brake NISSAN NOTE 2016 Service Owners Manual

TIMING CHAINEM-59
< REMOVAL AND INSTALLATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
• Secure crankshaft pulley with a suitable tool and tighten crankshaft pulley bolt.
a. Apply new engine oil to thread and seat surfaces of crankshaft pulley bolt.
b. Tighten crankshaft pulley bolt.
c. Put a paint mark (B) on crankshaft pulley, mating with any one of six easy to recognize angle marks (A) on crankshaft bolt flange
(1).
d. Turn another 60 degrees clockwise (angle tightening). • Check the tightening angle with movement of one angle mark.
10. Check that crankshaft turns smoothly by rotating by hand clockwise using suitable tool.
11. Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
• Before starting engine, check oil/fluid levels, includi ng engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-11, "
Fluids and Lubricants".
• Use procedure below to check for fuel leaks.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leaks at connection points.
• Start engine. With engine speed increased, check again for fuel leaks at connection points.
• Run engine to check for unusual noise and vibration. NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there are no lea ks of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to spec- ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc.
Crankshaft pulley bolt : 35.0 N·m (3.6 kg-m, 26 ft-lb)
PBIC3726E
ItemBefore starting engine Engine runningAfter engine stopped
Engine coolant LevelLeaks Level
Engine oil LevelLeaks Level
Transmission/
transaxle fluid CVT Models
LeaksLevel/Leaks Leaks
M/T Models Level/Leaks LeaksLevel/Leaks
Other oils and fluids* LevelLeaks Level
Fuel LeaksLeaks Leaks
Exhaust gas —Leaks —
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-68
< REMOVAL AND INSTALLATION >[HR16DE]
CAMSHAFT
• Before starting engine, check oil/fluid levels, including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-11, "
Fluids and Lubricants".
• Use procedure below to check for fuel leaks.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leaks
at connection points.
• Start engine. With engine speed increased, che ck again for fuel leaks at connection points.
• Run engine to check for unusual noise and vibration. NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there is no leak s of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to spec- ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc.
InspectionINFOID:0000000012431722
INSPECTION AFTER REMOVAL
Oil Filter
• Check that there is no foreign material on the oil filter (1) and check it for clogging.
• Check the oil filter for damage.
• If there is some damage, replace the oil filter, the plug, and the washer as a set.
CAUTION:
Do not reuse the washer.
Camshaft Runout
1. Put V-block on a precise flat table, and support No. 2 and 5 jour- nals of camshaft.
CAUTION:
Do not support No. 1 journal (on the side of camshaft
sprocket) because it has a differe nt diameter from the other
four locations.
2. Set a suitable tool vertically to No. 3 journal.
3. Turn camshaft to one direction, and measure the camshaft runout using suitable tool. (Total indicator reading)
Item Before starting engine Engine runningAfter engine stopped
Engine coolant LevelLeaks Level
Engine oil LevelLeaks Level
Transmission/
transaxle fluid CVT Models
LeaksLevel/Leaks Leaks
M/T Models Level/Leaks LeaksLevel/Leaks
Other oils and fluids* LevelLeaks Level
Fuel LeaksLeaksLeaks
Exhaust gas —Leaks —
PBIC3693E
PBIC2499E
Revision: August 2015 2016 Versa Note

cardiagn.com

CYLINDER HEADEM-85
< REMOVAL AND INSTALLATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
*Power steering fluid, brake fluid, etc. Item
Before starting engine Engine runningAfter engine stopped
Engine coolant LevelLeaks Level
Engine oil LevelLeaks Level
Transmission/
transaxle fluid CVT Models
LeaksLevel/Leaks Leaks
M/T Models Level/Leaks LeaksLevel/Leaks
Other oils and fluids* LevelLeaks Level
Fuel LeaksLeaks Leaks
Exhaust gas —Leaks —
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-90
< UNIT REMOVAL AND INSTALLATION >[HR16DE]
ENGINE ASSEMBLY
• Before starting engine, check oil/fluid levels incl
uding engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-11, "
Fluids and Lubricants".
• Use procedure below to check for fuel leaks.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leaks
at connection points.
• Start engine. With engine speed increased, che ck again for fuel leaks at connection points.
• Run engine to check for unusual noise and vibration. NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there are no l eaks of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to spec- ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc. Item
Before starting engine Engine runningAfter engine stopped
Engine coolant LevelLeaks Level
Engine oil LevelLeaks Level
Transmission/
transaxle fluid CVT Models
LeaksLevel/Leaks Leaks
M/T Models Level/Leaks LeaksLevel/Leaks
Other oils and fluids* LevelLeaks Level
Fuel LeaksLeaksLeaks
Exhaust gas —Leaks —
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-1
ENGINE
C
DE
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
HR16DE
PRECAUTION ....... ........................................
8
PRECAUTIONS .............................................. .....8
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
8
On Board Diagnostic (OBD) System of Engine
and CVT ....................................................................
8
General Precautions .................................................9
PREPARATION ...........................................12
PREPARATION .............................................. ....12
Special Service Tools .......................................... ....12
Commercial Service Tools ......................................12
SYSTEM DESCRIPTION .............................14
COMPONENT PARTS ................................... ....14
ENGINE CONTROL SYSTEM ............................... ....14
ENGINE CONTROL SYSTEM :
Component Parts Location ....................................
14
ENGINE CONTROL SYSTEM : Component De-
scription ............................................................... ....
17
Accelerator Pedal Position Sensor ..........................18
Air Fuel Ratio Sensor 1 ...........................................19
Air Fuel Ratio Sensor 1 Heater ...............................19
Camshaft Position Sensor .......................................19
Clutch Pedal Position Switch ..................................20
Cooling Fan .............................................................20
Crankshaft Position Sensor .....................................20
ECM .................................................................... ....20
Electric Throttle Control Actuator ............................21
Engine Coolant Temperature Sensor ......................21
Engine Oil Pressure Sensor ....................................21
Engine Oil Temperature Sensor ..............................21
EVAP Canister Purge Volume Control Solenoid
Valve ................................................................... ....
22
EVAP Canister Vent Control Valve .........................22
EVAP Control System Pressure Sensor ..................22
Exhaust Valve Timing Cont rol Solenoid Valve ........23
Fuel Injector ......................................................... ....23
Fuel Pump ...............................................................23
Heated Oxygen Sensor 2 ........................................24
Heated Oxygen Sensor 2 Heater ............................24
Ignition Coil With Power Transistor .........................24
Intake Air Temperature Sensor ...............................24
Intake Valve Timing Control Solenoid Valve ...........25
Knock Sensor ...................................................... ....25
Battery Current Sensor (With Battery Tempera-
ture Sensor) .............................................................
25
Malfunction Indicator Lamp (MIL) ............................26
Mass Air Flow Sensor ..............................................26
Oil Pressure Warning Lamp ....................................26
Refrigerant Pressure Sensor ............................... ....27
Stop Lamp Switch & ASCD Brake Switch ...............27
Throttle Control Motor .......................................... ....27
Throttle Control Motor Relay ...................................27
Throttle Position Sensor ..........................................27
ASCD Steering Switch .............................................27
STRUCTURE AND OPERATION .....................28
Positive Crankcase Ventilation ................................28
On Board Refueling Vapor Recovery (ORVR) ........29
SYSTEM ............................................................30
ENGINE CONTROL SYSTEM ........................ ...........30
ENGINE CONTROL SYSTEM : System Diagram ....30
ENGINE CONTROL SYSTEM : System Descrip-
tion ...........................................................................
31
MULTIPORT FUEL INJECTION SYSTEM ................31
MULTIPORT FUEL INJECTION SYSTEM :
System Diagram ................................................. ....
32
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description ........................................................
32
ELECTRIC IGNITION SYSTEM .................................35
ELECTRIC IGNITION SYSTEM :
System Diagram ................................................. ....
35
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-6
Diagnosis Procedure .............................................356
P0850 PNP SWITCH .......................................358
Description ........................................................... ..358
DTC Logic ..............................................................358
Component Function Check ..................................359
Diagnosis Procedure .............................................359
P1078 EVT CONTROL POSITION SENSOR ..361
DTC Logic ............................................................ ..361
Diagnosis Procedure .............................................361
Component Inspection ...........................................363
P1148 CLOSED LOOP CONTROL .................364
DTC Logic ............................................................ ..364
Diagnosis Procedure .............................................364
P1212 TCS COMMUNICATION LINE .............365
Description ........................................................... ..365
DTC Logic ..............................................................365
Diagnosis Procedure .............................................365
P1217 ENGINE OVER TEMPERATURE .........366
DTC Logic ............................................................ ..366
Component Function Check ..................................366
Diagnosis Procedure .............................................367
P1225 TP SENSOR .........................................369
DTC Logic ............................................................ ..369
Diagnosis Procedure .............................................369
P1226 TP SENSOR .........................................370
DTC Logic ............................................................ ..370
Diagnosis Procedure .............................................370
P1550 BATTERY CURRENT SENSOR ..........371
DTC Logic ............................................................ ..371
Diagnosis Procedure .............................................371
Component Inspection ...........................................372
P1551, P1552 BATTERY CURRENT SEN-
SOR ..................................................................
373
DTC Logic ............................................................ ..373
Diagnosis Procedure .............................................373
Component Inspection ...........................................374
P1553 BATTERY CURRENT SENSOR ..........375
DTC Logic ............................................................ ..375
Diagnosis Procedure .............................................375
Component Inspection ...........................................376
P1554 BATTERY CURRENT SENSOR ..........377
DTC Logic ............................................................ ..377
Component Function Check ..................................377
Diagnosis Procedure .............................................378
Component Inspection ...........................................379
P1564 ASCD STEERING SWITCH .................380
DTC Logic ............................................................ ..380
Diagnosis Procedure .............................................380
Component Inspection ...........................................382
P1572 ASCD BRAKE SWITCH ........................383
DTC Logic ............................................................ .383
Diagnosis Procedure .............................................384
Component Inspection (ASCD Brake Switch) .......386
Component Inspection (Stop Lamp Switch) ..........386
P1574 ASCD VEHICLE SPEED SENSOR .......388
Description ........................................................... .388
DTC Logic .............................................................388
Diagnosis Procedure .............................................388
P159F ACTIVE GRILLE SHUTTER .................390
DTC Logic .............................................................390
Diagnosis Procedure .............................................391
P1715 INPUT SPEED SENSOR .......................392
Description ........................................................... .392
DTC Logic .............................................................392
Diagnosis Procedure .............................................392
P1720 VSS ........................................................394
Description ........................................................... .394
DTC Logic .............................................................394
Diagnosis Procedure .............................................394
P1805 BRAKE SWITCH ................................. ..396
DTC Logic ............................................................ .396
Diagnosis Procedure .............................................396
Component Inspection ..........................................397
P2096, P2097 A/F SENSOR 1 .........................398
DTC Logic ............................................................ .398
Diagnosis Procedure .............................................398
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY .....................................................
402
DTC Logic ............................................................ .402
Diagnosis Procedure .............................................402
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ........................................................
405
DTC Logic ............................................................ .405
Diagnosis Procedure .............................................405
Component Inspection ..........................................408
P2118 THROTTLE CONTROL MOTOR ..........409
DTC Logic ............................................................ .409
Diagnosis Procedure .............................................409
Component Inspection ..........................................410
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR ......................................................
411
DTC Logic ............................................................ .411
Diagnosis Procedure .............................................411
P2122, P2123 APP SENSOR ...........................413
DTC Logic ............................................................ .413
Diagnosis Procedure .............................................413
Component Inspection ..........................................414
P2127, P2128 APP SENSOR ...........................416
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-7
C
DE
F
G H
I
J
K L
M
EC A
N
O P
DTC Logic ...........................................................
..
416
Diagnosis Procedure .............................................416
Component Inspection ..........................................418
P2135 TP SENSOR ..........................................419
DTC Logic ........................................................... ..419
Diagnosis Procedure .............................................419
Component Inspection ..........................................420
P2138 APP SENSOR .......................................422
DTC Logic .............................................................422
Diagnosis Procedure .............................................422
Component Inspection ..........................................424
P219A AIR FUEL RATIO .................................426
DTC Logic ........................................................... ..426
Diagnosis Procedure .............................................427
P219C, P219D, P219E, P219F AIR FUEL RA-
TIO ....................................................................
431
DTC Logic ........................................................... ..431
Diagnosis Procedure .............................................433
ASCD BRAKE SWITCH ...................................437
Component Function Check ................................ ..437
Diagnosis Procedure .............................................437
Component Inspection (ASCD Brake Switch) .......438
CLUTCH PEDAL POSITION SWITCH .............439
Component Function Check ................................ ..439
Diagnosis Procedure .............................................439
Component Inspection (Clutch Pedal Position
Switch) ..................................................................
440
COOLING FAN .................................................441
Component Function Check ................................ ..441
Diagnosis Procedure .............................................441
Component Inspection (Cooling Fan Motor) .........443
Component Inspection (Cooling Fan Relay) .........443
ELECTRICAL LOAD SIGNAL .........................444
Description .......................................................... ..444
Component Function Check ..................................444
Diagnosis Procedure .............................................444
FUEL INJECTOR .............................................446
Component Function Check ................................ ..446
Diagnosis Procedure .............................................446
Component Inspection ..........................................447
FUEL PUMP .....................................................448
Component Function Check ................................ ..448
Diagnosis Procedure .............................................448
Component Inspection ..........................................450
IGNITION SIGNAL ...........................................451
Component Function Check ................................ ..451
Diagnosis Procedure .............................................451
Component Inspection (Ignition Coil with Power
Transistor) ........................................................... ..
454
Component Inspection (Condenser) ......................455
MALFUNCTION INDICATOR LAMP ..............456
Component Function Check ..................................456
Diagnosis Procedure .............................................456
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) ....................................................
457
Component Function Check ..................................457
Diagnosis Procedure .............................................457
Component Inspection (Refueling EVAP vapor cut
valve) ................................................................... ..
459
Component Inspection (Drain filter) .......................461
REFRIGERANT PRESSURE SENSOR ..........462
Component Function Check ..................................462
Diagnosis Procedure .............................................462
SYMPTOM DIAGNOSIS ............................464
ENGINE CONTROL SYSTEM SYMPTOMS ...464
Symptom Table ................................................... ..464
NORMAL OPERATING CONDITION .............470
Description .............................................................470
PERIODIC MAINTENANCE ......................471
IDLE SPEED .... ...............................................471
Inspection ............................................................ ..471
IGNITION TIMING ...........................................472
Inspection ..............................................................472
EVAPORATIVE EMISSION SYSTEM .............473
Inspection ..............................................................473
EVAP LEAK CHECK ......................................474
Inspection ..............................................................474
POSITIVE CRANKCASE VENTILATION .......476
Inspection ..............................................................476
REMOVAL AND INSTALLATION .............477
ECM .................................................................477
Exploded View ..................................................... ..477
Removal and Installation .......................................477
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... .......................................... .
478
SERVICE DATA AND SPECIFICATIONS
(SDS) ...............................................................
478
Idle Speed ........................................................... ..478
Ignition Timing .......................................................478
Calculated Load Value ..........................................478
Mass Air Flow Sensor ............................................478
Revision: August 2015 2016 Versa Note

cardiagn.com

COMPONENT PARTSEC-17
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ENGINE CONTROL SYSTEM : Component DescriptionINFOID:0000000012431270
1. ASCD steering switch
2. Active grille shutter3. Fuel level sensor unit and fuel pump
4. Fuel tank temperature sensor 5. EVAP control system pressure sen- sor6. EVAP canister
7. EVAP canister vent control valve 8. ASCD brake switch 9. Stop lamp switch
10. Clutch pedal position switch 11. Accelerator pedal position sensor
A. Fuel tank B. Rear under bodyC. Periphery of pedals
ALBIA1072ZZ
Component Reference
ECM EC-20, "
ECM"
A/F sensor 1EC-19, "Air Fuel Ratio Sensor 1"
A/F sensor 1 heaterEC-19, "Air Fuel Ratio Sensor 1 Heater"
Accelerator pedal position sensorEC-18, "Accelerator Pedal Position Sensor"
Cooling fan motor EC-20, "Cooling Fan"
Crankshaft position sensorEC-20, "Crankshaft Position Sensor"
Electric throttle control actuatorEC-21, "Electric Throttle Control Actuator"
Engine coolant temperature sensorEC-21, "Engine Coolant Temperature Sensor"
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-18
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
Accelerator Pedal Position Sensor
INFOID:0000000012431271
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometer which transform the accelerator pedal
position into output voltage, and emit the voltage signals to the ECM.
The ECM judges the current opening angle of the accelerator pedal
from these signals and controls the throttle control motor based on
these signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The
ECM uses this signal for the engine operation such as fuel cut.
Engine oil pressure sensor EC-21, "Engine Oil Pressure Sensor"
Engine oil temperature sensorEC-21, "Engine Oil Temperature Sensor"
EVAP canister purge volume control solenoid valveEC-22, "EVAP Canister Purge Volume Control Solenoid Valve"
EVAP canister vent control valveEC-22, "EVAP Canister Vent Control Valve"
EVAP control system pressure sensorEC-22, "EVAP Control System Pressure Sensor"
Exhaust valve timing control position sensor EC-19, "Camshaft Position Sensor"
Exhaust valve timing control solenoid valveEC-23, "Exhaust Valve Timing Control Solenoid Valve"
Fuel injectorEC-23, "Fuel Injector"
Fuel pumpEC-23, "Fuel Pump"
Heated oxygen sensor 2EC-24, "Heated Oxygen Sensor 2"
Heated oxygen sensor 2 heaterEC-24, "Heated Oxygen Sensor 2 Heater"
Ignition coil (with power transistor)EC-24, "Ignition Coil With Power Transistor"
Intake air temperature sensorEC-24, "Intake Air Temperature Sensor"
Camshaft position sensorEC-19, "Camshaft Position Sensor"
Intake valve timing control solenoid valveEC-25, "Intake Valve Timing Control Solenoid Valve"
Knock sensorEC-25, "Knock Sensor"
Mass air flow sensorEC-26, "Mass Air Flow Sensor"
PCV valveEC-28, "Positive Crankcase Ventilation"
Refrigerant pressure sensorEC-27, "Refrigerant Pressure Sensor"
Stop lamp switchEC-27, "Stop Lamp Switch & ASCD Brake Switch"
Throttle control motorEC-27, "Throttle Control Motor"
Throttle control motor relay EC-27, "Throttle Control Motor Relay"
Throttle position sensor EC-27, "Throttle Position Sensor"
ASCD steering switchEC-27, "ASCD Steering Switch"
ASCD brake switchEC-27, "Stop Lamp Switch & ASCD Brake Switch"
Clutch pedal position switchEC-20, "Clutch Pedal Position Switch"
Active grille shutterEXT-10, "ACTIVE GRILLE SHUTTER SYSTEM : Active grille shutter"
Component Reference
PBIB1741E
Revision: August 2015 2016 Versa Note

cardiagn.com

COMPONENT PARTSEC-27
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Refrigerant Pressure SensorINFOID:0000000012431299
The refrigerant pressure sensor is installed at the c
ondenser of the air conditioner system. The sensor uses an
electrostatic volume pressure transducer to convert refrigerant pressure to voltage. The voltage signal is sent
to ECM, and ECM controls cooling fan system.
Stop Lamp Switch & ASCD Brake SwitchINFOID:0000000012431300
Stop lamp switch and ASCD brake switch are installed to brake pedal bracket.
ECM detects the state of the brake pedal by those two types of input (ON/OFF signal).
Throttle Control MotorINFOID:0000000012431301
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feed-
back to the ECM to control the throttle valve in response to driving conditions via the throttle control motor.
Throttle Control Motor RelayINFOID:0000000012431302
Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle
control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends
an ON signal to throttle control motor relay and batte ry voltage is provided to the ECM. When the ignition
switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not
provided to the ECM.
Throttle Position SensorINFOID:0000000012431303
Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometer which transform the throttle valve position into
output voltage, and emit the voltage signals to the ECM. The ECM
judges the current opening angle of the throttle valve from these sig-
nals and controls the throttle valve in response to driving conditions
via the throttle control motor.
ASCD Steering SwitchINFOID:0000000012431304
ASCD steering switch has variant values of electrical resistance for each button. ECM reads voltage variation
of switch, and determines which button is operated.
PBIB2657E
Brake pedal ASCD brake switch Stop lamp switch
Released ONOFF
Depressed OFFON
PBIB0145E
Revision: August 2015 2016 Versa Note

cardiagn.com