ECU NISSAN NOTE 2016 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 2163 of 3641
INT-12
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
1. Loose harness or harness connectors.
2. Front console map/reading lamp lens loose.
3. Loose screws at console attachment points.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of thes e incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component installed to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator installation pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine rpm or
load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2167 of 3641
INT-16
< REMOVAL AND INSTALLATION >
FRONT DOOR FINISHER
1. Remove door pull handle escutcheon using a suitable tool.
2. Remove screw (B) from power window and door lock/unlockswitch (RH) finisher.
3. Remove power window and door lock/unlock switch (RH) fin- isher (1) using a suitable tool (A).
: Pawl
4. Disconnect the harness connector from the pow er window and door lock/unlock switch (RH).
5. Remove front door finisher bolt (A).
6. Release clips using a suitable tool (A) and remove front door fin- isher as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing front door finisher, check that cl ips and pawls are securely placed into door panel
holes.
REMOVAL - MANUAL WINDOW
1. Remove door pull handle escutcheon using a suitable tool.
2. Remove screw, release pawls using a suitable tool and remove storage tray (LH/RH).
AWJIA1140ZZ
JMJIA6023ZZ
AWJIA1122ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2168 of 3641
FRONT DOOR FINISHERINT-17
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
3. Release the metal clip (A) behind the manual window crank han- dle using a suitable tool (B). Pull the manual window crank han-
dle (3) outward from the front door finisher and remove handle.
4. Remove manual window crank handle.
5. Remove front door finisher bolt.
6. Release clips using a suitable tool (A) and remove front door fin- isher as shown.
(B): Protective tape
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for defo rmation and damage during installation.
• When installing front door finisher, check that clips and pawls are securely placed into door panel
holes.
AWJIA1119ZZ
AWJIA1083ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2170 of 3641
REAR DOOR FINISHERINT-19
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
3. Remove screw (B) from power window and door lock/unlock switch (RH) finisher.
4. Remove power window and door lock/unlock switch (RH) fin- isher (1) using a suitable tool (A).
: Pawl
5. Disconnect the harness connector from the power window and door lock/unlock switch (RH).
6. Remove rear door finisher bolt (A).
7. Release rear door finisher clips using a suitable tool (A) and remove rear door finisher as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for defo rmation and damage during installation.
• When installing rear door finisher , check that clips and pawls are securely placed into door panel
holes.
REMOVAL - MANUAL WINDOW
1. Release rear door corner finisher clip using a suitable tool.
2. Remove screw, release storage tray pawls using a suitable tool and remove storage tray.
AWJIA1140ZZ
JMJIA6028ZZ
AWJIA1121ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2171 of 3641
INT-20
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
3. Release the metal clip (A) behind the manual window crank han-dle using a suitable tool (B). Pull the manual window crank han-
dle (3) outward from the front door finisher and remove handle.
4. Remove rear door finisher bolt (A).
5. Release rear door finisher clips using a suitable tool (A) and remove rear door finisher as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear door finisher, check that clips and pawls are securely placed into door panel
holes.
AWJIA1119ZZ
JMJIA6028ZZ
AWJIA1121ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2173 of 3641
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Pull front pillar finisher downward as shown to release the frontpillar finisher clip (bottom).
: Clip
: Pawl
3. Cut and discard front pillar finisher tether clips.
4. Remove the remaining piece of the tether clip (B) using a suit- able tool (A).
INSTALLATION
1. Install new front pillar finisher tether clips (A) to the front pillarfinisher by inserting clip end and rotating 90 degrees to fit.
CAUTION:
• Do not reuse tether clips. Replace with new part after
removal.
• Make sure to install tether clip to front pillar finisher before installing front pillar finisher.
• When installing tether clip to front pillar finisher, be sure to install by aligning to the cutout.
• Visually check the clip for deformation and damage dur-
ing installation. Replace with new one if necessary.
• When installing front pillar finisher, check that clip and
tether clips are securely placed into body panel holes.
2. Install the front pillar finisher to the front pillar.
KICKING PLATE
KICKING PLATE : Removal and InstallationINFOID:0000000012431866
FRONT KICKING PLATE
Removal
AWJIA1124ZZ
AWJIA1111ZZ
AWJIA1088ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2174 of 3641
BODY SIDE TRIMINT-23
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
1. Release front kicking plate pawls and metal clip using a suitable tool (A) and remove front kicking plate as shown.
: Pawl
: Metal clip
Installation
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for defo rmation and damage during installation.
• When installing front kicking plate, check that clips and pawls are securely placed into body panel holes.
REAR KICKING PLATE
Removal
1. Remove rear seat cushion. Refer to SE-41, "Seat Cushion".
2. Lift rear end of rear kicking plate to release metal clip, then rotate front end of rear kicking plate to release pawls and
remove.
: Pawl
: Metal clip
: Clip
Installation
Installation is in the reverse order of removal.
AWJIA1123ZZ
AWJIA1483ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2175 of 3641
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear kicking plate, check that clips and pawls ar e securely placed into body panel
holes.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and InstallationINFOID:0000000012431867
REMOVAL
1. Remove front kicking plate. Refer to INT-22, "KICKING PLATE : Removal and Installation".
2. Lift up rear end of dash side finisher to release pawls. : Pawl
3. Pull back dash side finisher to release dash side finisher from stud and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls for deformati on and damage during installation.
• When installing, check that fi nisher is aligned with stud bolt located on floor panel.
• When installing dash side fi nisher, check that pawls are secure ly placed into body panel holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and InstallationINFOID:0000000012431868
FRONT BODY SIDE WELT
Removal
1. Remove the dash side finisher. Refer to INT-24, "DASH SIDE FINISHER : Removal and Installation".
2. Remove front body side welt.
Installation
Installation is in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove rear kicking plate. Refer to INT-22, "KICKING PLATE : Removal and Installation".
2. Remove rear body side welt.
AWJIA1092ZZ
AWJIA1093ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2177 of 3641
INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
When releasing molded in clip, follow the steps as shown to prevent finisher or clip damage.
7. Release center pillar upper finisher lower clip using a suitable tool (A) and remove.
: Clip
CAUTION:
Do not reuse center pillar upper finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse center pillar upper finisher. Replace with new part for installation.
• When installing center pillar upper finisher, check that clips are securely placed in body panel holes.
PIIB2600J
AWJIA1094ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2179 of 3641
INT-28
< REMOVAL AND INSTALLATION >
FLOOR TRIM
6. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
WARNING:
Before servicing the SRS, turn th e ignition switch off, disconnect both battery terminals then wait
at least three minutes.
7. Disconnect the harness connector (A ) from the seat belt retrac-
tor (1).
WARNING:
• Do not drop the seat belt retractor. Always handle it with care.
• Always point pretensioner cylinder away from body when handling.
CAUTION:
• For removing/installing the shoulder belt pre-tensioner harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
8. Remove seat belt lower anchor bolt. CAUTION:
Before removing the seat belt lower anchor bolt , note the positions of washers and spacers for
correct installation.
9. Remove diagnosis sensor unit. Refer to SR-30, "
Removal and Installation".
10. Remove shift selector. Refer to TM-20, "
Exploded View" (5MT) or TM-231, "Removal and Installation"
(CVT).
11. Remove A/C unit assembly bolt (C) and bracket (1) from vehicle.
12. Remove instrument panel lower bracket bolt (B) and screw (A) and reposition bracket as necessary to remove floor trim.
ALHIA0316ZZ
PHIA0953J
ALJIA0712ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com