roof NISSAN 300ZX 1984 Z31 Body Workshop Manual

BODY
I
SECTION BF
CONTENTS
GENERAL SERVICING . . ............ .... ..... BF- 2
BODY END AND DOOR .. ...... .......... BF- 6
INSTRUMENT
........ ........ ..... . . BF-49
SEAT
... .. ........ .. ..... . BF-50
SEAT BELT
. .... ... ......... . . BF-57
TRIM AND MOLDING
.. ... .. . . BF-58
WINDSHIELD AND WINDOWS
...... ... .............. BF-63
T-BAR ROOF
........ ...... .. ......... BF-68
MIRROR
...... ... ... .. .... .. . . BF-69
REAR COMBINATION LAMP
........ .............. BF-70
BODY ALIGNMENT
.... ..... ... ... BF-71

TRIM AND MOLDING
Inside Trim (Cont’d)
ROOF TRIM
Front portion
I LRmf trim
Rear portion
BF-59

TRIM AND MOLDING
Exterior
Apply sealing compound where necessary while installing parts
When applying sealing compound, be careful that the sealing compound does not protrude from parts
@ Side guard molding
Side guard molding is affixed to body panel
with sealant. And
the repair part is affixed with
double-faced adhesive tape.
Remove
it only if it is necessary to do so. e
1
Remova I :
Heat molding portion to 30 to 40°C (86 to
104'F) with
a heat gun
SBF455A
2
Installation
1 Remove all traces of bonding agent from
body panel. Then clean contact face
of body.
2 Heat body panel and molding to 30 to 40°C
(86 to 104°F) with a heat gun Then install
molding
Raise end of molding and, while cutting off
bonding agent, detach molding.
0 T-bar roof
SBF386B
@ Door molding
ve, draw out molding by upper ride of molding
SBF397B
0.0 Door weatherstrip and body side weatherstrip
while inslalling the weathemrip
SBF398B
BF-60

TRIM AND MOLDING
Exterio
@ Back door upper molding
Back door panel
SBF405B
0 Back door side molding
, Glass-
Sidemolding // 1
Screw
Molding gromrne? J Back door panel
SBF406B
@ Back door lower molding
Attach the molding to the glass before install-
ing the glass.
Glass, /
SBF4078 Sealant
Cont'd)
@ T-bar roof sash and T-bar roof side molding
They are part of the T-bar roof glass and cannot be
removed (Refer to T-bar
Roof)
If they
are damaged, you should replace entire
T-bar roof glass assembly
@I T-bar roof weatherstrip
T-bar roof glass T-bar roof 7
T-bar roof ' weatherstrlp'
0 T-bar roof side weatherstrip
T-bar roof glaSS
T-bar roof side weatherstrq
- T-bar roof
T-bar roof ride
weatherstrip
Always adjust if it is not
sufficiently watertight
SBF436B
BF-62

T-BAR ROOF
Handle T-bar roof glass wlth care so not to damage It.
Apply sealant to portlons susceptible to water leakage If necessary
Side molding, sash, lock basement and
glass of T-bar roof constitute one unit and cannot be disas-
sembled.
T-bar roof female lock adJUStmen1 Front Rea' Female lock fron
Air deflector A
T-bar roof garnish -
I I
T-bar roof glass assembly '/Y'o / Drain hose Be careful not to twist or distort ho- T-bar roof weatherstrip
_t-
SBF437B T-bar roof shade
Drain (Drained beween pillar lower and front
Grease UP point
@ Sealant point
BF-68