oil NISSAN 300ZX 1984 Z31 Front Suspension Workshop Manual

FRONT SUSPENSION - Spring and Strut Assembly
I nspl
Wash all parts, except for nonmetallic parts,
clean with suitable solvent and dry with com-
pressed air.
a Blow dirt and dust off of nonmetallic parts
using compressed air
a. Oil oozing out around gland packing does not
call for strut replacement.
If oil leakage
is evident on spring seat, check
piston rod and gland packing to correct
the
cause of problem.
If oil leakage occurs on welded portion of
outer strut
casing, replace strut assembly.
b. If shock absorber itself is malfunctioning,
replace
as shock absorber kit (including piston
rod, cylinder, bottom
valve and guide bushing).
INNER CYLINDER AND OUTER CASING
a Inspect inner cylinder and outer casing for
cracks, deformation or other damage. For inner
cylinder damage, replace shock absorber. For
outer casing damage, replace strut assembly
Inner diameter:
Inner cylinder
32 0.32 1 mm (1.260 - 1 264 in)
n
SFA136
Maximum runout.
Inner cylinder
Less than 0.2 mm (0.008 in)
LCylinder
SFA137
PISTON ROD
a Inspect piston rod for cracks, deformation or
other damage Replace shock absorber, if
necessary Inspect threads for cracks or other damage
Replace shock absorber, if necessary.
Rod diameter:
Maximum runout
a
21.78 - 21.94 mm (0.8575 - 0.8638 in)
Less than 0.1 mm (0.004 in)
To'ai gauge R

SFA137 Piston rod
STRUT MOUNTING INSULATOR
Replace if cemented rubber-to-metal portion are
melted or cracked. Rubber parts should also be
replaced, if deteriorated.
STRUT MOUNTING BEARING
Replace if inspection reveals abnormal noise or
excessive rattle in axial direction
FA-8

FRONT SUSPENSION - Spring and Strut Assembly
c _. _.
e 78i8.581 .
: +
0
59 16,431
Assc
Before assembly, keep away from dust to prevent
entry of dust.
Use "NISSAN GENUINE STRUT FLUID" or
equivalent.
Oil capacity
is very important since performance of
strut varies with amount of fluid in strut.
Add correct amount of fluid
Capacity:
270 me (9 1 US fl oz,9.5 Imp fl 02)
__
Lubricate sealing lip of gland packing.
Ea
Install gland packing
Be careful not to damage sealing lip.
FA065
SFA141
Tighten gland packing
ST35652000l 1-1
rTnrque wrench c
lo^, m-I-L m iftJd 10 3ftl
N m Ikg-m,ft-lbl
SFAS91
rn
I I1 01 I1 51 1201 (ftl
L Length of torque wrench
SFA144
FA-9

TRANSVERSE LINK AND LOWER BALL JOINT
Removal ar
Separate knuckle arm from tie-rod using Tool.
SFA575
Separate knuckle arm from strut. Remove
stabilizer, tension rod and transverse link
SFA576
Separate ball joint from knuckle arm using
press
SFA577
Installation
To install transverse link, first temporarily
tighten nuts securing transverse
link spindle
which connects transverse
link to suspension
cross member.
Final tightening should be carried out at curb
weight with tires
on ground.
Make sure mating surface of bushing
is clean
and free from oil and grease.
FA-I 2

ADJUSTABLE SHOCK ABSORBER
-Removal and Installation (Cont'dL
0 Connect sub-harness to connector within
piston rod using guide
Be careful not to
damage connector.
SRA469
Disassembly
Avoid dirt and dust getting inside strut
0 Remove coil spring Refer to Front Suspension
0 Remove gland packing Refer to Front Suspen-
(Spring and Strut Assembly)
sion (Spring and Strut Assembly)
Inspection
Refer to Front Suspension (Spring and Strut
Assembly)
0 Carefully insert the shock absorber cartridge
into the outer strut tube.
CAUTION:
Do not drop the shock absorber or otherwise
mishandle
it.
SFA165
After the shock absorber has been inserted
into the outer tube, gently shake the strut
assembly right and left
so that the shock
absorber
is centered.
Install gland packing and tighten the gland
packing with the Gland Packing Wrench and
a torque wrench
Refer to Spring and Strut Assembly for assembly
Be careful not to damage the piston rod during
tightening.
ST35652000- I-) SFA591
Further steps are the same procedure as the
conventional strut assembly Refer to Spring
and Strut Assembly for assembly
FA-I 6

SERVICE DATA AND SPECIFICATIONS (S. D.S.)
General Specifications
VG30ET
Vehicle model 2 seater 2+2 seater
GL GL-L
VG30E
2 seater 2+2 seater
SF GL GL-L GL GL-L
13 5 (05311 ~ ~~
~~
Coil diameter mm (in1 170 (6 691
Free length mm (~nl
strut
TYDe I Gasfilled double acting hydraulic
293 5 (11 56) 3000lll811 293 5 (1 1 561 300 0 (1 1 81 1 306 0 (12 051
Double acting hydraultc
Red x 1, White x 1 ldentlflcat8an color
I Adptable I Non-adlustable
Yellow x 1, fled x 1. Yellow x 1, Whm x 1, White x 1 White x 1 White x 1 White x 1
lnnter cvlmder Inner diameter
Stroke mm Iinl
Damping force [at 0 3 m (1 0 ft)/rec 1
Maxtmum/Minimum ~~
~
mm Iin) 350-35 1 (1 378- 13821
191 8 17 5511131 8 I1 2521
Ftrm Normal Soft ~~ ~
~
32 0 - 32 1 (1 260 - 1 2641
(kg'lb' Expansion
Less than 0 2 (0 008) Less than 0 2 (00081 I Maximum runout mm (in1 1
981 1100, 221) 1.510 1,226 530
(154,3401 (125,2761 (54. 1191
Piston rod
Rod diameter
785
(80. 1761 N Ikg, Ib) Compression
mm (ml 25 (0 981 I 22 10 87)
441 (45.991 637 255
(65. 1431 (26. 571
Maxmum runout mm (in1 I Less than 0 1 10 0041 I Less than 0 1 10 0041
Stabilizer bar diameter mm (In) I 22 (0 871
Tension rod diametei mm (in) I 181071)
FA-22