remove all traces of bonding agent from
body panel. Then clean contact face
of body.
2 Heat body panel and molding to 30 to 40°C
(86 to 104°F) with a heat gun Then install
molding
Raise end of molding and, while cutting off
bonding agent, detach molding.
0 T-bar roof
SBF386B
@ Door molding
ve, draw out molding by upper ride of molding
SBF397B
0.0 Door weatherstrip and body side weatherstrip
while inslalling the weathemrip
SBF398B
BF-60