NISSAN 300ZX 1984 Z31 Body Manual PDF
Manufacturer: NISSAN, Model Year: 1984, Model line: 300ZX, Model: NISSAN 300ZX 1984 Z31Pages: 77, PDF Size: 1.97 MB
Page 71 of 77
BODY ALIGNMENT
All dimensions indicated in figures are actual ones.
When
a tram tracking gauge is used, adjust both pointers to equal length and check the pointers and
gauge itself to make sure there
is no free play.
When
a measuring tape IS used, check to be sure there IS no elongation, twisting or bending.
Measurements should be taken
at the center of the mounting holes.
An asterisk
(*) following the value at the measuring point indicates that the measuring point on the
other side
is symmetrically the same value.
Measurement points
The coordinates of
the measurement points are the distances measured from the respective dimension
lines in the directions of
"x", "y" and "2".
Dimension lines: "x" line - Center line of vehicle
"y" line - Center line of front axle (Any measurement point in front of the dimen-
sion line refers to
a minus "-" value.)
"2" line - Datum line (Any measurement point under the dimension line refers to
a minus "-" value.)
Engine Compartment
MEASUREMENT
____
BF-71
Page 72 of 77
BODY ALIGNMENT
Engine Compartment (Cont’d)
MEASUREMENT POINTS
Points Hole dia
mm (in) Detailed points Coordinates mm (in)
“X” I, I, 2
540 5
(21 28) -
653 0
(2571)
26 a
(1 0551 -
-325 0
1-12 ao)
Hole for front suspension upper mounting (Outside front
hole) 919 0
(36 1 a)
852 0
(33 54)
490 0
(1 9 29)
490 0
(19 29)
966 0
(38 03)
12 (047)
9 (0 35)
5 4 (0 213)
a (0 31 )
IH
bumper rubber
SBF421B
Hole for fixing front
fender
Hole for fixing har-
ness clip
at upperside
of front side member 395 0
(15 55)
460 0
:-1811l
strut tower
Hole for fixing har-
ness clip
at upperside
of front side member 395 0
(15 55)
100 0
(3 941
Front ride member 1 SBFd23B
Hole for mounting
hood hinge 640 0
(25 20)
500 0
(19 69) 11 (043)
SB F 4248
BF-72
Page 73 of 77
BODY ALIGNMENT
Engine Compartment (Cont'd)
Points Hole dia
mm (in1
7 (0 281
16 (0 631
Detailed points
FR 5BF425E
r Hood bumDer
Hole for mounting
wiper pivot
Hole for mounting
hood bumper rubber
on headlamp side
housing
Coordinates mm (in1 -
"X"
00
(01
320 0
(1 2 60)
-
"Y"
520 8
(20 501
-566 1
(-22 291
"2"
959 0
(37 761
BF-73
Page 74 of 77
BODY ALIGNMENT
Underbody
MEASUREMENT
SB F4268
BF-74
Page 75 of 77
BODY ALIGNMENT
Underbody (Cont’d)
MEASUREMENT POINTS
& e
Y
BF-75
Page 76 of 77
BODY ALIGNMENT
Underbody (Cont'd)
Coordinates mm (in) Hole dia
rnm (in)
13(051)
15 (0 59)
18 (071)
13 (051)
Detailed points Points
"X" "V"
Hole for front air
spoiler mounting 385 0
(15 161
-585 0
(-23 03)
388 0
(1 5 28)
Hole for water
drainage 380 0
(14 961
435
0
(17 131
255
0
(1004)
-
-
251 5
(9 90)
750
0
129 53)
1,500 0
(59 06)
361 6
114 24)
263
6
(10 38)
261
0
(10 28)
2 seater
model
2,800
0
(11024)
2+2 seater
model
3,000
0
(11811)
Hole for locating
418 5
(16 48) 528 8
(20 82) 00 13 (0 51 At under ride of member
2 seater
model
3,060
0
(120 47)
!+2 seater
model
3,260
0
(1 28 35)
Hole for rear
bumper mounting 418 5
(1648) 523 8
(20 62) 15 (0 59)
13(051)
SBF427E
FR
c3
SBF428E
r Front side member
Hole for mounting
tension rod bracket
on underside of
front crossmember
271 0
(1067)
-
400 0
I1 5 751
-465.0
(-1831)
-10 0
(-0 394)
325 5
(1281)
422 0
(16.61)
Hole for locating on
front suspension
member mounting
portion
(Underside of front
side member)
00 16 (0 63)
BF-76
Page 77 of 77
BODY ALIGNMENT
Underbody (Cont'd)
Points Hole dia
mm (in) Coordinates mm (in) Detailed points
"X" "Y'' I, I, z
510 a
(20 11 I -
489 1
(1926)
-
460 0
(1811)
80 0
(3 150)
912 6
(35 93) Front suspension
upper mounting
-
32 3 (3 240
54 (2 13)
15 (0 59)
2 seater
model
2,450 2
(96 46)
2+2 seatei
model
2,650 2
(104 34)
2 seater
model
1,930 0
2+2 seater
model
2,130 0
(75 98)
(a3 86)
Rear suspension
shock absorber
upper mounting a83 o
(34 76)
402 0
(1 5 83)
SBF43OE
Hole for locating on
underside of member
2 seater
model
1,900 0
2+2 seater
model
2,100 0
(74 ao)
182 68)
640 0
(25 20)
-
74 0
(2 913)
404 0
(1591) 00 13 (051)
SBF431E
2 seater
model
2.497 5
212 seater
model
2,697 5
(106 201
(98 33) 545 0
(21 46)
Hole for mounting
final drive on
underside of final
drive mounting
crossmember
15 (0 59)
2 seater
model
2,497 5
2+2 seater
model
2,697 5
(106
20)
(98 33) 69 0
(2 717)
545 0
(21 46) Final drive rnountmg brackel
FR SBF432E
BF-77