brake sensor NISSAN NAVARA 2005 Repair User Guide

TROUBLE DIAGNOSIS
AT-45
D
E
F
G
H
I
J
K
L
MA
B
AT
4. Securely engage the parking brake so that the tires do not turn.
5. Start the engine, then measure the line pressure at both idle and
the stall speed.
CAUTION:
lKeep the brake pedal pressed all the way down during
measurement.
lWhen measuring the line pressure at the stall speed.
Refer toAT-43, "
STALL TEST".
6. After the measurements are complete, install the oil pressure
detection plug and tighten to the specified torque. Refer toAT-
251, "Components".
CAUTION:
lDo not reuse O-ring.
lApply ATF to O-ring.
Line Pressure
Judgement of Line Pressure Test
SAT513G
SAT493G
Engine speedLine pressure [kPa (bar, kg/cm
2,psi)]
“R” position “D” position
At idle speed 425 - 465 (4.3 - 4.6, 4.3 - 4.7, 62 - 67) 379 - 428 (3.8 - 4.3, 3.9 - 4.4, 55 - 62)
At stall speed 1,605 - 1,950 (16.0 - 19.5, 16.4 - 19.9, 233 - 283) 1,310 - 1,500 (13.1 - 15.0, 13.4 - 15.3, 190 - 218)
Judgement Possible cause
Idle speedLow for all positions
(“P”, “R”, “N” and “D”)Possible causes include malfunctions in the pressure supply system and low oil pump output.
For example
lOil pump wear
lPressure regulator valve or plug sticking or spring fatigue
lOil strainer
oil pump
pressure regulator valve passage oil leak
lEngine idle speed too low
Only low for a specific
positionPossible causes include an oil pressure leak in a passage or device related to the position
after the pressure is distributed by the manual valve.
HighPossible causes include a sensor malfunction or malfunction in the line pressure adjustment
function.
For example
lAccelerator pedal position signal malfunction
lA/T fluid temperature sensor malfunction
lLine pressure solenoid malfunction (sticking in OFF state, filter clog, cut line)
lPressure regulator valve or plug sticking

TROUBLE DIAGNOSIS
AT-53
D
E
F
G
H
I
J
K
L
MA
B
AT
Symptom ChartECS00FX8
lThe diagnostic item numbers show the sequence for inspection. Inspect in order from item 1.
lOverhaul and inspect inside the A/T only if A/T fluid condition is NG. Refer toAT-43, "A/T Fluid Con-
dition Check".
No. Items Symptom Condition Diagnostic ItemReference
page
1
Shift
ShockLarge shock. (“N”®“D”
position)
Refer toAT-180,
"Large Shock (“N”to
“D”Position)".ON vehicle1. Engine idle speedEC-38
2. Engine speed signalAT-108
3. Accelerator pedal position sensorAT- 11 6
4. Control cable adjustmentAT- 2 11
5. A/T fluid temperature sensorAT- 11 8
6. ATF pressure switch 1 and front brake solenoid valveAT-156,
AT-137
7. CAN communication lineAT- 9 1
8. A/T fluid level and stateAT- 4 3
9. Line pressure testAT- 4 4
10. Control valve with TCMAT-218
OFF vehicle11. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer toAT- 1 4 , "Cross-
Sectional View (2WD Models)",AT- 1 5 , "Cross-Sectional View
(4WD Models)".)AT-263
2Shock is too large
when changing D1
®D2.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 5 and direct clutch solenoid valveAT-160,
AT-142
4. CAN communication lineAT- 9 1
5. Engine speed signalAT-108
6. Turbine revolution sensorAT-123
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT-218
OFF vehicle 10. Direct clutchAT-298
3Shock is too large
when changing D2
®D3.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 6 and high and low reverse clutch
solenoid valveAT-162,
AT-147
4. CAN communication lineAT- 9 1
5. Engine speed signalAT-108
6. Turbine revolution sensorAT-123
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT-218
OFF vehicle 10. High and low reverse clutchAT-296

AT-54
TROUBLE DIAGNOSIS
4
Shift
ShockShockistoolarge
when changing D3
®D4.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 5 8,
AT- 1 3 2
4. CAN communication lineAT- 9 1
5. Engine speed signalAT- 1 0 8
6. Turbine revolution sensorAT- 1 2 3
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT- 2 1 8
OFF vehicle 10. Input clutchAT- 2 8 6
5Shockistoolarge
when changing D4
®D5.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 6,
AT- 1 3 7
4. CAN communication lineAT- 9 1
5. Engine speed signalAT- 1 0 8
6. Turbine revolution sensorAT- 1 2 3
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT- 2 1 8
OFF vehicle10. Front brake (brake band)AT- 2 5 111. Input clutchAT- 2 8 6
6Shockistoolargefor
downshift when accel-
erator pedal is
pressed.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. CAN communication lineAT- 9 1
4. Engine speed signalAT- 1 0 8
5. Turbine revolution sensorAT- 1 2 3
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
7. A/T fluid level and stateAT- 4 3
8. Control valve with TCMAT- 2 1 8
OFF vehicle9. Front brake (brake band)AT- 2 5 110. Input clutchAT- 2 8 6
11. High and low reverse clutchAT- 2 9 6
12. Direct clutchAT- 2 9 8
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-55
D
E
F
G
H
I
J
K
L
MA
B
AT
7
Shift
ShockShock is too large for
upshift when accelera-
tor pedal is released.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. Engine speed signalAT-108
4. CAN communication lineAT- 9 1
5. Turbine revolution sensorAT-123
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
7. A/T fluid level and stateAT- 4 3
8. Control valve with TCMAT-218
OFF vehicle9. Front brake (brake band)AT-25110. Input clutchAT-286
11. High and low reverse clutchAT-296
12. Direct clutchAT-298
8Shock is too large for
lock-up.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. Engine speed signalAT-108
4. CAN communication lineAT- 9 1
5. Turbine revolution sensorAT-123
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
7. Torque converter clutch solenoid valveAT- 11 0
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT-218
OFF vehicle 10. Torque converterAT-263
9Shock is too large dur-
ing engine brake.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. CAN communication lineAT- 9 1
4. A/T fluid level and stateAT- 4 3
5. Control valve with TCMAT-218
OFF vehicle6. Front brake (brake band)AT-2517. Input clutchAT-286
8. High and low reverse clutchAT-296
9. Direct clutchAT-298
No. Items Symptom Condition Diagnostic ItemReference
page

AT-56
TROUBLE DIAGNOSIS
10
No Up
ShiftGear does not change
from D
1®D2or from.
Refer toAT-188, "
A/T
Does Not Shift: D1®
D2".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 0,
AT- 1 4 2
4. Line pressure testAT- 4 4
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT- 2 1 8
OFF vehicle 7. Direct clutchAT- 2 9 8
11Gear does not change
from D2®D3or from.
Refer toAT-190, "
A/T
Does Not Shift: D2®
D3".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. ATF pressure switch 6 and high and low reverse clutch
solenoid valveAT- 1 6 2,
AT- 1 4 7
4. Line pressure testAT- 4 4
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT- 2 1 8
OFF vehicle 7. High and low reverse clutchAT- 2 9 6
12Gear does not change
from D
3®D4or from.
Refer toAT-192, "
A/T
Does Not Shift: D3®
D4".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 5 8,
AT- 1 3 2
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 6,
AT- 1 3 7
5. Line pressure testAT- 4 4
6. CAN communication lineAT- 9 1
7. Control valve with TCMAT- 2 1 8
OFF vehicle 8. Input clutchAT- 2 8 6
13Gear does not change
from D
4®D5or from.
Refer toAT-194, "
A/T
Does Not Shift: D4®
D5".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Overdrive control switchAT- 1 7 2
3. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 6,
AT- 1 3 7
5. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 0,
AT- 1 4 2
6. Turbine revolution sensorAT- 1 2 3
7. Line pressure testAT- 4 4
8. CAN communication lineAT- 9 1
9. Control valve with TCMAT- 2 1 8
OFF vehicle10. Front brake (brake band)AT- 2 6 311. Input clutchAT- 2 8 6
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-57
D
E
F
G
H
I
J
K
L
MA
B
AT
14
No Down
ShiftIn “D” position, does
not downshift to 4th
gear.
Refer toAT-200, "A/T
Does Not Shift: 5th
Gear®4th Gear".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
3. ATF pressure switch 1 and front brake solenoid valveAT-156,
AT-137
4. ATF pressure switch 5 and direct clutch solenoid valveAT-160,
AT-142
5. CAN communication lineAT- 9 1
6. Line pressure testAT- 4 4
7. Control valve with TCMAT-218
OFF vehicle8. Front brake (brake band)AT-2639. Input clutchAT-286
15In “D” or “3” position,
does not downshift to
3rd gear.
Refer toAT-202, "A/T
Does Not Shift: 4th
Gear®3rd Gear".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
3. ATF pressure switch 3 and input clutch solenoid valveAT-158,
AT-132
4. ATF pressure switch 1 and front brake solenoid valveAT-156,
AT-137
5. CAN communication lineAT- 9 1
6. Line pressure testAT- 4 4
7. Control valve with TCMAT-218
OFF vehicle 8. Input clutchAT-286
16In “D” or “2” position,
does not downshift to
2nd gear.
Refer toAT-203, "A/T
Does Not Shift: 3rd
Gear®2nd Gear".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
3. ATF pressure switch 6 and high and low reverse clutch
solenoid valveAT-162,
AT-147
4. CAN communication lineAT- 9 1
5. Line pressure testAT- 4 4
6. Control valve with TCMAT-218
OFF vehicle 7. High and low reverse clutchAT-296
17In “D” or “1” position,
does not downshift to
1st gear.
Refer toAT-204, "A/T
Does Not Shift: 2nd
Gear®1st Gear".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
3. ATF pressure switch 5 and direct clutch solenoid valveAT-160,
AT-142
4. CAN communication lineAT- 9 1
5. Line pressure testAT- 4 4
6. Control valve with TCMAT-218
OFF vehicle 7. Direct clutchAT-298
No. Items Symptom Condition Diagnostic ItemReference
page

AT-58
TROUBLE DIAGNOSIS
18
Slips/Will
Not
EngageWhen “D” position,
remains in 1st gear.ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. Direct clutch solenoid valveAT- 1 4 2
4. Line pressure testAT- 4 4
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT- 2 1 8
OFF vehicle7. 3rd one-way clutchAT- 2 8 4
8. 1st one-way clutchAT- 2 9 1
9. Gear systemAT- 2 5 1
10. Reverse brakeAT- 2 6 3
11. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer toAT-
14, "Cross-Sectional View (2WD Models)",AT- 1 5 , "Cross-
Sectional View (4WD Models)".)AT- 2 6 3
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer toAT-14, "
Cross-
Sectional View (2WD Models)",AT-15, "Cross-Sectional View
(4WD Models)".)AT- 2 6 3
19When “D” position,
remains in 2nd gear.ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. Low coast brake solenoid valveAT- 1 5 2
4. Line pressure testAT- 4 4
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT- 2 1 8
OFF vehicle7. 3rd one-way clutchAT- 2 8 4
8. Gear systemAT- 2 5 1
9. Direct clutchAT- 2 9 8
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer toAT-14, "
Cross-
Sectional View (2WD Models)",AT-15, "Cross-Sectional View
(4WD Models)".)AT- 2 6 3
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-59
D
E
F
G
H
I
J
K
L
MA
B
AT
20
Slips/Will
Not
EngageWhen “D” position,
remains in 3rd gear.ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
3. Line pressure testAT- 4 4
4. CAN communication lineAT- 9 1
5. Control valve with TCMAT-218
OFF vehicle6. 3rd one-way clutchAT-284
7. Gear systemAT-251
8. High and low reverse clutchAT-296
9. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer toAT-
14, "Cross-Sectional View (2WD Models)",AT- 1 5 , "Cross-
SectionalView(4WDModels)".)AT-263
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer toAT- 1 4 , "
Cross-
Sectional View (2WD Models)",AT- 1 5 , "Cross-Sectional View
(4WD Models)".)AT-263
21When “D” position,
remains in 4th gear.ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
3. ATF pressure switch 3 and input clutch solenoid valveAT-158,
AT-132
4. ATF pressure switch 5 and direct clutch solenoid valveAT-160,
AT-142
5. ATF pressure switch 6 and high and low reverse clutch
solenoid valveAT-162,
AT-147
6. Low coast brake solenoid valveAT-152
7. Front brake solenoid valveAT-137
8. Line pressure testAT- 4 4
9. CAN communication lineAT- 9 1
10. Control valve with TCMAT-218
OFF vehicle11. Input clutchAT-28612. Gear systemAT-251
13. High and low reverse clutchAT-296
14. Direct clutchAT-298
No. Items Symptom Condition Diagnostic ItemReference
page

AT-60
TROUBLE DIAGNOSIS
22
Slips/Will
Not
EngageWhen “D” position,
remains in 5th gear.ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 6,
AT- 1 3 7
4. Line pressure testAT- 4 4
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT- 2 1 8
OFF vehicle7. Front brake (brake band)AT- 2 6 38. Input clutchAT- 2 8 6
9. Gear systemAT- 2 5 1
10. High and low reverse clutchAT- 2 9 6
23Vehicle cannot be
started from D
1.
Refer toAT-186, "
Vehi-
cle Cannot Be Started
from D1".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Accelerator pedal position sensorAT- 11 6
3. Line pressure testAT- 4 4
4. CAN communication lineAT- 9 1
5. Control valve with TCMAT- 2 1 8
OFF vehicle6. Torque converterAT- 2 6 3
7. Oil pump assemblyAT- 2 8 1
8. 3rd one-way clutchAT- 2 8 4
9. 1st one-way clutchAT- 2 9 1
10. Gear systemAT- 2 5 1
11. Reverse brakeAT- 2 6 3
12. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer toAT-
14, "Cross-Sectional View (2WD Models)",AT- 1 5 , "Cross-
Sectional View (4WD Models)".)AT- 2 6 3
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer toAT-14, "
Cross-
Sectional View (2WD Models)",AT-15, "Cross-Sectional View
(4WD Models)".)AT- 2 6 3
24Does not lock-up.
Refer toAT-196, "A/T
Does Not Perform
Lock-up".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Line pressure testAT- 4 4
3. Engine speed signalAT- 1 0 8
4. Turbine revolution sensorAT- 1 2 3
5. Torque converter clutch solenoid valveAT- 11 0
6. CAN communication lineAT- 9 1
7. Control valve with TCMAT- 2 1 8
OFF vehicle8. Torque converterAT- 2 6 39. Oil pump assemblyAT- 2 8 1
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-61
D
E
F
G
H
I
J
K
L
MA
B
AT25
Slips/Will
Not
EngageDoes not hold lock-up
condition.
Refer toAT-197, "A/T
Does Not Hold Lock-
up Condition".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Line pressure testAT- 4 4
3. Engine speed signalAT-108
4. Turbine revolution sensorAT-123
5. Torque converter clutch solenoid valveAT- 11 0
6. CAN communication lineAT- 9 1
7. Control valve with TCMAT-218
OFF vehicle8. Torque converterAT-2639. Oil pump assemblyAT-281
26Lock-up is not
released.
Refer toAT-199,
"Lock-up Is Not
Released".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Line pressure testAT- 4 4
3. Engine speed signalAT-108
4. Turbine revolution sensorAT-123
5. Torque converter clutch solenoid valveAT- 11 0
6. CAN communication lineAT- 9 1
7. Control valve with TCMAT-218
OFF vehicle8. Torque converterAT-2639. Oil pump assemblyAT-281
27No shock at all or the
clutch slips when vehi-
cle changes speed D1
®D2.ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
3. ATF pressure switch 5 and direct clutch solenoid valveAT-160,
AT-142
4. CAN communication lineAT- 9 1
5. Line pressure testAT- 4 4
6. Control valve with TCMAT-218
OFF vehicle7. Torque converterAT-263
8. Oil pump assemblyAT-281
9. 3rd one-way clutchAT-284
10. Gear systemAT-251
11 . D i r e c t c l u t c hAT-298
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer toAT- 1 4 , "
Cross-
Sectional View (2WD Models)",AT- 1 5 , "Cross-Sectional View
(4WD Models)".)AT-263
No. Items Symptom Condition Diagnostic ItemReference
page