lock NISSAN NOTE 2016 Service Repair Manual

MAIN POWER SUPPLY AND GROUND CIRCUITTM-215
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
MAIN POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000012431161
1.CHECK TCM POWER CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check voltage between TCM harness connector terminals and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK TCM POWER CIRCUIT (PART 2)
Check voltage between TCM harness connector terminals and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK TCM GROUND CIRCUIT
Check continuity between TCM har ness connector terminals and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Repair or replace malfunctioning parts.
4.DETECT MALFUNCTION ITEMS (PART 1)
Check the following items:
• Open circuit or short circuit in harness between bat tery positive terminal and TCM connectors terminals 45,
and 46.
• 10A fuse (No.33, fuse and fusible link block). Refer to PG-59, "
Terminal Arrangement".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Repair or replace malfunctioning parts.
+
−Vo l ta g e
TCM
Connector Terminal
F44 45
Ground 10 – 16 V
46
+
−Condition Voltage
TCM
Connector Terminal
F44 47
GroundIgnition switch ON 10 – 16 V
Ignition switch OFF Approx. 0 V
48 Ignition switch ON 10 – 16 V
Ignition switch OFF Approx. 0 V
TCM
— Continuity
Connector Terminal
F44 41
Ground Existed
42
Revision: August 2015 2016 Versa Note

cardiagn.com

SHIFT LOCK SYSTEMTM-221
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SHIFT LOCK SYSTEM
Component Function CheckINFOID:0000000012431169
1.CHECK SHIFT LOCK OPERATIO N (BRAKE PEDAL RELEASED)
1. Ignition switch ON.
2. Attempt to shift selector lever to any position other than “P” position with brake pedal released.
Can the selector lever be shifted?
YES >> Go to TM-221, "Diagnosis Procedure".
NO >> GO TO 2.
2.CHECK SHIFT LOCK OPERATIO N (BRAKE PEDAL APPLIED)
Attempt to shift the selector lever to any pos ition other than “P” position with brake pedal applied.
Can the selector lever be shifted?
YES >> Inspection End.
NO >> Go to TM-221, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431170
1.CHECK STOP LAMP SWITCH
1. Ignition switch ON.
2. Check voltage between stop lamp switch connector E13 terminal 4 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK GROUND CIRCUIT
1. Ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Check continuity between CVT shift selector connector M38 terminal 6 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace ground circuit.
3.CHECK STOP LAMP SWITCH POWER CIRCUIT
Check voltage between stop lamp switch connector E13 terminal 3 and ground.
Is the inspection result normal?
YES >> Replace stop lamp switch.
NO >> Repair or replace power circuit.
Stop lamp switch Ground Brake pedal Voltage
Connector Terminal
E13 4Ground Applied
Battery voltage
Released 0V
CVT shift selector
GroundContinuity
Connector Terminal
M38 6Ground Yes
Stop lamp switch
GroundVoltage
Connector Terminal
E13 3GroundBattery voltage
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-222
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
SHIFT LOCK SYSTEM
4.CHECK CVT SHIFT SELECTOR POWER CIRCUIT
Check voltage between CVT shift selector connector M38 terminal 5 and ground.
Is the inspection result normal?
YES >> Replace CVT shift selector. Refer to TM-231, "Removal and Installation".
NO >> Repair or replace power circuit.
CVT shift selector GroundBrake pedal Voltage
Connector Terminal
M38 5Ground AppliedBattery voltage
Revision: August 2015 2016 Versa Note

cardiagn.com

CVT CONTROL SYSTEMTM-223
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
CVT CONTROL SYSTEM
Symptom TableINFOID:0000000012431171
The diagnosis item number indicates the order of check. Start checking in the order from 1.
Symptom diagnosis chart 1-1
SymptomCheck under on board condition (repair
and part replacement) Replace the transaxle assembly.
Engine system
Incorrect adjustment of CVT fluid level
Line pressure is out of the standard value.
Control cable
Electric system
TCM
Overdrive control switch
Primary speed sensor (P0715)
Secondary speed sensor (P2765)
Output speed sensor (P0720)
Transmission position switch (P0705, P0706)
Secondary pressure sensor (P0846, P0847, P0848)
Primary pressure soleno
id valve (P17BA, P17BB)
Line pressure solenoid valve (P0746, P0962, P0963)
Lock-up solenoid valve
(P0740, P0743, P0744)
High clutch &reverse brake solenoid valve
(P1739, P173C, P17B7, P17B8)
Low brake solenoid valve
(P173A, P173B, P17B4, P17B5)
CVT fluid temperature sensor (P0711, P0712, P0713)
EC-120
TM-229TM-131TM-232TM-99TM-217TM-110
Driving is
not possi-
ble. The engine speed increases in
“D”, “L”, or “R” position, but the
vehicle cannot start.
11111 11 12 1 1 1 2
Engine stall occurs in “D”, “L”,
or “R” position and the vehicle
does not start. 11 11 1111 1 1 2
Acceleration at start is not suf-
ficient in “D”, “L”, or “R” posi-
tion. 1 2 1 1112211 2 1 1 1
The engine speed increases
suddenly in “D”, “L”, or “R” po-
sition during driving. 11
211 1 1
Engine brake is suddenly ap-
plied in “D” or “R” position dur-
ing driving. 11
11 11
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-224
< SYMPTOM DIAGNOSIS >[CVT: RE0F11A]
CVT CONTROL SYSTEM
Shifting is
not possi-
ble. The engine races when the
auxiliary gearbox is shifted
from 1GR ⇔
2GR. 21
1 11
Engine braking is not effective
in “L” position. 111 11 1 21 1 1
Shifting does not occur with
OD OFF. 111111 11
Engine stall occurs immediate-
ly before stop at deceleration in
“D” or “L” position. 11
During driving in “D” position,
slippage occurs in lockup or
lockup is not possible. 1 1111211 1
1
Symptom
Check under on board condition (repair
and part replacement) Replace the transaxle assembly.
Engine system
Incorrect adjustment of CVT fluid level
Line pressure is out of the standard value.
Control cable
Electric system
TCM
Overdrive control switch
Primary speed sensor (P0715)
Secondary speed sensor (P2765)
Output speed sensor (P0720)
Transmission position switch (P0705, P0706)
Secondary pressure sensor (P0846, P0847, P0848)
Primary pressure solenoid valve (P17BA, P17BB)
Line pressure solenoid valve (P0746, P0962, P0963)
Lock-up solenoid valve
(P0740, P0743, P0744)
High clutch &reverse brake solenoid valve
(P1739, P173C, P17B7, P17B8)
Low brake solenoid valve
(P173A, P173B, P17B4, P17B5)
CVT fluid temperature sensor (P0711, P0712, P0713)
EC-120
TM-229TM-131TM-232TM-99TM-217TM-110
Revision: August 2015
2016 Versa Note

cardiagn.com

CVT CONTROL SYSTEMTM-225
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom diagnosis chart 1-2
Symptom Replace the transaxle assembly.
Oil pres-
sure con- trol Power transmission
Valve body, control valve
Oil pump
Torque converter
Pulley, steel belt
Low brake
High clutch
Reverse brake
Bearings
Counter gear
Planetary gear
Reduction gear
Final gear, differential gear
Parking mechanism
TM-259
Driving is
not possi- ble. The engine speed increases in
“D”, “L”, or “R” position, but the
vehicle cannot start.
11 11
(In “D” or “L”) 1
(In “R”) 1111
Engine stall occurs in “D”, “L”,
or “R” position and the vehicle
does not start. 1
111111
Acceleration at start is not suf-
ficient in “D”, “L”, or “R” posi-
tion. 111
(In “D” or “L”) 1
(In “R”)
The engine speed increases
suddenly in “D”, “L”, or “R” po-
sition during driving. 11 11
(In “D” or “L”) 1
(In “D” or “L”) 1
(In “R”)
Engine brake is suddenly ap-
plied in “D” or “R” position dur-
ing driving. 1
1
(In “D” or
“L”) 1
(In “D” or
“L”) 1
(In “R”)
Shifting is
not possi- ble. The engine races when the
auxiliary gearbox is shifted
from 1GR ⇔
2GR. 11 2 1 1
Engine braking is not effective
in “L” position. 1212 1 1
Shifting does not occur with
OD OFF.
Engine stall occurs immedi-
ately before stop at decelera-
tion in “D” or “L” position. 11
During driving in “D” position,
slippage occurs in lockup or
lockup is not possible. 11
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-226
< SYMPTOM DIAGNOSIS >[CVT: RE0F11A]
CVT CONTROL SYSTEM
Symptom diagnosis chart 2-1
SymptomCheck under on board condition (repair
and part replacement) Replace the transaxle assembly.
Engine system
Incorrect adjustment of CVT fluid level
Line pressure is out of the standard value.
Control cable
Electric system
TCM
Overdrive control switch
Primary speed sensor (P0715)
Secondary speed sensor (P2765)
Output speed sensor (P0720)
Transmission position switch (P0705, P0706)
Secondary pressure sensor (P0846, P0847, P0848)
Primary pressure soleno
id valve (P17BA, P17BB)
Line pressure solenoid valve (P0746, P0962, P0963)
Lock-up solenoid valve
(P0740, P0743, P0744)
High clutch &reverse brake solenoid valve
(P1739, P173C, P17B7, P17B8)
Low brake solenoid valve
(P173A, P173B, P17B4, P17B5)
CVT fluid temperature sensor (P0711, P0712, P0713)
EC-120
TM-229TM-131TM-232TM-99TM-217TM-110
Shock vi-
bration
Noise Shock at start is large in “D”,
“L”, or “R” position.
12
11
Shock is large when the aux-
iliary gearbox is shifted from
1GR → 2GR. 212
22 11
Shock in lockup is large dur-
ing driving in “D ” or “L” posi-
tion. 11
Shock is large when the lever
is shifted from “N” → “D” and
“N” → “R” positions. 1 12111 11111
Shock is large when the lever
is shifted from “D” → “L” posi-
tion.
Vibration occurs in “D”, “L”, or
“R” position during driving. 1111 12 111
Noise occurs during driving. 1
Noise occurs in idling. 1 1
Other Starter operates in “D”, “L”, or
“R” position.
11
1
Starter does not operate in
“P” or “N” position. 11
1
Engine stall occurs in “D”, “L”,
or “R” position during stop. 111 1
Engine stall occurs in “P” or
“N” position during stop. 111 1
Parking lock does not oper-
ate in “P” position. 11
Parking lock cannot be can-
celled when the selector le-
ver is shifted from “P” position
to other position. 11
Revision: August 2015
2016 Versa Note

cardiagn.com

CVT CONTROL SYSTEMTM-227
< SYMPTOM DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom diagnosis chart 2-2
Symptom Replace the transaxle assembly.
Oil pres-
sure con- trol Power transmission
Valve body, control valve
Oil pump
Torque converter
Pulley, steel belt
Low brake
High clutch
Reverse brake
Bearings
Counter gear
Planetary gear
Reduction gear
Final gear, differential gear
Parking mechanism
TM-259
Shock vi-
bration
Noise Shock at start is large in “D”,
“L”, or “R” position.
111
(In “D” or “L”) 1
(In “R”) 2222
Shock is large when the auxil-
iary gearbox is shifted from
1GR → 2GR. 11
1
Shock in lockup is large dur-
ing driving in “D” or “L” posi-
tion. 11
Shock is large when the lever
is shifted from “N” → “D” and
“N” → “R” positions. 11
(“N” →
“D”) 1
(“N” →
“D”)
Shock is large when the lever
is shifted from “D” → “L” posi-
tion. 11
1
Vibration occurs in “D”, “L”, or
“R” position during driving. 11111
(In “D” or “L”) 1
(In “D” or “L”) 1
(In “R”) 11111
Noise occurs during driving. 1 1 1 11111
Noise occurs in idling. 1 1 1 1 1 1
Other Starter operates in “D”, “L”, or
“R” position.
Starter does not operate in “P”
or “N” position.
Engine stall occurs
in “D”, “L”,
or “R” position during stop. 11
Engine stall occurs in “P” or
“N” position during stop.
Parking lock does not operate
in “P” position. 1
Parking lock cannot be can-
celled when the selector lever
is shifted from “P” position to
other position. 1
Revision: August 2015
2016 Versa Note

cardiagn.com

CVT SHIFT SELECTORTM-231
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded ViewINFOID:0000000012431175
Removal and InstallationINFOID:0000000012431176
CAUTION:
Always apply the parking brake before pe rforming removal and installation.
REMOVAL
1. Move the shift selector to the “N” position.
2. Remove the shift selector handle. Refer to TM-232, "
Disassembly and Assembly".
3. Remove the center console. Refer to IP-18, "
Removal and Installation".
4. Disconnect the harness connectors from shift selector.
5. Move the shift selector to the “P” position.
6. Remove the key interlock cable from the shift selector assembly. Refer to TM-237, "
Exploded View".
7. Remove the control cable from the shift selector assembly. Refer to TM-234, "
Exploded View".
8. Remove the shift selector assembly.
INSTALLATION
Installation is in the reverse order of removal.
1. Shift selector handle 2. Lock pin3. Shift selector handle cover
4. Position indication panel 5. Shift selector assembly
ALDIA0263GB
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-232
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
CVT SHIFT SELECTOR
• When connecting the control cable (1) to the shift selector assem-
bly (2), face the grooved surface of the rib (A) up and insert the
control cable until it stops.
Disassembly and AssemblyINFOID:0000000012431177
DISASSEMBLY
1. Slide the shift selector handle cover (1) down. CAUTION:
Do not damage the shift selector handle cover.
2. Pull out the lock pin (2).
3. Pull the shift selector handle (3) and shift selector handle cover upward to remove.
4. Remove the position lamp.
5. Disengage the hooks (A) (4 locations), and lift up the position indication panel (1) to separate it from the shift selector assem-
bly (2).
CAUTION:
Do not damage the shift selector assembly.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Follow the procedure below to install the shift selector handle.
1. Install the lock pin (2) onto the shift selector handle (3).
2. Install the shift selector handle cover (1) onto the shift selectorhandle.
3. Press the shift selector handle onto the shift selector until it clicks.
CAUTION:
• When pressing the shift selector handle onto the shift
selector, do not press the shift selector handle button.
• Do not strike the shift selector handle to install it.
InspectionINFOID:0000000012431178
INSPECTION AFTER INSTALLATION
JSDIA1624ZZ
JSDIA1796ZZ
ALDIA0264ZZ
JSDIA1796ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com