lock NISSAN NOTE 2016 Service Repair Manual

POWER WINDOW MOTORPWC-37
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
L
M A
B
PWC
N
O P
Is the inspection result normal?
YES >> Replace rear power window switch LH. Refer to PWC-57, "Removal and Installation".
NO >> Repair or replace harness.
REAR RH
REAR RH : Component Function CheckINFOID:0000000012431825
1. CHECK FUNCTION
Check rear power window motor RH operation with main power window and door lock/unlock switch or rear
power window switch RH.
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to PWC-37, "
REAR RH : Diagnosis Procedure".
REAR RH : Diagnosis ProcedureINFOID:0000000012431826
Regarding Wiring Diagram information, refer to PWC-16, "Wiring Diagram".
1.CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window motor RH connector.
3. Turn ignition switch ON.
4. Check voltage between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES >> Replace rear power window motor RH.
NO >> GO TO 2.
2.CHECK REAR POWER WINDOW MOTOR RH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear power window switch RH connector.
3. Check continuity between rear power window swit ch RH harness connector and rear power window motor
RH harness connector.
4. Check continuity between rear power window switch RH harness connector and ground.
Rear power window switch LH GroundContinuity
Connector Terminal
D203 6
No
5
(+)
(-)Condition Voltage (V)
(Approx.)
Rear power window motor RH
Connector Terminal
D304 1
GroundRear power window
switch RH NEUTRAL
0
UP Battery voltage
2 NEUTRAL
0
DOWN Battery voltage
Rear power window switch RH Rear power window motor RH
Continuity
Connector TerminalConnector Terminal
D303 6
D304 2
Ye s
51
Revision: August 2015 2016 Versa Note

cardiagn.com

DOOR SWITCHPWC-39
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
L
M A
B
PWC
N
O P
DOOR SWITCH
WITH INTELLIGENT KEY SYSTEM
WITH INTELLIGENT KEY SYST EM : Component Function CheckINFOID:0000000012431827
1.CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR SW-DR” and “DOOR SW-AS” in “Data Monitor”.
3. Check that the function operates normall y according to the following conditions:
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Refer to PWC-39, "
WITH INTELLIGENT KEY SYSTEM : Diagnosis Procedure".
WITH INTELLIGENT KEY SYST EM : Diagnosis ProcedureINFOID:0000000012431828
Regarding Wiring Diagram information, refer to PWC-16, "Wiring Diagram".
1.CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check signal between malfunctioning door switch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between door switch harness connector and BCM harness connector.
Monitor item Condition Status
DOOR SW-DR Front door LH Open
ON
Closed OFF
DOOR SW-AS Front door RHOpen
ON
Closed OFF
(+)
(–)Signal
(Reference value)
Door switch
Connector Terminal
Front door switch
LH B8
3
Ground
7.0 - 8.0 V
Front door switch
RH
B16
3
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

POWER WINDOW CONTROL SYSTEM SYMPTOMS
PWC-43
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
SYMPTOM DIAGNOSIS
POWER WINDOW CONTROL SYSTEM SYMPTOMS
Symptom TableINFOID:0000000012431834
Symptom Reference page
None of the power windows can be operated using any switch. Refer to PWC-44, "
Diagnosis Proce-
dure".
Driver side power window does not operate. Refer to PWC-45, "
Diagnosis Proce-
dure".
Front passenger side power window does not operate (When both main power window and
door lock/unlock switch and power window and door lock/unlock switch RH are
operated). Refer to PWC-46, "
WHEN BOTH POW-
ER WINDOW MAIN SWITCH AND
FRONT POWER WINDOW SWITCH
ARE OPERATED :
Diagnosis Proce-
dure".
Front passenger side power window does not operate (when power window and door lock/
unlock switch RH is operated). Refer to PWC-46, "
WHEN FRONT
POWER WINDOW SWITCH (PASSEN-
GER SIDE) IS OPERATED : Diagnosis
Procedure".
Front passenger side power window does not operate (when power window main switch
is operated). Refer to PWC-47, "
WHEN POWER WIN-
DOW MAIN SWITCH IS OPERATED :
Diagnosis Procedure".
Rear (LH) side power window does not operate (when both main power window and door
lock/unlock switch and rear power window switch LH are operated). Refer to PWC-48, "
WHEN BOTH POW-
ER WINDOW MAIN SWITCH AND
REAR POWER WINDOW SWITCH LH
ARE OPERATED :
Diagnosis Proce-
dure".
Rear (LH) side power window does not operate (when rear power window switch LH is op-
erated). Refer to PWC-48, "
WHEN REAR POW-
ER WINDOW SWITCH LH IS OPERAT-
ED : Diagnosis Procedure".
Rear (LH) side power window does not operate (when main power window and door lock/
unlock switch is operated). Refer to
PWC-49, "
WHEN POWER WIN-
DOW MAIN SWITCH IS OPERATED :
Diagnosis Procedure".
Rear (RH) side power window does not operate (when both main power window and door
lock/unlock switch and rear power window switch RH are operated). Refer to PWC-50, "
WHEN BOTH POW-
ER WINDOW MAIN SWITCH AND
REAR POWER WINDOW SWITCH RH
ARE OPERATED :
Diagnosis Proce-
dure".
Rear (RH) side power window does not operate (when rear power window switch RH is
operated). Refer to PWC-50, "
WHEN REAR POW-
ER WINDOW SWITCH RH IS OPERAT-
ED : Diagnosis Procedure".
Rear (RH) side power window does not operate (when main power window and door lock/
unlock switch is operated) Refer to PWC-51, "
WHEN POWER WIN-
DOW MAIN SWITCH IS OPERATED :
Diagnosis Procedure".
Power window lock switch does not function. Refer to PWC-54, "
Diagnosis Proce-
dure".
Revision: August 2015
2016 Versa Note

cardiagn.com

PWC-44
< SYMPTOM DIAGNOSIS >
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH
Diagnosis ProcedureINFOID:0000000012431835
1.CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit. Refer to PWC-25, "
BCM (BODY CONTROL SYSTEM) (WITH
INTELLIGENT KEY SYSTEM) : Diagnosis Procedure" (with Intelligent Key system) or PWC-25, "BCM (BODY
CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY S YSTEM) : Diagnosis Procedure" (without Intelligent
Key system).
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK MAIN POWER WINDOW AND DOOR LOCK /UNLOCK SWITCH POWER SUPPLY AND GROUND
CIRCUIT
Check main power window and door lock/unlock switch power supply and ground circuit.
Refer to PWC-26, "
POWER WINDOW MAIN SWITCH : Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Revision: August 2015 2016 Versa Note

cardiagn.com

PWC-46
< SYMPTOM DIAGNOSIS >
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED
WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED : Diagnosis Procedure
INFOID:0000000012431837
1.CHECK POWER WINDOW AND DO OR LOCK/UNLOCK SWITCH RH
Check power window and door lock/unlock switch RH.
Refer to PWC-30, "
Component Function Check".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK FRONT POWER WINDOW MOTOR RH
Check front power window motor RH.
Refer to PWC-35, "
PASSENGER SIDE : Component Function Check".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED
WHEN FRONT POWER WINDOW SWITCH (P ASSENGER SIDE) IS OPERATED :
Diagnosis Procedure
INFOID:0000000012431838
1.CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH POWER SUPPLY AND GROUND
CIRCUIT
Check power window and door lock/unlock switch RH power supply and ground circuit.
Refer to PWC-27, "
FRONT POWER WINDOW SWITCH (PASSE NGER SIDE) : Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK POWER WINDOW AND DO OR LOCK/UNLOCK SWITCH RH
Check power window and door lock/unlock switch RH.
Refer to PWC-30, "
Component Function Check".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
PWC-47
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000012431839
1.CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
Check power window and door lock/unlock switch RH.
Refer to PWC-30, "
Component Function Check".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Revision: August 2015 2016 Versa Note

cardiagn.com

PWC-52
< SYMPTOM DIAGNOSIS >
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NORMAL-LY (DRIVER SIDE)
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NOR-
MALLY (DRIVER SIDE)
Diagnosis ProcedureINFOID:0000000012431846
1.REPLACE MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Replace main power window and door lock/unlock switch.
>> Refer to PWC-55, "
Removal and Installation".
Revision: August 2015 2016 Versa Note

cardiagn.com

PWC-54
< SYMPTOM DIAGNOSIS >
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis ProcedureINFOID:0000000012431848
1.REPLACE MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Replace main power window and door lock/unlock switch.
>> Refer to PWC-55, "
Removal and Installation".
Revision: August 2015 2016 Versa Note

cardiagn.com

MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCHPWC-55
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
PWC
N
O P
REMOVAL AND INSTALLATION
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Removal and InstallationINFOID:0000000012829245
REMOVAL
1. Remove main power window and door lock/unlock switch finisher door handle pull escutcheon.
2. Remove screw (A) from main power window and door lock/
unlock switch finisher.
3. Remove main power window and door lock/unlock switch fin- isher (1) using a suitable tool (B).
: Pawl
4. Disconnect the harness connectors from the ma in power window and door lock/unlock switch.
5. Release pawls and remove main power window and door lock/ unlock switch (1) from main power window and door lock/unlock
switch finisher assembly (2) using a suitable tool.
: Pawl
CAUTION:
Do not bend back the pawls on th e switch finisher too far or
damage may occur.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
When the main power window and door lock/unlock switch is removed or replaced, it is necessary to perform
the initialization procedure. Refer to PWC-23, "
Work Flow".
AWKIA2536ZZ
AWKIA2506ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

PWC-56
< REMOVAL AND INSTALLATION >
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
Removal and InstallationINFOID:0000000012829246
REMOVAL
1. Remove power window and door lock/unlock switch (RH) finisher door handle pull escutcheon.
2. Remove screw (B) from power window and door lock/unlock
switch (RH) finisher.
3. Remove power window and door lock/unlock switch (RH) fin- isher (1) using a suitable tool (A).
: Pawl
4. Disconnect the harness connector from the pow er window and door lock/unlock switch (RH).
5. Release pawls and remove power window and door lock/unlock switch (1) from power window and door lock/unlock switch (RH)
finisher (2) using a suitable tool.
: Pawl
CAUTION:
Do not bend back the pawls on the switch finisher too far or
damage may occur.
INSTALLATION
Installation is in the reverse order of removal.
AWKIA2505ZZ
AWKIA2507ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com