brake NISSAN NOTE 2016 Service Manual PDF

BRC-72
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1110, C1153 ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
C1110, C1153 ABS ACTUATOR AND EL
ECTRIC UNIT (CONTROL UNIT)
DTC DescriptionINFOID:0000000012430860
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1110” or “C1153” detected?
YES-1 >> “C1110” or “C1153” is displayed as “CRNT”: Proceed to BRC-73, "Diagnosis Procedure".
YES-2 >> “C1110” or “C1153” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of
“ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C 111 0 CONTROLLER FAILURE
(Controller failure) When there is an internal malfunction in the ABS ac
tuator and electric unit (control unit).
C1153 EMERGENCY BRAKE
(Emergency brake) When ABS actuator and electric
unit (control unit) is malfunctioning (Pressure increase
is too much or too little).
DTC PAST DTC CRNT DTC
C 111 0 • The vehicle travels near high-voltage electrical power
lines.
• Motor built-in the ABS actuator and electric unit (control
unit) operates temporarily without a break.
• Harness or connector
• ABS actuator and electric unit (control unit) power supply system
•Fuse
• Fusible link
• Battery • Incomplete neutral position adjustment of steering angle-
sensor
• ABS actuator and electric unit (control unit)
• Harness or connector
• ABS actuator and electric unit (control unit) power supply
system
•Fuse
• Fusible link
•Battery
C1153 • The vehicle travels near high-voltage electrical power
lines.
• ABS operates for a long time (e.g. travel under a tire hy- droplaning condition). ABS actuator and electric unit (control unit)
Revision: August 2015
2016 Versa Note

cardiagn.com

BRC-84
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
C1116 STOP LAMP SWITCH
DTC DescriptionINFOID:0000000012430866
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF, and wait 10 seconds or more.
2. Start the engine.
NOTE:
Stop the vehicle.
3. Wait 1 minute or more. NOTE:
Never depress brake pedal.
4. Depress brake pedal by 100 mm (3.94 in) or more, and ma intain at that position for a minimum of 1 minute
or more.
5. Release brake pedal, and wait 1 minute or more.
6. Repeat step 4 to 5 ten or more times.
7. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
9. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1116” detected?
YES-1 >> “C1116” is displayed as “CRNT”: Proceed to BRC-85, "Diagnosis Procedure".
YES-2 >> “C1116” is displayed as “PAST”: Inspection End (Erase “Self Diagnos tic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C 111 6 STOP LAMP SW
(Stop lamp switch) • When stop lamp switch signal is not input when brake pedal operates.
• When stop lamp switch signal is input when brake pedal is not operated.
PAST DTC
CRNT DTC
• Harness or connector
• Stop lamp switch signal circuit • Harness or connector
• Stop lamp switch
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note

cardiagn.com

C1116 STOP LAMP SWITCHBRC-85
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Diagnosis ProcedureINFOID:0000000012430867
NOTE:
DTC “C1116” may be detected when the brake pedal and the accelerator pedal are simultaneously depressed
for 1 minute or more while driving the vehicle. This is not a malfunction.
1.INTERVIEW FROM THE CUSTOMER
Check if the brake pedal and the accelerator pedal ar e simultaneously depressed for 1 minute or more while
driving the vehicle.
Is there such a history?
YES >> GO TO 2.
NO >> GO TO 3.
2.PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Stop the vehicle.
4. Depress the brake pedal several times.
5. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
6. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
7. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C 111 6” detected?
YES >> GO TO 3.
NO >> Inspection End.
3.STOP LAMP FOR ILLUMINATION
Depress brake pedal and check that stop lamps turn ON.
Do the stop lamps turn ON?
YES >> GO TO 5.
NO >> Check the stop lamp system. Refer to EXL-63, "
Wiring Diagram". GO TO 4.
4.CHECK DATA MONITOR (1)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Stop the vehicle.
4. Select “DATA MONITOR” of “ABS”, check “STOP LA MP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-36, "
Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 5.
5.CHECK CONNECTOR AND TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check the ABS actuator and electric unit (contro l unit) harness connector for disconnection or looseness.
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-86
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
4. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector.
5. Disconnect stop lamp switch harness connector.
6. Check the stop lamp switch harness connector for disconnection or looseness.
7. Check the stop lamp switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair / replace harness, connector, or terminal, and GO TO 6.
6.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (contro l unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair / replace harness, connector, fuse, or fusible link.
7.CHECK DATA MONITOR (2)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine. NOTE:
Stop the vehicle.
4. Select “DATA MONITOR” of “ABS”, check “STOP LA MP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-36, "
Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 8.
8.CHECK STOP LAMP SWITCH CIRCUIT (1)
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check the voltage between ABS actuator and elec tric unit (control unit) harness connector and ground.
4. Turn the ignition switch ON.
5. Check the voltage between ABS actuator and elec tric unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair / replace harness or connector, and GO TO 9.
9.CHECK STOP LAMP SWITCH CIRCUIT (2)
1. Turn the ignition switch OFF.
ABS actuator and electric unit (control unit) — Condition Vo l ta g e
(Approx.)
Connector Terminal
E33 12Ground Brake pedal depressed
10 − 16 V
Brake pedal not depressed 0 V
ABS actuator and electric unit (control unit)
— Condition Vol tag e
(Approx.)
Connector Terminal
E33 12Ground Brake pedal depressed
10 − 16 V
Brake pedal not depressed 0 V
Revision: August 2015 2016 Versa Note

cardiagn.com

C1116 STOP LAMP SWITCHBRC-87
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2. Disconnect stop lamp switch harness connector.
3. Check the continuity between ABS actuator and electric unit (control unit) harness connector and stop lamp switch harness connector.
4. Check the continuity between ABS actuator and el ectric unit (control unit) harness connector and the
ground.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair / replace harness or connector, and GO TO 10.
10.CHECK DATA MONITOR (3)
With CONSULT
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect stop lamp switch harness connector.
3. Erase “Self Diagnostic Result” of “ABS”
4. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine.
NOTE:
Stop the vehicle.
6. Select “DATA MONITOR” of “ABS”, check “STOP LA MP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-36, "
Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "
Removal and Instal-
lation".
Component InspectionINFOID:0000000012430868
1.CHECK STOP LAMP SWITCH
1. Turn the ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check the continuity when stop lamp switch is operated.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the stop lamp switch. Refer to BR-20, "
Removal and Installation".
ABS actuator and electric unit (control unit) Stop lamp switch
Continuity
Connector TerminalConnector Terminal
E33 12E13 (WITH CVT)
2Yes
E57 (WITH M/T)
ABS actuator and electric unit (control unit)
—Con tin uit y
Connector Terminal
E33 12Ground No
Stop lamp switch
Condition Continuity
Te r m i n a l
1 – 2 When stop lamp switch is released
(When brake pedal is depressed) Ye s
When stop lamp switch is pressed (When brake pedal is released) No
Revision: August 2015
2016 Versa Note

cardiagn.com

BRC-96
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1142 PRESS SENSOR
C1142 PRESS SENSOR
DTC DescriptionINFOID:0000000012430877
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1142” detected?
YES-1 >> “C1142” is displayed as “CRNT”: Proceed to BRC-96, "Diagnosis Procedure".
YES-2 >> “C1142” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430878
1.STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to BRC-85, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace stop lamp switch system.
2.CHECK BRAKE FLUID LEAKAGE
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1142 PRESS SEN CIRCUIT
(Pressure sensor circuit) When a malfunction is detected in pressure sensor.
PAST DTC
CRNT DTC
• Harness or connector
• Air inclusion in the brake piping
• Stop lamp switch system
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Stop lamp switch system
• ABS actuator and electric unit (control unit)
• Brake system
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• Air inclusion in the brake piping
Revision: August 2015 2016 Versa Note

cardiagn.com

C1142 PRESS SENSORBRC-97
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Check the brake fluid leakage. Refer to BR-12, "Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace brake fluid leakage part.
3.CHECK BRAKE PIPING
Check the brake piping. Refer to BR-12, "
Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace brake piping. • Front: Refer to BR-23, "
FRONT : Removal and Installation".
• Rear: Refer to BR-26, "
REAR : Removal and Installation".
4.CHECK BRAKE PEDAL
Check the brake pedal.
• Brake pedal height: Refer to BR-9, "
Inspection and Adjustment".
• Brake pedal assembly: Refer to BR-20, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Adjust the brake pedal height or replace brake pedal assembly. • Adjust the brake pedal: Refer to BR-9, "
Inspection and Adjustment".
• Replace the brake pedal: Refer to BR-20, "
Removal and Installation".
5.CHECK BRAKE MASTER CYLINDER
Check the brake master cylinder. Refer to BR-14, "
Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace brake master cylinder. Refer to BR-28, "
Removal and Installation".
6.CHECK BRAKE BOOSTER
Check the brake booster. Refer to BR-15, "
Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace brake booster. Refer to BR-31, "
Removal and installation".
7.CHECK VACUUM PIPING
Check the vacuum piping. Refer to BR-33, "
Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace vacuum piping. Refer to BR-33, "
Removal and Installation".
8.CHECK FRONT DISC BRAKE
Check the front disc brake caliper. Refer to BR-36, "
BRAKE CALIPER ASSEMBLY : Exploded View".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace front disc brake caliper. Refer to BR-37, "
BRAKE CALIPER ASSEMBLY :
Removal and Installation".
9.CHECK REAR BRAKE
Check the rear brake. Refer to BR-41, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair or replace rear brake. Refer to BR-41, "
Removal and Installation".
10.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) POWER SUPPLY AND GROUND
CIRCUIT
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-108
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1155 BRAKE FLUID LEVEL SWITCH
C1155 BRAKE FLUID LEVEL SWITCH
DTC DescriptionINFOID:0000000012430887
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES-1 >> “C1155” is displayed as “CRNT”: Proceed to BRC-108, "Diagnosis Procedure".
YES-2 >> “C1155” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430888
1.CHECK BRAKE FLUID LEVEL
1. Turn the ignition switch OFF.
2. Check the brake fluid level. Refer to BR-12, "
Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Refill brake fluid. Refer to BR-12, "
Refilling". GO TO 2.
2.PERFORM SELF-DIAGNOSIS (1)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1155 BR FLUID LEVEL LOW
(Brake fluid level low) • When brake fluid level low signal is detected.
• When an open circuit is detected in brake fluid level switch circuit.
PAST DTC
CRNT DTC
• Harness or connector
• Brake fluid level is low • Harness or connector
• ABS actuator and electric unit (control unit)
• Brake fluid level switch
• Combination meter
• Brake fluid level is low
Revision: August 2015
2016 Versa Note

cardiagn.com

C1155 BRAKE FLUID LEVEL SWITCHBRC-109
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
4. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 3.
NO >> Inspection End.
3.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the combination meter harness connector for disconnection or looseness.
3. Check the brake fluid level switch harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair / replace harness or connector, and GO TO 4.
4.PERFORM SELF-DIAGNOSIS (2)
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 5.
NO >> Inspection End.
5.CHECK BRAKE FLUID LEVEL SWITCH
Check the brake fluid level switch. Refer to BR-28, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace the reservoir tank. Refer to BR-28, "
Exploded View". GO TO 6.
6.PERFORM SELF-DIAGNOSIS (3)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
4. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 7.
NO >> Inspection End.
7.CHECK CONNECTOR AND TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect brake fluid level switch harness connector.
3. Check the brake fluid level switch harness connector for disconnection or looseness.
4. Check the brake fluid level switch pin terminal s for damage or loose connection with harness connector.
5. Disconnect combination meter harness connector.
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-110
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1155 BRAKE FLUID LEVEL SWITCH
6. Check the combination meter harness connector for disconnection or looseness.
7. Check the combination meter pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair / replace harness, connector, or terminal, and GO TO 8.
8.PERFORM SELF-DIAGNOSIS (4)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
4. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1155” detected?
YES >> GO TO 9.
NO >> Inspection End.
9.CHECK BRAKE FLUID LEVEL SWITCH CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect brake fluid level switch harness connector.
3. Disconnect combination meter harness connector.
4. Check the continuity between brake fluid level switch harness connector and combination meter harness
connector.
5. Check the continuity between brake fluid level switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair / replace harness or connector, and GO TO 10.
10.CHECK BRAKE FLUID LEVEL SWITCH GROUND CIRCUIT
Check the continuity between brake fluid level switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair / replace harness or connector, and GO TO 11.
11 .CHECK COMBINATION METER
Check the combination meter. Refer to MWI-18, "
CONSULT Function (METER/M&A)" (TYPE A) or MWI-71,
"CONSULT Function (METER/M&A)" (TYPE B).
Is the inspection result normal?
Brake fluid level switch Combination meter
Continuity
Connector TerminalConnector Terminal
E40 1M24 (TYPE B)
11Ye s
M82 (TYPE A)
Brake fluid level switch —Continuity
Connector Terminal
E40 1Ground No
Brake fluid level switch
—Continuity
Connector Terminal
E40 2Ground Yes
Revision: August 2015 2016 Versa Note

cardiagn.com