battery NISSAN NOTE 2016 Service User Guide

AV
AUDIO UNITAV-53
< REMOVAL AND INSTALLATION > [BASE AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
REMOVAL AND INSTALLATION
AUDIO UNIT
Exploded ViewINFOID:0000000012432889
Removal and InstallationINFOID:0000000012432890
REMOVAL
1. Remove the negative battery cable. Refer to PG-70, "Removal and Installation (Battery)".
2. Remove cluster lid C. Refer to IP-22, "
Removal and Installation".
3. Remove the audio unit screws, then pull out the audio unit.
4. Disconnect the harness connectors from the audio unit and remove.
INSTALLATION
Installation is in the reverse order of removal.
1. Audio unit bracket (LH) 2. Audio unit 3. Audio unit bracket (RH)
AWNIA3121ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-62
< PRECAUTION >[DISPLAY AUDIO]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012432945
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Trouble DiagnosisINFOID:0000000012432946
AV COMMUNICATION SYSTEM
• Do not apply voltage of 7.0 V or higher to the measurement terminals.
• Use the tester with its open terminal voltage being 7.0 V or less.
• Be sure to turn ignition switch OFF and disconnect the battery cable from\
the negative terminal before checking the circuit.
Precaution for Harness RepairINFOID:0000000012432947
AV COMMUNICATION SYSTEM
• Solder the repaired parts, and wrap with tape. [Frays of twisted line
must be within 110 mm (4.33 in).]
PKIA0306E
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-76
< ECU DIAGNOSIS INFORMATION >[DISPLAY AUDIO]
AUDIO UNIT
ECU DIAGNOSIS INFORMATION
AUDIO UNIT
Reference ValueINFOID:0000000012432962
TERMINAL LAYOUT
PHYSICAL VALUES
AWNIA3652ZZ
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
2
(GR) 3
(P) Sound signal front door
speaker LH
Output ON Sound output
4
(W) 5
(R) Sound signal rear door
speaker LH
Output ON Sound output
6
(SB) 15
(G) Steering switch signal A Input ON Press SOURCE switch
0V
Press switch 1.0V
Press switch 2.0V
Press switch 3.0V
Except above 5.0V
7
(W) Ground ACC power supply
Input ACC—Battery voltage
9
(R) 8
(B) Illumination control signal Input ON Headlamps ON
Battery voltage
SKIB3609E
SKIB3609E
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
AUDIO UNITAV-77
< ECU DIAGNOSIS INFORMATION > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P11
(BG) 12
(V) Sound signal front door
speaker RH
Output ON Sound output
13
(L) 14
(Y) Sound signal rear door
speaker RH
Output ON Sound output
16
(V) 15
(G) Steering switch signal B Input ON Press switch
0V
Press switch 1.0V
Press switch 2.0V
Except above 5.0V
18
(LG) Ground Vehicle speed signal Input ON When vehicle speed is ap-
prox. 40 km/h (25 MPH)
19
(Y) Ground Battery power supply Input OFF
—Battery voltage
20
(B/W) Ground Ground
— ON— 0 V
33
(B) Ground Camera ground
— ON — 0 V
34
(L) Ground Camera power supply Output ON Camera image displayed
6.0 V
Except for above 0 V
35
(Y) 36
(Shield) Camera image signal Input ON Camera image displayed
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
JSNIA0012GB
SKIB2251J
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-78
< ECU DIAGNOSIS INFORMATION >[DISPLAY AUDIO]
AUDIO UNIT
37
(P) 39
(Shield) Microphone signal
Input ONWhile speaking into micro-
phone.
38
(L) Ground MIC VCC
Output ON—5 V
44
(B) Ground Camera detection
— ON— 0 V
46
(B) Ground EQ02 Ground
— ON— 0 V
48
(B/W) Ground EQ04 Ground
— ON— 0 V
50
(Y) Ground Reverse signal
Input ONSelector lever in R (re-
verse)
Battery voltage
Selector lever in any posi-
tion other than R (reverse) 0 V
53
(B) — USB ground
— —— —
55
(G) — USB D+ signal
— —— —
56
(W) — USB D
− signal — — — —
57
(R) — V BUS signal
— —— —
58
(Shield) — USB shield
— —— —
60
(G) Ground AUX jack audio signal LH Input ON Received audio signal
(AUX input)
61
(L) Ground AUX jack audio signal RH Input ON Received audio signal
(AUX input)
62
(Y) Ground AUX ground
— ON— 0V
67
(B) Ground Antenna amp. ON signal Output ON Audio unit ON, FM-AM se-
lected.
Battery voltage
68
(B) Ground AM/FM antenna signal Input ON
Audio unit ON, FM-AM se-
lected.5.0 V
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
POWER SUPPLY AND GROUND CIRCUITAV-95
< DTC/CIRCUIT DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
AUDIO UNIT
AUDIO UNIT : Diagnosis ProcedureINFOID:0000000012432967
Regarding Wiring Diagram information, refer to AV-80, "Wiring Diagram".
1.CHECK FUSE
Check that the following fuses are not blown.
Are the fuses blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M45.
3. Check voltage between audio unit connector M45 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M40.
3. Check continuity between audio unit connectors and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connectors.
Terminal No. Signal name Fuse No.
7 ACC power supply 18 (10A)
19 Battery power supply 29 (20A)
Audio unit
GroundCondition Vo l ta g e
(Approx.)
Connector Terminal
M45 7
—Ignition switch: ON
Battery voltage
19 Ignition switch: OFF
Audio unit
GroundContinuity
Connector Terminal
M45 20
—Y es
M40 44
46
48
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-100
< DTC/CIRCUIT DIAGNOSIS >[DISPLAY AUDIO]
REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT
REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT
Diagnosis ProcedureINFOID:0000000012432970
Regarding Wiring Diagram information, refer to
AV-80, "Wiring Diagram".
1.CHECK REVERSE INPUT SIGNAL
1. Turn ignition switch ON.
2. Shift the selector lever to R (reverse).
3. Check voltage between audio unit connector M40 and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2.CHECK CAMERA POWER SUPPLY CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M40 and rear view camera connector.
3. Check continuity between audio unit connecto r M40 and rear view camera connector D501.
4. Check continuity between audio unit connector M40 and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3.CHECK CAMERA POWER SUPPLY VOLTAGE
1. Connect audio unit connector M40 and rear view camera connector.
2. Turn ignition switch ON.
3. Shift the selector lever to R (reverse).
4. Check voltage between audio unit connector M40 and ground.
Is inspection result normal?
YES >> GO TO 4.
NO >> Replace audio unit. Refer to AV-113, "
Removal and Installation".
Audio unit Ground
Condition Vo l ta g e
(Approx.)
(+)
(−)
Connector Terminal
M40 50—Selector lever in R (re-
verse)
Battery Voltage
Audio unit
Rear view camera
Continuity
Connector TerminalConnector Terminal
M40 34D501 2Yes
Audio unit
GroundContinuity
Connector Terminal
M40 34 No
Audio unitGround
Condition Vo l ta g e
(Approx.)
(+)
(−)
Connector Terminal
M40 34—Selector lever is in “R”. 6.0 V
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
NORMAL OPERATING CONDITIONAV-111
< SYMPTOM DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000012432976
RELATED TO NOISE
The majority of the audio concerns are the result of outside causes (bad CD, electromagnetic interference,
etc.).
The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.
• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.
• Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the antenna at a different time from the waves which reflect off mountains or buildings.
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
Type of Noise and Possible Cause
RELATED TO HANDS-FREE PHONE
Occurrence condition Possible cause
Occurs only when engine is ON. A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.
• Ignition components
The occurrence of the noise is linked with the operation of the fuel pump. • Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating. A cracking or snapping sound occurs with the op-
eration of various switches.
• Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing. • Motor case ground
•Motor
The noise occurs constantly, not just under certain conditions. • Rear defogger coil malfunction
• Open circuit in printed heater
• Poor ground of antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially when
it is vibrating excessively. • Ground wire of body parts
• Ground due to improper part installation
• Wiring connections or a short circuit
Symptom
Cause and Counter measure
Does not recognize cellular phone connection (No connection is
displayed on the display at the guide). Some Bluetooth
® enabled cellular phones may not be recognized
by the in-vehicle phone module.
Refer to “RELATED TO HANDS-FREE PHONE (Check Compati-
bility)” in AV- 1 0 8 , "
Symptom Table".
Cannot use hands-free phone. Customer will not be able to use a hands-free phone under the fol-
lowing conditions:
• The vehicle is outside of the telephone service area.
• The vehicle is in an area where it is difficult to receive radio
waves; such as in a tunnel, in an underground parking garage,
near a tall building or in a mountainous area.
• The cellular phone is locked to prevent it from being dialed.
NOTE:
While a cellular phone is connected through the Bluetooth
® wire-
less connection, the battery power of the cellular phone may dis-
charge quicker than usual. The Bluetooth
® Hands-Free Phone
System cannot charge cellular phones.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
AUDIO UNITAV-113
< REMOVAL AND INSTALLATION > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
REMOVAL AND INSTALLATION
AUDIO UNIT
Exploded ViewINFOID:0000000012432977
Removal and InstallationINFOID:0000000012432978
REMOVAL
1. Remove the battery negative terminal. Refer to PG-70, "Removal and Installation (Battery)".
2. Remove cluster lid C. Refer to IP-22, "
Removal and Installation".
3. Remove the audio unit screws, the pull out the audio unit.
4. Disconnect the harness connectors from the audio unit and remove.
INSTALLATION
Installation is in the reverse order of removal.
1. Audio unit bracket (LH) 2. Audio unit 3. Audio unit bracket (RH)
AWNIA3579ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-126
< PRECAUTION >[NAVIGATION]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012432992
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Cautions in Removing Battery Terminal and AV Control Unit (Models with AV Control
Unit)
INFOID:0000000012432993
CAUTION:
Remove battery terminal and AV control unit 30 seconds or more after turning the ignition switch OFF.
NOTE:
After the ignition switch is turned OFF, the AV cont rol unit continues operating for approximately 30 seconds.
Therefore, data corruption may occur if battery voltage is cut off within 30 seconds.
Precaution for Trouble DiagnosisINFOID:0000000012432994
AV COMMUNICATION SYSTEM
• Do not apply voltage of 7.0 V or higher to the measurement terminals.
• Use the tester with its open terminal voltage being 7.0 V or less.
• Be sure to turn ignition switch OFF and disconnect the battery cable from\
the negative terminal before checking the circuit.
Precaution for Harness RepairINFOID:0000000012432995
AV COMMUNICATION SYSTEM
Revision: August 2015 2016 Versa Note

cardiagn.com